OREC RABBIT RM60W Instruction Manual
  1. Manuals
  2. Brands
  3. OREC Manuals
  4. Farm Equipment
  5. RABBIT RM60W
  6. Instruction manual

OREC RABBIT RM60W Instruction Manual

Grassland mower
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
GRASSLAND MOWER RABBIT RM60W
Read this instruction manual carefully before any use of the machine, keep it as a reference. For any question
about this manual, please report to your OREC dealer or to the distributor of your country.
OREC CO LTD
548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN JAPON
http://www.orec-jp.com
Updated : June 2021

Advertisement

Table of Contents
loading

Related Manuals for OREC RABBIT RM60W

Summary of Contents for OREC RABBIT RM60W

  • Page 1 GRASSLAND MOWER RABBIT RM60W Read this instruction manual carefully before any use of the machine, keep it as a reference. For any question about this manual, please report to your OREC dealer or to the distributor of your country. OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN JAPON http://www.orec-jp.com...

  • Page 2: Introduction

    Use only the OREC original parts : “ non genuine ” parts will not assure you of a correct and safe working and are likely to make the guarantee null and void. Write the name and the serial number of your machine hereunder : OREC CO.,LTD MADE IN JAPAN...

  • Page 3: Table Of Contents

    CHECK LIST INSTRUCTIONS TO THE DEALER The assembly, the installation and the first application of the machine is under the OREC dealer’s responsability. Read the instruction manual as well as the safety measures. Check that all the before delivery and at delivery check points specified in the following lists have been verified and possibly modified before delivering the machine to its owner.

  • Page 4: Safety Rules

    Be careful when working on slopes.  Keep away from high-tension lines and obstacles. A contact with a high-tension line cause electrocution and  death. Stop the machine progressively when travelling up and down slopes.  OREC RM60W...
  • Page 5 Always use a chuck and bronze hammer when replacing or intervening on the pins  and bolts at the end of rams, rod … etc in order to avoid the projection of metal fragments OREC RM60W...

  • Page 6: Safety Instruction Stickers

    Beware of rotating parts under Keep hands and feet away from Beware of thrown objects Stay away from the machine the shields rotating blades Keep hands and feet away from rotating blades Beware of rotating parts under the shields OREC RM60W...

  • Page 7: Machine Description

    Parking brake light Pilot lamp (GREEN) Auto cruise lever Brake locking lever Throttle Choke lever Offset open/close lever Hour meter Engine Switch Blade Clutch Lever Fuse BOX Offset left Height of Cut lever Driving clutch lever Buttery BOX OREC RM60W...

  • Page 8: Controls

    ” position, speed control lever does not return to neutral position(except reverse speed). Remember to activate the auto cruise only when machine is stopped. Auto cruise is cancelled when brake pedal is pressed, then speed control lever returns to neutral position. OREC RM60W...
  • Page 9 It is possible to move the offset angle in 3 positions. When the lever is in MAX position, offset is fully open. When the lever is in MINI position, offset is fully closed. Offset lever is located in both right and left. Right lever operates offset R, and left lever operates offset L. OREC RM60W...

  • Page 10: Inspection Before Use

    FUEL INSPECTION AND REFUELLING Place the machine on flat surface and remove fuel cap. Check Fuel cap the level of fuel through fuel mouth. In case fuel gauge is close to “E”, it is necessary to refuel. Fuel gauge OREC RM60W...
  • Page 11 2) Use only lead-free regular gasoline. Otherwise, engine might be damaged. 3) Gasoline degrades by time. In case of non-use for more than 1 month, replace gasoline to new one. Also, do not use gasoline stored in polyethylene tank. OREC RM60W...

  • Page 12: Operation

    Make sure that speed lever is in N position, then pull the choke lever(pull to close, push to open) if engine is not warm enough. Move the throttle lever to intermediate position between MAX and MINI(upper position is MAX and lower position is MINI). Choke OREC RM60W...
  • Page 13 Slowly shift the speed control lever forward and start drving. TIP : Brake stopper Driving speed is adjusted following the tilt angle of speed control lever. For your safety, start driving in low speed. Unlock Parking brake pedal OREC RM60W...
  • Page 14 Except the use in PUSH MODE, alwayd place the driving clutch lever in ON position. For safety, PUSH MODE is recommened for two person or more. On the slope, do not place the driving clutch lever to OFF, because it may cause slipping accident. OREC RM60W...
  • Page 15 OWING Start the engine. Move the throttle lever to MAX and increase engine rpm. Place height of cut lever at 100mm. Push down the blade clutch lever forward. OREC RM60W...
  • Page 16 5) Basically use speed lever to stop the machine. In case of emergency situation, machine stops when parking brake pedal is pressed. At same time, speed lever goes back to N position. 6) Remember to remove key and keep it when operator leave the machine. OREC RM60W...
  • Page 17 Offset wing can mow up to 10 degee from main cutting deck. It is conveninet for mowing around the tree, which is slightly hilly. Pay special attention for risk of thrown ojbect while offset wing is lifted up. OREC RM60W...

  • Page 18: Maintenance Operations To Be Carried Out By The User

    When the gasket(O ring) contact the position, turn the plug in 3/4 rotation to fix it. NGINE OIL CAUTION Excess or deficiency of engine oil will cause engine trouble. Add engine oil in case of deficiency and reduce it in case of excess to maintain proper volume. Inpsection and filling up OREC RM60W...
  • Page 19 Check the oil volume by level gauge, and securely tighten the oil cap. Run the engine for 2 minutes in low rpm, to check the leaking of oil around the filter. Stop the engine and check the oil volume again. Add oil in case of deficiency. OREC RM60W...
  • Page 20 Then remove the HST oil tank cap. Put 500ml of HST oil and also relace the moisture adsorption sheet at same time. After the HST oil is filled, make sure that HT oil tank cap is securely fixed. HST tank cap Moisture Adsorption sheet OREC RM60W...
  • Page 21 If grease is not properly lubricated, it leads to poor movement of machine and cause damages. Grease nipple is located in each axle part. Use grease gun to lubricate. ⑦ ⑧ ⑨ ⑤ ⑥ ④ ⑩ ⑪ ⑬ ⑫ OREC RM60W...
  • Page 22 Fuel hose and rubber items degrade even if machine is not used. Remember to replace them together with clips every 3 year of when they are damaged. Pay attention not to let dust to go into the hose. Before evey use, check if fuel hose or fixing band are damaged or loosened. OREC RM60W...
  • Page 23 Using the machine with engine exhaust system covered by grass leads to cause of overheat. Engine temperature may rise up and cause fire accident. Remove the mad and grass from exhaust pipe and muffler cover before every use. Exhaust pipe Remove dust and grass around engine exhaust pipe by air blow. OREC RM60W...
  • Page 24 Seat re- main fixed when seat bracket is maximum opened. Remove the side covers to adjust wire and rod. Contact your nearest dealer to replace driving belt and blade belt. Seat bracket OREC RM60W...
  • Page 25 Blade pulley Place the blade clutch lever to ON( ). Belt holder(pic.2) Engine pulley Belt holder(pic.1) As shown in figure(left), adjust the gap between belt holder of blade pulley and back of belt to be 2-3mm. Belt holder(pic.1) OREC RM60W...
  • Page 26 After the adjustment, securely tighten the lock nut. If it is not possible to make adjustment, brake shoe may be worn out. Contact your nearest dealer for inspection and replacement. Lock nut Adjust nut OREC RM60W...
  • Page 27 Loosen the lock nut on turn buckle linked with speed lever, then turn it to adjust. If machine slightly moves forward, -Move the turn buckle toward A. If machine slightly moves backward, -Move the turn buckle toward B. Turn buckle After this adjustment, securely tighten the lock nut. OREC RM60W...
  • Page 28 If differential lock is not activated, -Move the adjust nut toward A. If differential lock is not cancelled, -Move the adjust nut toward B. Lock nut After this adjustment, securely tighten the lock nut. OREC RM60W...
  • Page 29 Do not forget to remove the soil or grass which comes into tires. If they remain around the tire for a long time, tire wheel, oil seal or bearing on the front wheel may be damaged. Remove the mud and grass inside the tire wheel. OREC RM60W...
  • Page 30 Blade rotates left on cutter unit(L) and rotates right in cutter unit(R). Therefore, on M12 bag nut on cutter unit(R), left-hand screw is used to avoid loosening. And on M12 bag nut on cutter unit(L), right-hand screw is used in same reason. Pay special attention on desorption or replacement of knife neck guard. OREC RM60W...
  • Page 31 Set the offset blade on blade holder and fix them by ro- Cutter unit(L) Cutter unit(R) tary protector. Place the removed nut in original position and securely fix it. Pay attention to right-hand screw and left-hand screw. Offset blade Blade holder Rotary protector bag nut OREC RM60W...
  • Page 32 OTICE FOR NEXT USE CAUTION Use fresh fuel. Execute pre-use inspection. Make sure if each control levers work properly(before every use). Make sure if all bolts and nuts are not loose and in place. OREC RM60W...
  • Page 33 Operate the machine for short time, and check if abnormal sound and abnormal temperature are found or not. For warming up each part of machine, operate the machine lightly for first 2-3 hours. OREC RM60W...
  • Page 34 Looseness, wear, and loss of bolt Setting and nut Handle Setting Looseness, wear, and loss of bolt Handle and nut Meter Hour meter Indication of correct hour, proper Hour meter displaying Label Warning label/plate Attachment of label, damage or dirt Label OREC RM60W...
  • Page 35 Replace to good quality fuel. Engine stops Ignition coil is not good. Replace the ignition coil. later Fuel filter is clogged. Replace the fuel filter. Exhast gas Fuel quality is bad. Replace to good quality fuel. badly smells OREC RM60W...

  • Page 36: Breakdowns And Solutions

    Water is coming into brake drum. Press and release the brake and dry inside. Tire is worn. Replace the tire. * If you have any questions or do not understand any points, please contact your dealer. OREC RM60W...

  • Page 37: Tightening Torques (Nm)

    313,8 to 353 441,3 to 480,5 617,8 to 657,1 176,5 to 205,9 421,7 to 451,1 539,4 to 578,6 608 to 647,2 843,4 to 882,6 235,4 to 264,8 539,4 to 568,8 706,1 to 745,3 784,5 to 823,8 1098,4 to 1137,6 OREC RM60W...

  • Page 38: Ec Conformity Declaration

    EC CONFORMITY DECLARATION Business name and full address of the manufacturer: OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN FUKUOKA JAPAN S.A.T. sarl - Force 7 – ZA – 38110 ROCHETOIRIN France owner of the technical documents Designation : Ride-on brush cutter...

  • Page 39: Limited Warranty

    OREC. 2° Each part concerned by a guarantee claim must be returned to OREC’s in order to be inspected, repaired or replaced. The part(s) must be returned with freight prepaid and must be accompanied with a proof of the purchase.

This manual is also suitable for:

Rmk60w

Table of Contents