Table of Contents
Advertisement
Note
f The AC voltage monitor function, the network function, the <SERIAL OUT> terminal, and part of the RS-232C command cannot be used
during the standby when set to [ECO].
When an error or warning occurs on the projector, the self-diagnosis display appears on the control panel regardless of the [STANDBY
MODE] settings. (x page 235)
f When [ECO] is set, it may take approximately 10 seconds longer before the projector starts projecting after the power is turned on,
compared with when [NORMAL] is set.
f When [NORMAL] is set, the network function and the <SERIAL OUT> terminal can be used during standby.
f When [NORMAL] is set, power can be supplied by using the <DC OUT 1> terminal or the <DC OUT 2> terminal even while the projector is
in standby mode. If [ECO] is set, power cannot be supplied in standby mode.
f The [STANDBY MODE] setting does not return to factory default setting even if the [PROJECTOR SETUP] menu → [INITIALIZE] → [ALL
USER DATA] is executed.
[NO SIGNAL SHUT-OFF]
A function that automatically switches the power source of the projector to standby if there is no input signal for a
certain period of time. The time before switching to standby can be set.
1)
Press as to select [NO SIGNAL SHUT-OFF].
2)
Press qw to switch the item.
f The items will switch each time you press the button.
[DISABLE]
[10MIN.] - [90MIN.]
[NO SIGNAL LIGHTS-OUT]
This is a function to automatically turn off the light source of the projector when there is no input signal for specific
period. The time until the light source is turned off can be set.
1)
Press as to select [NO SIGNAL LIGHTS-OUT].
2)
Press qw to switch the item.
f The items will switch each time you press the button.
[DISABLE]
[10SEC.] - [5MIN.]
Note
f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the no signal lights-out function is operating and the light source
is turned off.
f When [NO SIGNAL LIGHTS-OUT] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on
again from the condition that the light source has turned off by this function.
g When the signal is input
g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
g When the power on <b> button is pressed
g When the operation to disable the shutter function (shutter: open) is performed, such as pressing the <SHUTTER> button
g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up
f The no signal lights-out function is disabled in following cases.
g When the [DISPLAY OPTION] menu → [BACK COLOR] is set to [DEFAULT LOGO] or [USER LOGO], and the Panasonic logo or the
image registered by the user is displayed on the projected image
g When the [SECURITY] menu → [DISPLAY SETTING] is set to [TEXT] or [USER LOGO], and the security message (text or image)
registered by the user is displayed on the projected image
[INITIAL STARTUP]
Set the startup method when the <MAIN POWER> switch is set to <ON>.
1)
Press as to select [INITIAL STARTUP].
2)
Press qw to switch the item.
f The items will switch each time you press the button.
[LAST MEMORY]
[STANDBY]
[ON]
Chapter 4 Settings — [PROJECTOR SETUP] menu
Disables the No signal shut-off function.
Sets the time in increments of 10 minutes.
Disables the no signal lights-out function.
Turns off the light source when there is no input signal for the preset period.
Select [10SEC.], [20SEC.], [30SEC.], [1MIN.], [2MIN.], [3MIN.], or [5MIN.].
Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.
Starts up the projector in standby.
Starts projecting immediately.
ENGLISH - 177
Advertisement
Table of Contents
