Table of Contents
Advertisement
r 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G)
This board supports the SD-SDI signal, HD-SDI signal, and 3G-SDI signal.
1
<3G-SDI 2 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 4 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 2 IN> terminal/<3G-SDI 4 IN> terminal of this
board.
2
<3G-SDI 2 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 4 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input SDI signal.
Note
f This projector does not support audio output because it is not equipped with audio function. However, when SDI signal with audio is input to
the <3G-SDI 1 IN>/<3G-SDI 2 IN>/<3G-SDI 3 IN>/<3G-SDI 4 IN> terminal, a signal with audio is output from the <3G-SDI 1 OUT>/<3G-SDI
2 OUT>/<3G-SDI 3 OUT>/<3G-SDI 4 OUT> terminal.
f To use the 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G), it is necessary for the firmware version of the 3G-SDI Terminal
Board with Audio to be 2.00 or later. Confirm the firmware version of the 3G-SDI Terminal Board with Audio when it does not operate after
installing to the projector.
Consult your dealer regarding the version update to the latest firmware if the version is earlier than 2.00.
For details on how to confirm the firmware version, refer to "How to confirm the firmware version of the Interface Board (optional)"
(x page 36).
r Interface Board for 12G-SDI (Model No.: ET-MDN12G10)
This board supports the SD-SDI signal, HD-SDI signal, 3G-SDI signal, 6G-SDI signal, and 12G-SDI signal.
1
<SDI 1 IN> terminal
This is a terminal to input SDI signal (SD-SDI/
HD-SDI/3G-SDI/6G-SDI/12G-SDI).
2
<SDI 2 IN/1 OUT> terminal
This is a terminal to input SDI signal (SD-SDI/HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(SD-SDI/HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 1
IN> terminal of this board.
Note
f The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal.
f To use the <SDI 2 IN/1 OUT> terminal or the <SDI 4 IN/3 OUT> terminal as an output terminal, set the [DISPLAY OPTION] menu → [SLOT
IN] → [SDI MODE] to [OUTPUT].
f When the projector is in standby mode, a signal is not output from the <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal.
f Install this board in either <SLOT 1> or <SLOT 2>. When these boards are installed in both <SLOT 1> and <SLOT 2>, only the board
installed in <SLOT 1> can be used.
Chapter 1 Preparation — About your projector
1
2
5
1
2
3
4
5
3
<3G-SDI 1 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 3 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 1 IN> terminal/<3G-SDI 3 IN> terminal of this
board.
4
<3G-SDI 1 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 3 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input SDI signal.
5
Handle
3
4
5
3
<SDI 3 IN> terminal
This is a terminal to input SDI signal (SD-SDI/
HD-SDI/3G-SDI/6G-SDI/12G-SDI).
4
<SDI 4 IN/3 OUT> terminal
This is a terminal to input SDI signal (SD-SDI/HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(SD-SDI/HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 3
IN> terminal of this board.
5
Handle
ENGLISH - 35
Advertisement
Table of Contents
