Table of Contents
Advertisement
[SERIAL NUMBER]
[PROJECTOR RUNTIME]
[LIGHT RUNTIME]
[CONTINUOUS LIGHTING
TIME]
[MAIN/SUB VERSION]
[INTAKE AIR TEMP.]
[OPTICS MODULE TEMP.]
[EXHAUST AIR TEMP.]
[LIGHT1 TEMP.]
*1
[LIGHT2 TEMP.]
*1
[SELF TEST]
[INPUT]
[SIGNAL NAME]
[MEMORY NO.]
[BACKUP INPUT STATUS]
[NUMBER OF REGISTERED
SIGNAL]
[COOLING CONDITION]
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS]
[AC VOLTAGE]
[LENS TYPE]
*2
[LENS ID]
*2
[LENS NAME]
*2
[LENS THROW RATIO]
[LENS ZOOM TYPE]
[ZOOM CALIBRATION]
[ON COUNT]
[OPERATING MODE]
[NORMAL]
[ECO]
[USER1]
[USER2]
[USER3]
[CONSOLIDATED RUNTIME]
[UPGRADE KIT]
[SLOT1]
[SLOT2]
186 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
Displays the serial number of the projector.
Displays the runtime of the projector.
Displays the runtime of the light source 1 and the light source 2.
Displays the elapsed time from when the light source is illuminated.
The elapsed time after the illumination of the light source can be confirmed when adjusting the focus.
The elapsed time is reset when the light source is temporarily turned off such as using the shutter
function.
Displays the main and sub versions of the firmware of the projector.
Displays the status of the intake air temperature of the projector.
*1
Displays the status of the internal temperature of the projector.
*1
Displays the status of the exhaust air temperature of the projector.
*1
Displays the light source 1 temperature status of the projector.
Displays the light source 2 temperature status of the projector.
Displays the status of the projector.
Displays the input terminal currently selected.
Displays the representative input terminal when one image is displayed with multiple input signals.
Displays the input signal name.
Displays the memory number of the input signal.
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 125)
Displays the number of registered signals.
Displays the set cooling conditions.
Displays the control status of the REMOTE2.
Displays the input supply voltage.
Displays the type name (type of the projection lens) set to the projection lens.
Displays the ID set to the projection lens.
Displays the name set to the projection lens.
Displays the range of throw ratio supported by the projection lens in accordance with the [LENS
*2
TYPE] setting.
Displays the drive method of the zoom motor attached to the projection lens.
*2
Displays the zoom calibration result ([OK]/[FAILED]) and the calibration date.
*2
[POWER ON TIMES]
[MECHANICAL SHUTTER]
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
Displays the runtime of the light source with [OPERATING MODE] set to [ECO].
Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
Displays the runtime of the light source with [OPERATING MODE] set to [USER2].
Displays the runtime of the light source with [OPERATING MODE] set to [USER3].
Converts the total runtime of the light sources with [OPERATING MODE] set to each item into the
time used with the [NORMAL] setting.
*3
The converted runtime is used for a rough indication about when to perform maintenance when the
projector is used in combination of each item in [OPERATING MODE].
[ET-UK20]
[ET-CUK10]
Displays the product model number of the Interface Board installed in <SLOT 1>.
Also, the firmware version is displayed after the product model number.
Displays the product model number of the Interface Board installed in <SLOT 2>.
Also, the firmware version is displayed after the product model number.
Displays the number of times the power is turned on.
Displays the number of times the mechanical shutter is closed.
It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].
Displays the activation status by the Upgrade Kit (Model No.:
ET-UK20).
Displays the activation status by the Auto Screen Adjustment
Upgrade Kit (Model No.: ET-CUK10).
Advertisement
Table of Contents
