CAME XVP S Configuration Manual
Hide thumbs
Also See for XVP S:
- Installation manual (8 pages) ,
- Installation and configuration manual (52 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CAME XVP S
Summary of Contents for CAME XVP S
- Page 1 FA01482-EN XVP F XVP S EN English CONFIGURATION MANUAL...
-
Page 2: Dismantling And Disposal
THE DATA AND INFORMATION IN THIS MANUAL MAY BE CHANGED AT ANY TIME AND WITHOUT NOTICE. THE MEASUREMENTS, UNLESS OTHERWISE STATED, ARE IN MILLIMETRES. DESCRIPTION XVP S: Wall-mounted video-entry panel with touch screen for IP360 system. XVP F: Recessed video-entry panel with touch screen for IP360 system. Function of terminals ❶ Local power supply input 12-24 V DC... -
Page 3: Error Alerts
Error alerts When shown on the display, this indicates that there is a programming error. The possible causes are listed below: High temperature Non-compliant installation; Heat sources near the device; Direct sunlight; Hardware failure Ethernet connection Defective or incorrectly connected CAT5 cable; Incorrect DATA connection;... - Page 4 A page with some system information is displayed. ❶ Device model. ❷ This is the unique device ID. Use for PCS/XIP tool programming. ❶ Model: XVP ❸ Device hardware version. ❷ Serial number: 0097c002 ❹ Software installed on the device. ❸ HW version: 1.0 ❺...
- Page 5 For this reason, some parameters can only be modified from the installer profile. Settings Language Date/Time Screen Tones LEDs and sensors Network SIP settings CAME Connect Multimedia Access Control User-Interface Configuration Maintenance Choosing the interface language ❶ Choose the interface language. ❷ Save the configuration. ❸...
-
Page 6: Setting The Screen Brightness
Date and time setting ❶ Choose between manual and auto mode. ❷ In automatic mode, choose whether to synchronise DATE/TIME DATE/TIME to your XIP system master or an external service (NTP). If you select NTP, the network that the device ❶... - Page 7 LED and sensor enabling ❶ Enable the screen activation in proximity to the device. ❻ LEDS AND SENSORS If the function is not enabled, the screen can only be activated by touch. ❷ Set the sensitivity of the proximity sensor: low (short distances), medium or high (maximum distance). The proximity sensor distances may vary slightly depending on the person and the direct lighting conditions PROXIMITY of the device.
- Page 8 ❷ Enable video-entry call VoIP remote control. ❶ Keycode Connection to CAME Connect is disabled by default. The CAME Connect connection must be active to receive calls over the app. ❷ ❸ URL for the remote calling service (default: xip01.cameconnect.net) Enable connection ❹...
-
Page 9: Sip Settings
This screen explains how to check the network connection. Checking the connection status... CAME CONNECT Checking the LAN interface configuration... Checking if the default GW is reachable... Checking if the DNS is reachable... CHECK YOUR CONNECTION Checking if the provider is reachable... -
Page 10: Access Control
Access control Access Control PIN scramble keyboard: if enabled, every time the numerical keypad is called up for access control, the keys appear in a random order. Save: Save the configuration. PIN scramble keyboard Save User interface configuration User Interface Configuration Call page style: select the style of the call page. - Page 11 Device maintenance ❶ Tap to restart the device. MAINTENANCE ❷ Tap to restart the graphic user interface and the video-entry call functions. ❸ Tap to restore all local settings to the default factory settings. ❶ Reboot device ❷ Restart application ❸...
-
Page 12: System Settings
Entering programming mode Some of these sections require specific knowledge of how to operate the video-entry system. Incorrect configuration may cause full or partial malfunctions. For this reason, some parameters can only be modified from the installer profile (default password 112233). To access the configuration web page, type the address of the device to be configured into the browser address bar (Chrome, Firefox, Safari). - Page 13 ❶ Choose between manual and auto mode. Date and Time Help Exit In automatic mode, it allows to choose to synchronise to the XIP system master or to an external service (NTP). System By selecting NTP, the network to which the device is connected must be able TIME SETTINGS Date and Time Date and Time...
-
Page 14: Network Settings
Network settings CONNECTIONS Network Help Exit ❶ Device MAC ADDRESS, cannot be edited. System CAMECONNECT CONNECTIONS ❷ Choose the type of addressing. DHCP MAC ADDRESS Date and Time ❶ The device’s IP address is assigned by the DHCP server. Network Network If the device is configured as the master (serverless system), make sure that the DHCP server always assigns the same IP address to the device. - Page 15 SIP settings ACCOUNT c83f78d1-8376-42b9-8273-bf7ea448d408 9b424af7-e528-4dbf-8968-113493daa Exit Help ❶ SIP username assigned to device by PCS/XIP. ACCOUNT TRUNKS FEATURES NODES STATUS FEATURES ❷ Name assigned to the device by PCS/XIP. System ❸ Server IP address assigned to the device by PCS/XIP. Date and Time Once configuration is complete, the ACCOUNT STATUS on the SYSTEM page will USERNAME...
- Page 16 NODE STATUS (MASTER device only) 43dbcc62-5c2d-4ddb-a618-3af299839189 9b424af7-e528-4dbf-8968-113493daa2e9 List of SIP VoIP devices in the system and their registration status at the MASTER XVP entry Exit Help panel. Green icon The device is registered correctly. ACCOUNT TRUNKS FEATURES NODES STATUS System d09e0537-3e7f-4277-a94c-b6775f081e0e 821025f4-e9da-4c8a-8fcd-827e86a06868 Red icon...
-
Page 17: Mobile App
M OBILE APP (MASTER device only) e8941d2a-5550-4801-9ef5-3cadb21a174f 9b424af7-e528-4dbf-8968-113493daa2e9 List of Mobile APP devices, which require a licence and use the MASTER XVP entry panel CREDENTIALS Exit Help as the MASTER IP server as the registration server. LICENCES XIP RECEIVERS MOBILE APP GENERIC SIP ❼... -
Page 18: Device Settings
❹ SURNAME Authorisations for pathways and access points are defined by PCS/XIP. BADGE CODE ❺ Credentials Access control Access control SURNAME NAME CAME Device ❼ User 1 IP unit Images and logos Maintenance User 2 IP2 unit ❻ Diagnostics... - Page 19 SCREEN ❶ Adjust the screen brightness according to the lighting conditions. Device Help Exit ❷ Adjust the screen brightness during use, if automatic brightness is not AUDIO SCREEN SENSORS MULTIMEDIA RTSP System activated. ❸ Adjust the screensaver brightness when the screen is in standby mode. Date and Time Network ❶...
- Page 20 LOGO GALLERY section Help Exit Images and logos The gallery of logos stored on the device is shown. Click on the (+) to LOGO GALLERY IMAGES GALLERY MAP GALLERY ASSIGNING IMAGES System add a new image to the gallery. Click on one or more images to select Date and Time them.
-
Page 21: Device Maintenance
ASSIGNING IMAGES Immagini e Loghi Aiuto Esci You can select the TYPE of images to be assigned from APPEARANCE, GROUPS LOGO GALLERY IMAGES GALLERY MAP GALLERY ASSIGNING IMAGES System or USERS. If APPEARANCE is selected, you can choose the image you want to use as the Date and Time NODE TYPE logo and screensaver from those available in the logo gallery. -
Page 22: System Configuration
SYSTEM CONFIGURATION ❸ Restore factory settings on the main module and connected accessories. Maintenance Help Exit System INFO UPDATES SYSTEM CONFIGURATION Date and Time Network FACTORY RESET Credentials ❸ Global Access control Device Images and logos Maintenance Maintenance Diagnostics Device diagnostics STATISTICS Help Diagnostics... - Page 23 CONFIGURATION AND COMMISSIONING VIA PCS/XIP The device is part of a set-up based on an Xip system. The system structure must be built using PCS/XIP software. Create the system structure according to need. XVP properties First name Address Addressing mode IP address Conversation time (s) The “Ring time”...
- Page 24 CAME S.p.A. Via Martiri Della Libertà, 15 31030 Dosson di Casier - Treviso - Italy tel. (+39) 0422 4940 - fax. (+39) 0422 4941...