Table of Contents
Advertisement
Quick Links
OWNER'S MANUAL
Transporter LS 280 / LS360 / LS461
Compact Transporter
Read this instuction manual carefully before any use of the machine, keep it as a reference. For
any question about this manual, please report to your OREC dealer or to the distributor of your
country or to : http://www.orec-jp.com.
Update : September 2016
Advertisement
Table of Contents
Related Manuals for OREC LS 280
Summary of Contents for OREC LS 280
- Page 1 Compact Transporter Read this instuction manual carefully before any use of the machine, keep it as a reference. For any question about this manual, please report to your OREC dealer or to the distributor of your country or to : http://www.orec-jp.com.
-
Page 2: Introduction
Use only the OREC original parts : “ non genuine ” parts will not assure you of a correct and safe working and are likely to make the guarantee null and void. Write the name and the serial number of your machine hereunder : MODEL :.................. -
Page 3: Table Of Contents
CONTENTS INTRODUCTION ............................... 2 CONTENTS ..............................3 SPECIFICATIONS ............................3 LOADING CAPACITY ............................3 CHECK LIST ..............................4 SAFETY RULES ............................... 4 DIFFERENT PARTS OF TRANSPORTER (LS280) ..................6 DIFFERENT PARTS OF TRANSPORTER (LS360) ..................7 DIFFERENT PARTS OF TRANSPORTER (LS461) ..................8 SAFETY INSTRUCTION STICKERS ........................ -
Page 4: Check List
CHECK LIST INSTRUCTIONS TO THE DEALER • The assembling, the installation and the first application of the machine is under the OREC dealer’s responsability. • Read the instruction manual as well as the safety measures. Check that all the before delivery and at delivery check points specified in the following lists have been verified and possibly modified before delivering the machine to its owner. - Page 5 Never stop or start roughly when working on a slope. Never use the machine to work on a stepping • terrain. Reduce the ground speed when driving on a slope and when turning straight • in order to prevent from any risk of losing control. Be very careful when bordering ditches.
-
Page 6: Different Parts Of Transporter (Ls280)
DIFFERENT PARTS OF TRANSPORTER (LS280) Travel Lever Front Right Side Clutch Lever Driving Sprocket Speed change Lever Recoil Starter Foot Rest (LS280) Turning Wheel Idle Wheel left rear On/off engine switch Dumping lever Exhaust silencer Throttle lever Fuel tank Stand ©... -
Page 7: Different Parts Of Transporter (Ls360)
DIFFERENT PARTS OF TRANSPORTER (LS360) Travel Lever Front Right Side Clutch Levers Driving Sprocket Speed change Lever Recoil Starter Turning Wheel left Idle Wheel rear Throttle lever On/off engine switch Dumping lever Fuel tank Stand Air filter © SAT – 09/2006... -
Page 8: Different Parts Of Transporter (Ls461)
DIFFERENT PARTS OF TRANSPORTER (LS461) Right Travel Lever Front Throttle lever Idle Wheel Fuel tank Turning Wheel Driving Sprocket Dumping Recoil Starter On/off engine lever switch Air filter muffler rear left Side Clutch Levers Speed change Lever © SAT – 09/2006... -
Page 9: Safety Instruction Stickers
SAFETY INSTRUCTION STICKERS Note their location and replace them immediately in case of damage or when missing Before doing maintenance Stand clear of the machine remove the spark plug Beware of hot surfaces exhaust gases and burnt read owner’s manual read owner’s manual Beware of the rotating parts under the shield. -
Page 10: Controls
CONTROLS Travel lever(A, figure1) This lever transmits the power from the engine to the transmission. Grip the lever with the handlebar and it will be in "driving" position. Release the handlebar and it will be in "stop" position. The driving clutch lever is connected with the brake. - Page 11 Foot rest pedal(only LS280) (figure 4) Push the pedal and the handlebar to low down the foot rest. Push the pedal and pull the handlebar to raise the foot rest. Check that the foot rest is fully locked when raised Figure 4 ©...
-
Page 12: Operation
OPERATION DANGER It is prohibited to overload ! CAUTION Check the tightening of bolts, referring to the tightening torque chart The safety was one of our main worry when designing and manufacturing this machine. Therefore, negligence in the use of the machine should reduce our efforts to nothing. The prevention strictly depends on the care and on the skill of the user when applying and maintening the machine.The best safety method remains a careful and skilled user ;... - Page 13 Make the machine moving - Select the speed (gear ratio) in accordance with the work to do.(Figure 8) - Turn the throttle to increase engine speed -Press slowly the travel lever (Figure 9 A) Figure 9 Figure 8 Raising the Loading Box 1.
- Page 14 WARNING If the loading box is unlocked on the slope or when the load is clustered on the front side the loading box may suddenly start dumping. How to stop the machine Release the travel clutch lever. (Figure 10) • Pull back the throttle lever to idle position.
-
Page 15: Maintenance Operations To Be Carried Out By The User
MAINTENANCE OPERATIONS TO BE CARRIED OUT BY THE USER CAUTION Although oil is filled when the machine is shipped, check if designated amount of oil is filled in designated places before using the machine. Exchange oil regularly to keep the machine in good condition. When inspecting, exchanging, or refuelling oil, put the machine on the large flat ground. - Page 16 CAUTION Do not use inflammable oil such as gasoline and thinner. Other Inspection 1. Check if each handling lever works properly. (Each time before starting the engine.) 2. Stretch the V belt after a few driving hours, as it tends to be loose at first. (Refer to "Driving Clutch Wire".) 3.
- Page 17 Air Filter (Figure 18) CAUTION If the air cleaner is choked, it may cause the shortage of output and the waste of fuel as well as fire. Make sure to clean it regularly. If you drive the machine without the air cleaner, the machine will absorb dust and damage the engine 1.
- Page 18 Fulcrum of travel Tension Arm (figure 20, see A) Fulcrum of Dump (figure 21, see A) Fulcrum of Change Lever (figure 22, see A) Figure 19 Figure 20 Figure 22 Figure 21 © SAT – 09/2006...
- Page 19 Driving Clutch Wire (A, figure 23) 1. Release the driving clutch lever to "stop” the machine. Let the running clutch lever free. 2. Loosen the lock nut on the running clutch wire. 3. Turn the adjusting nut and adjust the tension of the running clutch wire. If the V belt slips with the load even if you shift the driving clutch lever to "on"...
- Page 20 Adjusting Belt Holder Tips; The ill-adjusted belt holder as well as wire may hinder the function of the running clutch. After removing the belt holder to exchange the V belt, adjust the belt holder as follows. 1. Let the platform dump. 2.
- Page 21 If freezing dirt at the machine hinders smooth operation, do not try to drive by force. Pour hot water on that part or wait till it melts. (OREC is not responsible for the damage caused by forced driving.) Detailed Statement of Bag for Tools...
-
Page 22: List For Regular Self-Inspection
LIST FOR REGULAR SELF-INSPECTION Negligence of inspection and service may cause an accident. To use the machine efficiently and safely, inspect the machine according to the following list. Do the yearly-check (Y) once a year, monthly-check (M) once a month and daily-check (D) each time you use the machine. - Page 23 Turning 1. Function of Side Clutch Is normal. Device Body Platform 1. Up- and Underside of Platform, Is normal. & & Function of Door Door Door 2. Crack, Deformation and Corrosion of Is not recognized. Each Part 3. Slack or Drop of Bolts or Nuts Is not recognized.
- Page 24 Causes of Trouble and Measures If the following phenomena occur, deal with them correctly according to the Phenomenon Cause Measure Machine does not Running clutch wire is not adjusted. Adjust running clutch wire. start. (Running clutch V belt is worn out or damaged. Exchange belt.
- Page 25 Bad Condition of Engine and How to Deal with It When the engine is in bad condition, deal with it properly according to the following list. Phenomenon Cause Measure Machine does not start Throttle lever is not in “start" position. Change throttle lever to "start".
-
Page 26: How To Assemble : Dealer Instructions
HOW TO ASSEMBLE : DEALER INSTRUCTIONS Assemble the machine on the flat place. Check if there are the bags of tools in the carton of machine. Check if the quantity of oil is enough before using machine although the machine is oiled. (Quantity of oil: refer to page 15 of the instruction manual) ASSEMBLE OF LS280 1. - Page 27 ASSEMBLE OF LS360 1. Put the handle into the bracket and tightens the bolt with the cap nut. Fix the both sides of the clutch levers with the R pin. 2.Tie the handle of right side, side clutch wire and throttle wire ,switch harness with wire belt. Then, tie the handle of left side, side clutch wire, running clutch wire, brake wire, with the wire belt.
-
Page 28: Ec Conformity Declaration
EC CONFORMITY DECLARATION Business name and full address of the manufacturer : OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN FUKUOKA JAPAN Designation : walk behind crawler dumper Mark : OREC Type : LS280 Serial Identification : Engine : - Manufacturer :... -
Page 29: Ec Conformity Declaration
EC CONFORMITY DECLARATION Business name and full address of the manufacturer : OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN FUKUOKA JAPAN Designation : walk behind crawler dumper Mark : OREC Type : LS360 Serial Identification : Engine : - Manufacturer :... -
Page 30: Ec Conformity Declaration
EC CONFORMITY DECLARATION Business name and full address of the manufacturer : OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN FUKUOKA JAPAN Designation : walk behind crawler dumper Mark : OREC Type : LS360 Serial Identification : Engine : - Manufacturer :... -
Page 31: Ec Conformity Declaration
EC CONFORMITY DECLARATION Business name and full address of the manufacturer : OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN FUKUOKA JAPAN Designation : walk behind crawler dumper Mark : OREC Type : LS461 Serial Identification : Engine : - Manufacturer :... -
Page 32: Tightening Torque (Danm)
The machine must not have been damaged in a road accident, roughly handled or unproperly used. This guarantee does not compell OREC or its dealer to reimburse the labour costs or the carriage costs to the repairer. NO OTHER GUARANTEE SHALL BE APPLIED TO THIS MACHINE EXCEPT THE LEGAL GUARANTEE. -
Page 33: Notes
NOTES ................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................©...