Can-Am OUTLANDER 6x6 T 2021 Series Operator's Manual
  1. Manuals
  2. Brands
  3. Can-Am Manuals
  4. Motorcycle
  5. OUTLANDER 6x6 T 2021 Series
  6. Operator's manual

Can-Am OUTLANDER 6x6 T 2021 Series Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OUTLANDER
6x6 T
TM
Series
WARNING
Read this guide thoroughly.
It contains important safety information.
Minimum recommended age: Operator: 16 years old.
Keep this Operator's Guide in the vehicle.
2 1 9 0 0 2 0 9 1
Original Instructions

Advertisement

Table of Contents
loading

Related Manuals for Can-Am OUTLANDER 6x6 T 2021 Series

Summary of Contents for Can-Am OUTLANDER 6x6 T 2021 Series

  • Page 1 OUTLANDER 6x6 T Series WARNING Read this guide thoroughly. It contains important safety information. Minimum recommended age: Operator: 16 years old. Keep this Operator’s Guide in the vehicle. 2 1 9 0 0 2 0 9 1 Original Instructions...
  • Page 2 Take time to familiarize yourself with your new vehicle. The following trademarks are the property of Bombardier Recreational Products Inc.: In Finland, products are distributed by BRP Finland Oy. ® ® Can-Am D.E.S.S.™ DPS™ Outlander™ Rotax TTI™ XPS™...

  • Page 3: I Vehicle Identification

    TYPICAL - VIN LABEL - UNDER THE SEAT loss. These numbers are also required by the authorized Can-Am dealer to complete warranty claims properly. No warranty will be allowed by BRP if...

  • Page 4: Vehicle Identification Form

    I VEHICLE IDENTIFICATION 2) Vehicle Identification Form Please verify with your dealer to ensure your vehicle has been registered with BRP. _______________...

  • Page 5: Engine Identification Number (Ein)

    IMPORTANT ximum load label, refer to ON-PRODUCT LABELS . The Can-Am T Series tractor can tow a trailer on the road. Check the maximum allowable load of the trailer. Check the regula- tions for your area regarding the use of a tractor and trailer on the road.

  • Page 6: Foreword

    II FOREWORD OPERATOR'S GUIDE 2021 T Category (EU) Reg.167/2013 Outlander 6x6 XU+ 650 T category Outlander 6x6 XU+ 1000 T category Outlander 6x6 MAX XU+ 650 T category Outlander 6x6 MAX XU+ 1000 T category Outlander 6x6 MAX XT 650 T category Outlander 6x6 MAX XT 1000 T category Dieses Handbuch ist möglicherweise in Ihrer Landessprache Deutsch...

  • Page 7: Know Before You Go

    ® Never operate this vehicle without BRP warranty and a network of autho- proper instruction. Take a training rized Can-Am dealers ready to provide course. All operators should receive the parts, service or accessories you training from a certified instructor.
  • Page 8 II FOREWORD If you have any question regarding any change specifications, designs, fea- topic whether or not it is covered in this tures, models or equipment without CONTACT Operator's Guide, refer to incurring any obligation upon itself. This Operator's Guide should remain If you need more information, please with the vehicle when it is sold.

  • Page 9: Table Of Contents

    TABLE OF CONTENTS I VEHICLE IDENTIFICATION ............1 1) Vehicle Identification Number .
  • Page 10 TABLE OF CONTENTS I CONTROLS (cont’d) 3) Brake Lock ..............87 4) Brake Pedal .
  • Page 11 TABLE OF CONTENTS VII SPECIAL PROCEDURES (cont’d) 2) What to Do if Water is in the Air Filter Housing ......119 3) What to Do if Vehicle is Turned Over ........120 4) What to Do if Vehicle is Immersed in Water..
  • Page 12 G) WARRANTY ® BRP LIMITED WARRANTY USA AND CANADA: 2021 CAN-AM ATV ..184 US EPA EMISSION-RELATED WARRANTY ........187 BRP INTERNATIONAL LIMITED WARRANTY: 2021 CAN-AM ATV .

  • Page 13: A) Safety Information

    A) SAFETY INFORMATION ________ _______ A) SAFETY INFORMATION...

  • Page 14: I General Precautions

    I GENERAL PRECAUTIONS 1) Avoid Carbon – For refueling, strictly adhere to in- FUEL structions in Monoxide Poisoning – Never start or operate the engine if All engine exhaust contains carbon the fuel cap is not properly installed. monoxide, a deadly gas. Breathing car- bon monoxide can cause headaches, Gasoline is poisonous and can cause dizziness, drowsiness, nausea, confu-...

  • Page 15: Special Safety Messages

    II SPECIAL SAFETY MESSAGES THIS VEHICLE IS NOT A TOY AND CAN BE HAZARDOUS TO OPERATE. – This vehicle handles differently from other vehicles including motorcycles and cars. A collision or rollover can occur quickly, if you fail to take proper precautions, even during routine maneuvers such as turning and driving on hills or over obstacles.
  • Page 16 II SPECIAL SAFETY MESSAGES – Always check for obstacles before operating in a new area. Never attempt to operate over large obstacles, such as large rocks or fallen trees. Always follow RIDING proper procedures when operating over obstacles as described in TECHNIQUES in this Operator's Guide.
  • Page 17 II SPECIAL SAFETY MESSAGES – Inform the passenger concerning the basic rules for a safe ride. – Instruct the passenger to read the vehicle’s safety labels and to watch the SAFETY VIDEO – Always practice the maneuvers described in this Operator's Guide without and with a passenger.

  • Page 18: European Community

    II SPECIAL SAFETY MESSAGES 1) European Community On Road Use The followings warnings applies only in the European Countries where on road us- age is allowed. SEVERE INJURY OR DEATH can result if you do not comply with the following instructions. WARNING –...

  • Page 19: Operation Warnings

    Beginners and inexperienced operators should complete a training course. They should then regularly practice the skills learned during the course as well as the operating techniques described in this Operator's Guide. For more information about a training course, contact an authorized Can-Am dealer. ________ _______ A) SAFETY INFORMATION...
  • Page 20 III OPERATION WARNINGS WARNING V00A1AQ POTENTIAL HAZARD Failure to follow the age recommendations for this vehicle. WHAT CAN HAPPEN A lack of respect for this age recommendation can lead to severe injury or death of the child. Even though a child may be within the age group for which this vehicle is recommended, he may not have the skills, abilities, or judgment needed to operate this vehicle safely and may be involved in a serious accident.
  • Page 21 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to respect the physical limitations of the passenger on 2-UP models. WHAT CAN HAPPEN A passenger that cannot completely lean his feet on footrests can be ejected when riding on uneven terrain. HOW TO AVOID THE HAZARD The passenger must be capable of keeping his feet on the footrests and his hands on grab handles at all times when he is seated on the vehicle.
  • Page 22 III OPERATION WARNINGS 2-UP Models Only WARNING POTENTIAL HAZARD Carrying more than one (1) passenger on this vehicle. WHAT CAN HAPPEN Carrying more than one (1) passenger reduces your ability to balance and control this vehicle. Could cause an accident, resulting in harm to you and/or your passengers. HOW TO AVOID THE HAZARD Never carry more than one (1) passenger.
  • Page 23 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Allowing passenger(s) to sit on front or rear racks on this vehicle. WHAT CAN HAPPEN Allowing a passenger could: – Impair vehicle stability which could lead to a loss of control. – Result in injury to passenger(s) from impact on hard surfaces. –...
  • Page 24 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle on paved surfaces. WHAT CAN HAPPEN Paved surfaces may seriously affect handling and control of the vehicle, and may cause the vehicle to go out of control. HOW TO AVOID THE HAZARD If a road usage is allowed in your area, operate your vehicle on paved sur- faces only for short distance and for the only purpose of moving the vehicle from an off-road usage to another.
  • Page 25 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Riding this vehicle without wearing an approved helmet, eye protection and protective gear. On 2-UP models, passenger should also have an approved helmet with a rigid chin guard. WHAT CAN HAPPEN – Riding without an approved helmet increases the chances of a severe head injury or death in the event of an accident.
  • Page 26 III OPERATION WARNINGS WARNING V00A07Q POTENTIAL HAZARD Using this vehicle with drugs or alcohol. WHAT CAN HAPPEN Could cause the passenger to fall off (2-UP models). Could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death.
  • Page 27 III OPERATION WARNINGS WARNING V00A08Q POTENTIAL HAZARD Operating this vehicle at excessive speeds. WHAT CAN HAPPEN Increases your chances of losing control of the vehicle, which can result in an accident. HOW TO AVOID THE HAZARD Always travel at a speed which is appropriate for the terrain, visibility and operating conditions, and your experience.
  • Page 28 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Attempting wheelies, jumps and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, for the operator and the passenger (2-UP models), including an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps. Do not try to show off. WARNING POTENTIAL HAZARD Failure to inspect the vehicle before operating.
  • Page 29 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Riding on frozen waterways. WHAT CAN HAPPEN Breaking through the ice can lead to severe injury or death. HOW TO AVOID THE HAZARD Never ride this vehicle on a frozen surface before you are sure the ice is thick enough and sound enough to support the vehicle and its load, as well as the force that is created by a moving vehicle.
  • Page 30 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to use extra care when operating this vehicle on unfamiliar terrain. WHAT CAN HAPPEN You can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning, passenger ejection (2-UP models) or loss of control.
  • Page 31 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an acci- dent, including an overturn or passenger ejection (2-UP models). HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control this vehicle on...
  • Page 32 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Turning improperly. WHAT CAN HAPPEN Vehicle could go out of control, causing a collision or an overturn or a pas- senger ejection (2-UP models). HOW TO AVOID THE HAZARD Always follow proper procedures for turning as described in this Operator's Guide.
  • Page 33 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating on excessively steep hills. WHAT CAN HAPPEN The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. HOW TO AVOID THE HAZARD Never operate this vehicle on hills too steep for the vehicle or for your abili- ties.
  • Page 34 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Climbing hills improperly. WHAT CAN HAPPEN Could cause loss of control, passenger ejection (2-UP models) or cause ve- hicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for climbing hills as described in this Op- erator's Guide.
  • Page 35 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Going down a hill improperly. WHAT CAN HAPPEN Could cause loss of control, passenger ejection (2-UP models) or cause ve- hicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for going down hills as described in this Operator's Guide.
  • Page 36 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly crossing hills or turning on hills. WHAT CAN HAPPEN Could cause loss of control, passenger ejection (2-UP models) or cause ve- hicle to overturn. HOW TO AVOID THE HAZARD Never attempt this maneuver on 2-UP models when the passenger is on board.
  • Page 37 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Stalling, rolling backwards or improperly dismounting while climbing a hill. WHAT CAN HAPPEN Could result in vehicle overturning. HOW TO AVOID THE HAZARD Use low gear and maintain steady speed when climbing a hill. Switch 6x6 If you lose all forward speed: Operator and passenger (2-UP models) must keep their weig ht uphill.
  • Page 38 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly operating over obstacles. WHAT CAN HAPPEN Could cause loss of control (passenger ejection on 2-UP models), or a colli- sion. Could cause the vehicle to overturn. HOW TO AVOID THE HAZARD Before operating in a new area, check for obstacles. Never attempt to ride over large obstacles, such as large rocks or fallen trees.
  • Page 39 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Skidding or sliding improperly. WHAT CAN HAPPEN You may lose control of this vehicle. You may also regain traction unexpectedly, which may cause the vehicle to overturn or passenger ejection (2-UP models). HOW TO AVOID THE HAZARD Learn to safely control skidding or sliding by practicing at low speeds and on level smooth terrain.
  • Page 40 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle through deep or fast flowing water. WHAT CAN HAPPEN Tires may float, causing loss of traction and loss of control, which could lead to an accident. HOW TO AVOID THE HAZARD Never operate this vehicle in fast flowing water or in deep water.
  • Page 41 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly operating in reverse. WHAT CAN HAPPEN You could hit an obstacle or person behind the vehicle, resulting in serious injury. HOW TO AVOID THE HAZARD When you select reverse gear, make sure there are no obstacles or people behind the vehicle.
  • Page 42 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle with improper tires, or with improper or uneven tire pressure. WHAT CAN HAPPEN Use of improper tires on this vehicle, or operation of this vehicle with improper or uneven tire pressure, may cause loss of control, tire blow outs, tire to move around on its rim, and increases the risk of an accident.
  • Page 43 All parts and accessories added to this vehicle should be approved by BRP and should be installed and used according to instructions. If you have questions, consult an authorized Can-Am dealer. NEVER install a passenger seat (1-UP models) or use the racks to carry a passenger.
  • Page 44 III OPERATION WARNINGS WARNING POTENTIAL HAZARD Overloading this vehicle, carrying or towing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle handling which could lead to an accident. HOW TO AVOID THE HAZARD Never exceed the stated load capacity for this vehicle including operator and passenger (2-UP models) as well as other loads and added accessories.
  • Page 45 III OPERATION WARNINGS WARNING V03M01Q POTENTIAL HAZARD Transporting flammable or dangerous material can lead to explosions. WHAT CAN HAPPEN This can cause serious injury or death. HOW TO AVOID THE HAZARD Never transport flammable or dangerous material. ________ _______ A) SAFETY INFORMATION...

  • Page 46: Riding The Vehicle

    Please take the time to study this Operator's Guide and all on-product safety labels SAFETY VIDEO as well as the located at https://can-am.brp.com/off-road/safety. They more completely describe what you should know about this vehicle before riding it. Whether you are a new user or an experienced rider, it is important for your personal safety that you know the controls and features of this vehicle.

  • Page 47: Pre-Ride Inspection

    Correct any problem that you discover to reduce the risk of a breakdown or crash. See an authorized Can-Am dealer as necessary. Before using this vehicle, the operator should always perform the following pre-ride inspection check list.
  • Page 48 IV RIDING THE VEHICLE Pre-Ride Inspection Check List What to Do Before Starting the Engine (Key OFF) ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Engine oil Check engine oil level. Coolant Check coolant level. Brake fluid Check brake fluid level. Leaks Check for any leaks under vehicle Activate throttle lever several times to ensure it operates...
  • Page 49 IV RIDING THE VEHICLE ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Chassis and Check underneath vehicle for any debris on chassis or suspension suspension and clean them properly Engine air filter Inspect and clean engine air filter CVT air filter Inspect and clean CVT air filter What to Do Before Starting the Engine (Key ON) ITEMS TO BE...

  • Page 50: Riding Gear

    IV RIDING THE VEHICLE What to Do After the Engine is Started ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Check if steering operates freely by completely turning it Steering from side to side Shift lever Check operation of shift lever (P, R, N, H and L) 4WD/6WD selector Check operation of 4WD/6WD selector Drive forward slowly a few feet and apply brake lever...

  • Page 51: Carrying A Passenger

    IV RIDING THE VEHICLE Approved helmet Eye protection Rigid chin guard Chest protector Long sleeves Gloves Long, sturdy pants Boots V00A0RN 3) Carrying a Passenger 1 1 -UP Models This vehicle is designed to carry ONE (1) operator only. Do not install passenger seats or use the racks to carry a passenger.

  • Page 52: Environment

    IV RIDING THE VEHICLE users on the trail. Do not drive to the center of the trail and do not zigzag to one side of the trail then the other. Be prepared to stop or pull off to the side if another trail user appears in front of you.

  • Page 53: Design Limitation

    IV RIDING THE VEHICLE Respect farm lands. Always obtain the permission of the landowner before riding on private land. Respect crops, farm animals and property lines. If you come to a closed gate, close it again behind you. Finally, do not pollute streams, lakes or rivers and do not modify the engine or ex- haust system, or remove any of its components.
  • Page 54 IV RIDING THE VEHICLE on the foot pegs at all times. Do not direct your toes outwards nor extend your feet out to assist in turning as they can be hit or be snagged on passing obstacles, or may come into contact with the wheels. Even though there is a suspension on this vehicle, there are “washboard”...
  • Page 55 IV RIDING THE VEHICLE Turning Practice turning at low speeds before attempting to turn at faster speeds. Keep both hands on handlebars and feet on foot pegs. Maintain a constant speed or a slight acceleration during turn. To reduce the risk of rollovers: –...
  • Page 56 IV RIDING THE VEHICLE Practice braking to get familiar with the brake response. – Do it at low speed first, then increase the speed. – Practice braking in straight line at different speeds and different braking force. – Practice emergency braking; optimal braking is obtained in straight line, with high force applied, without locking the wheels.
  • Page 57 IV RIDING THE VEHICLE Uphill Driving 1-UP Models Before trying to climb a hill, keep these things in mind. Hill Climbing should only be attempted by experienced operators. Start on shallow slopes. Always drive straight uphill and keep your body weight forward towards the top of the hill. Keep your feet on the footrests, shift your ATV into a lower gear and accelerate before you start to climb.
  • Page 58 IV RIDING THE VEHICLE too steep to safely stop or recover from after an unsuccessful climbing attempt. Try to avoid steep inclines. If you're not careful, you could tip over when going up hills. If the hill is too steep and you cannot proceed or the vehicle begins to roll backwards, apply the brake, put the parking brake on, being careful not to slide.
  • Page 59 IV RIDING THE VEHICLE sfvmo2014-012-523 2 2 -UP Models The operator is responsible for the safety of the passenger; in doubt, disembark the passenger before proceeding. Always remember that the vehicle handling, stability and braking distance may be affected when riding with a passenger. The passenger must synchronize his movements with the operator.
  • Page 60 IV RIDING THE VEHICLE WARNING Be careful when loading and transporting liquid reservoirs. They can affect vehicle stability when side hilling by pulling downhill and increasing the risk of a roll over. vmo2012-012-527 2 2 -UP Models The passenger must synchronize his movements with the operator. The passen- ger must remain seated at all times.
  • Page 61 IV RIDING THE VEHICLE sfvmo2014-012-524 Wet brakes will affect the braking ability of your vehicle. Make sure you dry the brakes by applying them several times after the vehicle leaves the water, mud or snow. Allow greater distance for braking. Mud or marsh lands may be encountered near water.
  • Page 62 IV RIDING THE VEHICLE This will possibly result in a straight line slide of the vehicle. Again, the best advice is to safely reduce speed in anticipation of a maneuver so to give yourself time and distance to regain total vehicle control before it spins out of your control. As you drive your ATV over a loose snow covered surface, snow dust will be picked up in the wake turbulence of the moving vehicle and transported to contact and accumulate or melt on some exposed components including rotating parts...
  • Page 63 IV RIDING THE VEHICLE Riding on Loose Stones Riding on loose stones or gravel is very similar to riding on ice. They will affect the steering of vehicle possibly causing it to slide or tip over especially at high speeds (resulting in operator and passenger ejection (2-UP models).

  • Page 64: Moving Loads And Doing Work

    Your vehicle can help you perform a number of different LIGHT tasks ranging from snow removal to pulling wood or carrying cargo. A variety of accessories are avail- able from your authorized Can-Am dealer. To prevent possible injury, follow the in- structions and warnings that accompany the accessory. Always respect the load limits of the vehicle.
  • Page 65 V MOVING LOADS AND DOING WORK The following are examples of weight of model variations: EXAMPLES OF ACCESSORY PACKAGE WEIGHT MODEL WEIGHT Flat bed 0 kg (0 lb) Side wall 15 kg (33 lb) 35 kg (77 lb) Cargo Farmer 50 kg (110 lb) The following are examples of suitable total vehicle load distribution: EXAMPLE OF SUITABLE VEHICLE TOTAL LOAD...
  • Page 66 V MOVING LOADS AND DOING WORK Ensure no cargo protrudes outside the WARNING cargo rack and that cargo will not inter- Never overload, tow or carry cargo fere with your visibility or control of the improperly. Safely reduce speed vehicle. according to terrain conditions NOTICE when carrying cargo or pulling a...
  • Page 67 V MOVING LOADS AND DOING WORK Please note that the maximum total REAR CARGO LOAD ALLOWED is 318 kg (700 lb). This includes the rear cargo bed, rear storage compartment and tongue load. Operating While Carrying a Load Reduce your speed when carrying cargo and turn gradually.

  • Page 68: Hauling A Load

    Check the maximum axle loads of the frame junction when lowering vehicle identification plate (statutory cargo bed. plate). Can-am T series tractor can tow – Ensure to properly latch the a trailer on the road. Check the trailer, Cargo bed before riding.
  • Page 69 V MOVING LOADS AND DOING WORK and when a passenger 2-UP models) is on board. Be careful not to skid or slide. Improperly loading a trailer may cause loss of control. Respect the recom- mended maximum towing capacity and maximum tongue capacity (Re- CARRYING LOADS fer to ).

  • Page 70: Important On-Product Labels

    If missing or damaged, they can be replaced free of charge. sfvmo2012-012-004_a See an authorized Can-Am dealer. The following labels are on your ve- hicle, and they should be considered permanent parts of the vehicle. They need to be clean, visible and legible at all times.
  • Page 71 VI IMPORTANT ON-PRODUCT LABELS sfvmo2014-020-003_b 219002091-002 sfvmo2014-020-004_a sfvmo2014-002-037_a sfvmo2014-020-005_a sfvmo2014-020-001_a ________ _______ A) SAFETY INFORMATION...
  • Page 72 – Never carry a passenger. – Never use with drugs or alcohol. 704905679 Safety Video EN-704905679-DEC LABEL 2 https:// L L abel 3 can-am.brp.com /off-road/safety NOTICE Stop the vehicle and ap- ply the brake before using the shift lever. Patent : www.brp.com/en/about-brp/patents.html EN-704908489-DEC...
  • Page 73 VI IMPORTANT ON-PRODUCT LABELS Label 4 WARNING – NEVER carry a passenger on this carrier. – MAXIMUM FRONT LOAD: 45 kg (100 lb) evenly distributed. < 45 kg (100 lb) 704906105 EN-704906105-DEC LABEL 4 L L abel 5 WARNING – Locate and read operator's guide.
  • Page 74 VI IMPORTANT ON-PRODUCT LABELS Label 6 WARNING Pinch point. Keep clear when low- ering cargo bed. 704904236 LABEL 6 L L abel 7 This warning applies only in European Countries where on road usage is allowed. On Road Use This vehicle is built for "OFF ROAD" purposes only. It may be used for short distances on paved surfaces at reduced speed, in order to move the vehicle from an off road location to another.
  • Page 75 VI IMPORTANT ON-PRODUCT LABELS Label 8 WARNING – Locate and read operator's guide. Improper tire pressure or overloading can cause loss of control, resulting in SEVERE INJURY or DEATH. – ALWAYS maintain proper tire pressure as shown. – NEVER exceed the load capacity of 460 kg (1015 lb) including weight of operator, passenger, cargo, accessories, and trailer tongue weight.
  • Page 76 VI IMPORTANT ON-PRODUCT LABELS Label 9 WARNING – Locate and read operator's guide. Overloading can cause loss of control, resulting in SEVERE INJURY or DEATH. – NEVER exceed the load capacity of 460 kg (1,015 lb) including weight of operator, passenger, cargo, accessories, and trailer tongue weight. –...
  • Page 77 VI IMPORTANT ON-PRODUCT LABELS Label 10 WARNING – Locate and read operator's guide. – NEVER carry a passenger on this carrier. – Remove containers from vehicle before fueling. – Secure locking handles using the hairpin clip 704904227 704904227 LABEL 10 ________ _______ A) SAFETY INFORMATION...
  • Page 78 VI IMPORTANT ON-PRODUCT LABELS Label 11 L L abel 12 WARNING WARNING – NEVER sit on Cargo bed – SECURE with hairpin clip the re- lease handle. – ALWAYS pull a load using the trailer hitch or winch. 704904234 LABEL 12 704904228 704904228 LABEL 11...
  • Page 79 VI IMPORTANT ON-PRODUCT LABELS Label 13 WARNING – Open glove box cover and turn latch to the unlock position. Align and insert glove box latching system into the vehicle's "LINQ" opening. Turn latch to the lock position. Close cover and verify if glove box is locked in position.
  • Page 80 VI IMPORTANT ON-PRODUCT LABELS Label 14 L L abel 15 WARNING WARNING NEVER attach here or on the lug- – NEVER sit on tailgate gage rack to pull a load This can – NEVER exceed the load capacity cause the vehicle to tip over. AL- of 100 kg (220 lb)on tailgate WAYS use the trailer hitch to pull a load.
  • Page 81 VI IMPORTANT ON-PRODUCT LABELS Label 16 WARNING NEVER carry a load on top of the cover. 704904235 LABEL 16 ________ _______ A) SAFETY INFORMATION...
  • Page 82 VI IMPORTANT ON-PRODUCT LABELS Label 17 WARNING – Do not load longer than 1 250 mm (4 ft) – Do not load higher than the top side support – Always back the load to the front wall – Always make sure the load is secured to the vehicle EN-704904408-DEC LABEL 17 L L abel 18...

  • Page 83: Compliance Labels

    VI IMPORTANT ON-PRODUCT LABELS 2) Compliance Labels Label 20 WARNING Do not stand here. 55R - 01 4134 D=5.53kN S=67.5kg CLASS A50-X EN-704906367-DEC ON TRAILER HITCH Category 1 - The cab does not offer any protection against substances which are harmful to health. 704906301 EN-704906301-DEC 704904368...

  • Page 84: Technical Information Labels

    VI IMPORTANT ON-PRODUCT LABELS 3) Technical Information Labels 707800373 UNDER SEAT NOTICE Stop the vehicle and ap- ply the brake before using the shift lever. EN-704906894-DEC NEAR SHIFT LEVER STOP EN-704908379-DEC vmo2015-023-500_a TYPICAL _______ _______ A) SAFETY INFORMATION...
  • Page 85 VI IMPORTANT ON-PRODUCT LABELS 704904229 704904229 LABEL 1 704904230_231 LABELS 2 AND 3 ________ _______ A) SAFETY INFORMATION...
  • Page 86 VI IMPORTANT ON-PRODUCT LABELS 704906395-DEC ON BRAKE FLUID RESERVOIRS EN-704906895-DEC ON FRONT SUSPENSION ARMS EN-704906896-DEC ON REAR SUSPENSION ARMS EN-704907067-DEC ON SIDE OF CHASSIS - FRONT AND REAR Refer to INSTRUCTIONS FOR VEHICLE LIFTING section in your OPERATOR'S GUIDE for lifting points locations and procedure. _______ _______ A) SAFETY INFORMATION...

  • Page 87: B) Vehicle Information

    B) VEHICLE INFORMATION _______________...

  • Page 88: I Controls

    I CONTROLS 219002091-101 TYPICAL ______________...

  • Page 89: Throttle Lever

    I CONTROLS 1) Throttle Lever The throttle lever is located on the RH side of the handlebar. It can be posi- tioned to be activated with the thumb or finger. The throttle lever controls the engine speed. To increase or maintain vehicle speed, press the throttle lever.

  • Page 90: Brake Pedal

    I CONTROLS 219001872-001_a Step 1: Apply brakes Step 2: Lock brakes vmo2012-012-015_a 1. Brake pedal NOTE: The lock lever can be set to in several positions. When released, the brake pedal should return to its original position. NOTICE Ensure when the brake Braking effect is proportional to the lock is applied that the vehicle stays force applied on the pedal.

  • Page 91: Multifunction Switch

    Can-Am vehicle, each can nition switch must be in the "ON with be programmed by your authorized lights" or "ON" position and the engine Can-Am dealer to accept the other ve- stop button set to ON (up). hicle D.E.S.S. keys. Engine Stop Switch This switch can be used to stop the en- gine and as an emergency control.
  • Page 92 I CONTROLS To stop engine, set the engine stop Override/DPS Button switch to the STOP position. Depending on the vehicle model, this button can have 3 functions. 219001868_011_c 219001868_011_e Hazard Lights Switch Override Function The override switch main function is to bypass the engine speed limiter in re- verse operation by allowing maximum engine torque.

  • Page 93: Shift Lever

    I CONTROLS NOTE: When using the override func- To stop the turn signals, move the tion, the gauge will scroll an OVER- switch back to the middle position. RIDE message to confirm that the function is activated. 3. To disengage the override function, simply release the override button.
  • Page 94 I CONTROLS The shift lever has 5 positions: WARNING When driving downhill in reverse, SHIFT LEVER POSITIONS gravity can increase the vehicle POSITION GEAR speed above the set limited re- verse speed. Park Reverse Neutral Neutral The neutral position disengages the gearbox.

  • Page 95: Lh Handlebar Switches (If Equipped)

    I CONTROLS 8) LH Handlebar Switches NOTICE vehicle must stopped to engage or disengage (If Equipped) 4WD/6WD switch. Mechanical dam- age may occur if switch is engaged or disengaged while driving. The 6WD mode is engaged when the switch is pushed downwards. 219001854-002_a 1.
  • Page 96 I CONTROLS 219001964-001_d 219001964-001_e The SPORT mode provides a crisper throttle response. Press right to acti- vate and left to deactivate. NOTE: The SPORT mode can be acti- vated with all key types and provides the maximum power with the used key.

  • Page 97: Digital Display

    4.5" DIGITAL DISPLAY Multifunction Display Left Lateral Display Lower Display 219001961-711 The left lateral display includes: 219001961-710 – Fuel level indicator May display the following: – 4X6 / 6X6 telltale – RPM – Speed – Engine Temperature – Battery Voltage –...

  • Page 98: Warning Lamps And Indicators

    4.5" DIGITAL DISPLAY Central Display The MODE display indicates the se- lected mode of operation: – SPORT – WORK A message of the selected mode will be displayed on the lower display at activation and deactivation as follow: MESSAGE DRIVE MESSAGE AT MODE DEACTIVATION...

  • Page 99: Settings

    4.5" DIGITAL DISPLAY NOTE: Some warning indicators ap- Icons and Indicators - Multifunction pear in the display of the multifunction Display gauge and function the same as an in- ICONS AND INDICATORS dicator lamp but do not display when starting the vehicle. Denotes SPORT mode is selected.
  • Page 100 4.5" DIGITAL DISPLAY throttle is fully depressed, at that time, the speed limiter will be temporary deactivated (the icon will be blinking) until vehicle speed is under or equal the speed limiter's set point. As you proceed under a constant speed setting, keep your attention level up to maintain good situational awareness.
  • Page 101 (minutes flash). 8. Press LOWER (MENU) button to ac- knowledge minutes. Setting Language The gauge display language can be changed. Refer to an authorized Can-Am dealer for language availability and to setup the gauge to your prefer- ence. _______________...

  • Page 102: Equipment

    III EQUIPMENT 219002091-100 TYPICAL - 2-UP MODEL SHOWN ______________...

  • Page 103: Operator's Seat

    III EQUIPMENT 1) Operator's Seat WARNING The seat is designed for an operator Confirm that the operator's seat only. is properly locked in position by pulling back and up several times. WARNING Never allow anyone to seat as a 2) Passenger's Seat passenger on the operator's seat.

  • Page 104: Footpegs

    III EQUIPMENT Passenger's Seat Removal WARNING 1. To unlock latch, pull the passenger's It is of the upmost importance for seat latch lever toward the front of the passenger's safety that you the seat. confirm that the passenger's seat is properly locked in position by pulling back and up several times.

  • Page 105: Rear Storage Compartment

    III EQUIPMENT To Open Rear Storage Compartment To Open Storage Compartment Hatch Unlatch storage compartment hatch. vmo2012-012-018_a TYPICAL 1. 12 V power outlet Remove protective cap to use. Always reinstall it after use to protect against weather. sfvmo2014-012-023_c 5) Rear Storage PULL LATCHES UPWARDS 1.

  • Page 106: Front Cargo Rack And Glove Box

    III EQUIPMENT vmo2015-023-504 FRONT CARGO RACK vmr2015-146-001_a To Close Rear Storage WARNING Compartment – Never carry a passenger on a To Close Storage Compartment cargo rack. Hatch – Cargo must never interfere with the drivers line of sight or affect Gently pull, lift and push hatch into his ability to properly steer the place.

  • Page 107: Trailer Hitch

    III EQUIPMENT 2. Align and insert glove box latching system into the vehicle's "LINQ" opening. sfvmo2014-001-005_a 1. Latch 3. Remove glove box. 7) Trailer Hitch Convenient hitch to install a ball to tow a trailer or other equipment. Use only sfvmo2014-001-004_a the ball type hitch certified by BRP.

  • Page 108: Tool Kit

    III EQUIPMENT When a trailer is connected and the For such work you should contact your turn signals or hazard lights are in func- dealer who has specially trained per- tion, an indicator lamp located on the sonnel to help you. INDI- handlebar cover, blinks.

  • Page 109: Roller Fairlead

    III EQUIPMENT 10) Roller Fairlead The roller fairlead is used to prevent damages to the vehicle and guide the cable into the winch. sfvmo2014-001-020_a 1. Cargo bed release handle 2. Hairpin clip To Lower the Cargo Bed 219001733-002_a 1. Winch To lower the Cargo bed, simply push it 2.

  • Page 110: Heated Throttle Lever (If Equipped)

    III EQUIPMENT 219001854-002_c 219001854-002_e 1. Heated grips switch 1. Heated throttle lever switch Press the switch again to increase the Press the switch again to increase the heat level. Each time the switch is heat level. Each time the switch is pressed, the heat level increases.

  • Page 111: Iiia Equipment (If Available On Your Model)

    IIIa EQUIPMENT (IF AVAILABLE ON YOUR MODEL) 1) Flat Bed Side Walls and Tailgate Removal sfvmo2014-001-006 2) Front LinQ Rack sfvmo2014-001-012_a 1. Side wall 2. Tailgate 1. Open tailgate latches on both sides. sfvmo2014-001-030_a 1. Front LinQ rack Align and insert Front LinQ rack into the sfvmi2014-018-006_a vehicle's "LINQ"...
  • Page 112 IIIA EQUIPMENT (IF AVAILABLE ON YOUR MODEL) sfvmi2014-018-004_b sfvmi2014-018-010_a 4. Remove locking handles on both 7. Place locking handles in their origi- sides. nal position. sfvmi2014-018-002_a sfvmi2014-018-008_a 5. Lift side wall up and remove it. 8. Secure with hairpin clip. Repeat on the other side.
  • Page 113 IIIA EQUIPMENT (IF AVAILABLE ON YOUR MODEL) sfvmi2014-018-001_b sfvmi2014-018-007 2. Remove locking handles. 5. Secure with hairpin clip. sfvmi2014-018-008_b sfvmi2014-018-004 6. Install tailgate. 3. Place side wall on flat bed and lower it on its place. Repeat on the other side. sfvmi2014-018-009 WARNING sfvmi2014-018-003_b...

  • Page 114: Farmer

    IIIA EQUIPMENT (IF AVAILABLE ON YOUR MODEL) Tailgate Extension Removal sfvmi2014-018-006_b WARNING Make sure you do not leave hands between latches and tailgate. sfvmo2014-001-014_a 4) Farmer 1. Cargo extension 1. Remove tail cargo extension secur- ing devices. 1.1 Remove screw securing cargo extension.
  • Page 115 IIIA EQUIPMENT (IF AVAILABLE ON YOUR MODEL) sfvmo2014-001-017_a sfvmi2014-018-005 3. Remove support brackets from tail- 3. Place support brackets to tailgate. gate. 3.1 Install support brackets. 3.1 Open tailgate latches. 3.2 Turn support brackets inward. 3.2 Turn support brackets to the 3.3 Close tailgate latches.
  • Page 116 IIIA EQUIPMENT (IF AVAILABLE ON YOUR MODEL) sfvmo2014-001-017_b sfvmo2014-001-021_a 1. Cargo extension 5. Install tail cargo extension. 5.1 Install bracket. 5.2 Place bracket. 5.3 Tighten cargo extension screw recommended torque. TIGHTENING TORQUE Cargo 8 N•m ± 1 N•m extension (71 lbf•in ± 9 lbf•in) screw sfvmo2014-001-019_a 1.

  • Page 117: Fuel

    IV FUEL 1) Fuel Requirements NOTICE Always use fresh gaso- line. Gasoline will oxidize; the re- sult is loss of octane, volatile com- pounds, and the production of gum NOTICE Never experiment with and varnish deposits which can other fuels. Engine or fuel system damage the fuel system.
  • Page 118 IV FUEL 4. Insert the spout into the filler neck. 5. Pour fuel slowly so that air can es- cape from the tank and prevent fuel flow back. Be careful not to spill fuel. 6. Stop filling when the fuel reaches the bottom of filler neck.

  • Page 119: Break-In Period

    V BREAK-IN PERIOD Operation During Break-In A break-in period of 300 km (200 mi) or 10 operating hours is required for the vehicle. Engine During the break-in period: – Avoid full throttle operation. – Maximum throttle should not ex- ceed 3/4. –...

  • Page 120: Basic Procedures

    VI BASIC PROCEDURES 1) Starting the Engine 3) Stopping the Engine and Parking the Vehicle The shift lever must be set to PARK or NEUTRAL. WARNING NOTE: For your convenience, an over- ride mode allows the engine to be Avoid parking on steep slope as started with the shift lever in any po- the vehicle may roll away.

  • Page 121: Special Procedures

    – Vents – CVT air filter cleaning NOTICE authorized – CVT cleaning Can-Am dealer to have the CVT in- spected and cleaned. – Fuel tank breather replacement – Lubricant inspection and replace- Reinstall the drain plug and secure it ment as required (engine, gearbox using the spring clamp.

  • Page 122: What To Do If Vehicle Is Turned Over

    Do not use: – Any electrical equipments – Winch (if equipped) It will be necessary to take the vehi- cle to an authorized Can-Am dealer as soon as possible. NEVER ATTEMPT TO START THE ENGINE! ______________...

  • Page 123: Tune Your Ride

    VIII TUNE YOUR RIDE WARNING Suspension adjustment could af- fect vehicle handling. Always take time to familiarize yourself with the vehicle's behavior after any suspension adjustment have been made. 1) Suspension Adjustment 529000035 SUSPENSION ADJUSTMENT TOOL Suspension adjustment and loading can have an effect on your vehicle han- dling and comfort.
  • Page 124 VIII TUNE YOUR RIDE changed when riding. These modes 2. Release DPS button. are used to set the level of assistance 3. Repeat until desired setting is se- to match each rider's preferences. lected. The following DPS modes are preset in NOTE: The DPS adjustment will not the vehicle.

  • Page 125: Transporting The Vehicle

    IX TRANSPORTING THE VEHICLE When contacting a towing or trans- SAFETY PRECAUTIONS porting service, be sure to ask if they Ensure you have a good have a flatbed trailer, loading ramp or Visibility visibility during the entire power ramp to safely lift the vehicle maneuver.

  • Page 126: Using A Winch To Pull Vehicle Onto Trailering Equipment

    IX TRANSPORTING THE VEHICLE 3. Back off the vehicle, verify ramps 3. If the vehicle is not equipped with a are still secure, then proceed at winch, proceed as follows: proper speed. 3.1 Attach strap to lower front 4. Carefully drive vehicle onto platform bumper anchor.

  • Page 127: Getting Vehicle Out Of Trailer

    IX TRANSPORTING THE VEHICLE vmo2013-007-014_a TYPICAL 1. Front tie-down point location vmo2013-007-003_a TYPICAL 1. Rear tie-down point location NOTICE Securing vehicle at other locations may damage the vehicle. 4) Getting vehicle out of trailer WARNING Vehicle may have moved during transport.

  • Page 128: Instructions For Vehicle Lifting

    INSTRUCTIONS FOR VEHICLE LIFTING General Safety WARNING Information for Lifting Ensure all wheels are locked be- fore lifting the vehicle. Do not ex- 1. Engage the 6WD mode. ceed the lifting device capacity. NOTE: 6WD mode is engaged when Use only a device approved for engine is running and vehicle has lifting this type of vehicle.
  • Page 129 INSTRUCTIONS FOR VEHICLE LIFTING 2. Secure the vehicle laterally using jack stands on the stabilization points. 219001870-003_a 1. Front of vehicle 2. Front lifting point 3. LH stabilization point 4. RH stabilization point 5. Rear lifting point 3. Lift the rear of the vehicle. 4.
  • Page 130 INSTRUCTIONS FOR VEHICLE LIFTING This page is intentionally blank ______________...
  • Page 131 C) MAINTENANCE ______________...

  • Page 132: I Maintenance Schedule

    Although an authorized Can-Am Off-Road dealer has an in-depth technical knowl- edge and tools to service your vehicle, the emission-related warranty is not condi- tioned on the use of an authorized Can-Am Off-Road dealer or any other establish- ment with which BRP has a commercial relationship.

  • Page 133: Maintenance Schedule

    I MAINTENANCE SCHEDULE 3) MAINTENANCE SCHEDULE Make sure to perform proper maintenance at recommended intervals as indicated in the tables. Some items of the maintenance schedule must be performed in function of the calendar, regardless of the distance or time of operation. EVERY 1 500 KM (1,000 MI) OR 50 HOURS (whichever comes first) EVERY 750 KM (500 MI) OR 25 HOURS (whichever comes first) Inspect and clean engine air filter.
  • Page 134 I MAINTENANCE SCHEDULE PERFORM AT THE FIRST 3 000 KM (2,000 MI) AND AT 6 000 KM (4,000 MI) THEN FOLLOW THE REGULAR SCHEDULE PERFORM AT THE FIRST 1 500 KM (1,000 MI) AND AT 3 000 KM (2,000 MI) THEN FOLLOW THE REGULAR SCHEDULE Replace gearbox oil Clean the vehicle speed sensor (VSS)

  • Page 135: Maintenance Procedures

    NOTE: An accessory pre-filter for basic maintenance procedures. If you "dusty conditions" may be used. Con- have the necessary mechanical skills tact an authorized Can-Am dealer for and the required tools, you can per- details. form these procedures. If not, see your authorized Can-Am dealer.
  • Page 136 II MAINTENANCE PROCEDURES vmr2012-010-017_a vmo2012-012-039_a TYPICAL - SOME PARTS REMOVED FOR 1. Air filter cover CLARITY 1. Air filter housing inlet drain tube Remove air filter. 3. Check air filter dirty chamber for cleanliness. – If any debris or water are found, clean air filter chamber using a vacuum cleaner.
  • Page 137 II MAINTENANCE PROCEDURES Air Filter Cleaning and Oiling CAUTION Always wear propriate skin and eye protection. Chemicals can cause a skin rash and eye injury. Paper Filter Cleaning 1. Ensure that the foam filter is re- vbs2009-012-005 moved from paper filter. TYPICAL - DRY 2.

  • Page 138: Engine Oil

    II MAINTENANCE PROCEDURES 5. Reinstall the foam filter over the pa- Then align and insert studs with grom- per filter. mets on rear portion of console until studs engage with grommets. vbs2009-012-001 TYPICAL 6. Slightly grease plastic body of filter for ease of installation and future re- moval.
  • Page 139 II MAINTENANCE PROCEDURES With vehicle on a level surface and en- XPS RECOMMENDED ENGINE OIL gine cold, not running, check the oil Scandinavia: level as follows: 4T 5W40 1. Unscrew dipstick then remove it SYNTHETIC and wipe clean. BLEND OIL (EUR) 2.

  • Page 140: Oil Filter

    II MAINTENANCE PROCEDURES Engine Oil Change Wait a while to allow oil to flow down to crankcase then check oil level. Refill as necessary. CAUTION The engine oil can be very hot. Wait until engine oil is Dispose of oil as per your local environ- warm.

  • Page 141: Radiator

    II MAINTENANCE PROCEDURES 8. Wipe off any oil spillage on engine. 4) Radiator Radiator Inspection Periodically check the radiator area for cleanliness. tmr2011-010-005_a 1. Outlet bore to the engine oil providing system 2. Inlet bore from the oil pump to the oil filter 2.

  • Page 142: Engine Coolant

    II MAINTENANCE PROCEDURES See an authorized Can-Am dealer, re- pair shop or person of your own choos- ing to check the performance of the cooling system. 5) Engine Coolant Engine Coolant Level Verification WARNING Check coolant level with engine vmo2012-012-042_a cold.
  • Page 143 II MAINTENANCE PROCEDURES NOTICE Do not store any objects WARNING under the gauge support. To avoid potential burns, do not remove the pressure cap if the en- Recommended Engine Coolant gine is hot. RECOMMENDED COUNTRY COOLANT EXTENDED LIFE PRE-MIXED Scandinavia COOLANT (EUR) (P/N 779223) EXTENDED LIFE...

  • Page 144: Muffler Spark Arrester

    II MAINTENANCE PROCEDURES All Models 2. Fill the cooling system until coolant comes out of the bleed screw(s). Reinstall cooling system drain plug with a new sealing ring. 650 models Tighten the coolant drain plug to speci- 3. Squeeze the top of the coolant hose fication.
  • Page 145 II MAINTENANCE PROCEDURES CAUTION Let exhaust system cool down before proceeding with cleaning and inspection. Remove the muffler cover. Discard re- taining screws. NOTICE Do not use impact tool for any screw removal. tmo2011-001-041_a TYPICAL 1. Spark arrester 2. Gasket 3.

  • Page 146: Cvt Air Filter

    II MAINTENANCE PROCEDURES Reinstall muffler cover with new re- taining screws. Tighten to specifica- tion. TIGHTENING TORQUE Tail pipe screws 11 N•m ± 1 N•m (97 lbf•in ± 9 lbf•in) Cover screws 219002146-003 TYPICAL 7) CVT Air Filter CVT Air Filter Cleaning 1.

  • Page 147: Gearbox Oil

    II MAINTENANCE PROCEDURES 8) Gearbox Oil Recommended Gearbox Oil RECOMMENDED GEARBOX OIL Gearbox Oil Level Verification 75W140 NOTICE Check level and refill if SYNTHETIC necessary. Do not overfill. Operat- Scandinavia GEAR OIL (EUR) ing the gearbox with an improper (P/N 779215) level may severely damage gear- box.

  • Page 148: Spark Plugs

    II MAINTENANCE PROCEDURES TIGHTENING TORQUE 5 N•m ± 0.6 N•m Oil level plug (44 lbf•in ± 5 lbf•in) Wipe off any spillage. Dispose gearbox oil as per your local environmental regulations. vmo2012-012-056_a 9) Spark Plugs TYPICAL - 650 ENGINE 1. Drain plug 2.

  • Page 149: Cvt Cover

    II MAINTENANCE PROCEDURES WARNING Never touch CVT while engine is running. Never drive vehicle when CVT cover is removed. WARNING Engine must be cool before cover is removed. Always wear protec- tive gloves when removing cover. 219001737-011_a RH SIDE — REAR CYLINDER 1.

  • Page 150: Installing The Cvt Cover

    II MAINTENANCE PROCEDURES CVT COVER Remove Open driven pulley. REQUIRED TOOL PULLER/LOCKING TOOL (P/N 529 036 098) Screw tool in the threaded hole of driven pulley and tighten to open the Vmr2012-018-004_a pulley. 1. CVT cover screw 2. CVT cover 3.

  • Page 151: Drive And Driven Pulleys

    Pulleys frame. Inspecting the Drive and Driven Pulleys This inspection must be performed by an authorized Can-Am dealer, repair shop, or person of your own choosing for maintenance, repair, or replace- ment. ______________...

  • Page 152: Fuses

    II MAINTENANCE PROCEDURES vmo2012-012-031_a A15E0KY 1. Battery holder 2. Retaining screws TYPICAL 1. Fuse 2. Check if melted Battery Cleaning NOTICE Clean battery, battery casing and bat- Do not use a higher rated tery posts using a solution of baking fuse as this can cause severe dam- soda and water.

  • Page 153: Lights

    II MAINTENANCE PROCEDURES NOTE: Check inside fuse box cover to know fuses location. NOTICE Do not store any objects in the front service compartment. Front Fuse Box Description FRONT FUSE BOX vmr2015-044-004_a DESCRIPTION RATING FUSE HOLDER Cooling fan relay Main relay Lights relay Trailer relay Accessories relay...
  • Page 154 II MAINTENANCE PROCEDURES Rotate light bulb counterclockwise to Pull out bulb. release it from light housing. Properly reinstall removed parts in the reverse order of their removal. Validate headlights and front turn sig- nals operation. Headlight Beam Aiming Turn adjustment knobs to adjust beam height to your convenience.
  • Page 155 II MAINTENANCE PROCEDURES 219001870-001_a 219001868_014_a 2. Replace the bulb. TYPICAL - FRONT TURN SIGNAL LIGHT 1. Retaining screws 3. Reinstall the cover. 2. Replace the light bulb. Taillight and Rear Turn Signal Bulb 3. Reinstall the socket. Replacement Unscrew screws securing taillight as- Front Position Light Replacement sembly.

  • Page 156: Drive Shaft Boot And Protector

    Secure vehicle on jack stands. Drive Shaft Boot and Protector Push and pull the wheels from the up- Inspection per edge to feel the play. Visually inspect drive shaft protectors See an authorized Can-Am dealer if and boots conditions. there is any play. ______________...

  • Page 157: Wheels And Tires

    The tires are directional and their rotation must be kept in a specific direction for proper operation. Tire Replacement Tires replacement should be per- formed by an authorized Can-Am dealer. tmo2011-001-131_a TYPICAL WARNING 19) Wheels and Tires –...

  • Page 158: Steering

    II MAINTENANCE PROCEDURES Push and pull the wheels from the front TIGHTENING TORQUE or rear edge to feel the play. 80 N•m ± 5 N•m Wheel lug nut The tie-rod ends must be replaced if (59 lbf•ft ± 4 lbf•ft) there is an abnormal play or a boot is cracked.
  • Page 159 Shock Absorbers Check trailing arms for distortion, cracks or bending. Inspect shock absorber for oil leaks or other damage. See an authorized Can-Am dealer if any problem is detected. Check tightness of fasteners. See an authorized Can-Am dealer as necessary.

  • Page 160: Brakes

    II MAINTENANCE PROCEDURES 22) Brakes Brake Fluid Reservoir Level Verification With vehicle on a level surface, check brake fluid in reservoirs for proper level. NOTE: A low level may indicate leaks or worn brake pads. Front Brake Reservoir Level Verification vmo2012-012-035_a 1.
  • Page 161 Wait for the brakes to cool down. The brake inspection, maintenance and repair should be performed by an authorized Can-Am dealer. However, verify the following between visits to your dealer: – Brake fluid level – Brake system for fluid leaks –...

  • Page 162: Vehicle Care

    III VEHICLE CARE 1) Post-Operation Care Non Compatible Cleaning Products When vehicle is used in salt-water en- NON-COMPATIBLE MATERIAL vironment (beach area, launching and CLEANING TYPE loading boats etc.), rinsing the vehi- PRODUCTS cle with fresh water is necessary to preserve vehicle and its components.
  • Page 163 III VEHICLE CARE Compatible Cleaning Products MATERIAL COMPATIBLE TYPE CLEANING PRODUCT Soapy water Polypropylene XPS ATV WASH (P/N 219 701 702) vbs2012-006-001 SAFE FOR POLYPROPYLENE ______________...

  • Page 164: Storage And Preseason Preparation

    4 months, proper storage is a ne- cessity. When using your vehicle after storage, a preparation is required. See an authorized Can-Am dealer, re- pair shop, or person of your own choos- ing to have your vehicle prepared for either storage or the preseason.

  • Page 165: D) Technical Information

    D) TECHNICAL INFORMATION ______________...

  • Page 166: Ec-Declaration Of Conformity

    EC-DECLARATION OF CONFORMITY DoC_ATV_MY21-T Cat ______________...

  • Page 167: Eac Declaration Of Conformity

    EAC DECLARATION OF CONFORMITY Left blank for Eurasian Conformity mark where applicable ______________...

  • Page 168: I Specifications

    I SPECIFICATIONS 1000 MODEL ENGINE ROTAX ® ROTAX ® 1000 Engine type 4-stroke, Single Over Head Camshaft (SOHC), liquid cooled Number of cylinders Number of valves 4 valves / cylinder (mechanical adjustment) Intake 0.06 mm to 0.14 mm (.0024 in to .0055 in) Valve clearance Exhaust 0.11 mm to 0.19 mm (.0043 in to .0075 in)
  • Page 169 I SPECIFICATIONS 1000 MODEL COOLING SYSTEM EXTENDED LIFE PRE-MIXED Scandinavia: COOLANT (EUR) (P/N 779223) EXTENDED LIFE All other countries: Type PRE-MIXED COOLANT (P/N 779150) Coolant or coolant specifically designed for aluminum engines Capacity 3.4 L (.9 U.S. gal.) CVT TRANSMISSION Type CVT (Continuously Variable Transmission) Engagement RPM...
  • Page 170 I SPECIFICATIONS 1000 MODEL ELECTRICAL SYSTEM (cont'd) High 2 x 60 W Headlights 2 x 55 W Taillights 2 x 5/21 W Turn signal lights 4 x 10 W Position lights 2 x 5 W Licence plate light 2 x 5 W FUSES MAINTENANCE Fuses...
  • Page 171 I SPECIFICATIONS 1000 MODEL DRIVE SYSTEM (cont'd) CV JOINT GREASE (P/N 293 550 CV joint grease 062) or an equivalent PROPELLER SHAFT GREASE (P/N 293 Propeller shaft grease 550 063) or an equivalent FRONT SUSPENSION Suspension type Arched double a-arm with front stabilizer bar Suspension travel 23.3 cm (9.2 in) Shock absorber...
  • Page 172 I SPECIFICATIONS 1000 MODEL TIRES Vehicle load of less 34.5 kPa (5 PSI) than 234 kg (515 lb) Front Vehicle load from 234 kg to 460 kg 48.3 kPa (7 PSI) (515 lb to 1,015 lb) Pressure Vehicle load of less 34.5 kPa (5 PSI) than 234 kg (515 lb) Rear...
  • Page 173 I SPECIFICATIONS 1000 MODEL DIMENSIONS 1-UP 297 cm (116.9 in) Overall length 2-UP 317 cm (124.8 in) Overall width 122 cm (48 in) 1-UP 126 cm (49.6 in) Overall height 2-UP 141 cm (55.5 in) 1-UP 208 cm (81.9 in) Wheelbase 2-UP 228 cm (89.8 in)
  • Page 174 I SPECIFICATIONS This page is intentionally blank ______________...

  • Page 175: E) Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 176: Troubleshooting Guidelines

    • Install new spark plugs if possible or clean and dry spark plugs. • Start engine as explained above. If engine continues to flood, see an authorized Can-Am dealer. NOTE: Make sure to verify that there is no fuel in engine oil, if so, replace engine oil.
  • Page 177 – A failure of the fuel pump may have occurred. – Check fuel pump fuse and relay. – If engine does not start, seek service from an authorized Can-Am dealer, re- pair shop, or person of your own choosing for maintenance, repair, or replace- ment.
  • Page 178 3. Cooling fan inoperative. – Check cooling fan fuse, refer to MAINTENANCE section. If the fuse is good, seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or replacement. ENGINE BACKFIRE 1.
  • Page 179 – Once the load is reduced, the normal steering assistance will return. 2. CHECK ENGINE INDICATOR LAMP is ON and display shows CHECK DPS – Seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or replacement.

  • Page 180: Multifunction Gauge Messages

    If the message and the check engine light stay on after engine starting, stop engine. Check engine oil level. Refill if necessary. If the oil level is good, seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or replacement. Do not use the vehicle until repaired.
  • Page 181 II MULTIFUNCTION GAUGE MESSAGES To erase the MAINTENANCE REQUIRED message, proceed as follows: 1. From main display (vehicle speed), press SET and HOLD. 2. Alternate between LOW beam and HIGH beam 3 times. NOTE: Step 2 must be completed within 2 seconds. 3.
  • Page 182 II MULTIFUNCTION GAUGE MESSAGES This page is intentionally blank ______________...

  • Page 183: F) Spare Parts

    F) SPARE PARTS ______________...

  • Page 184: I Catalogs

    I CATALOGS You will find your Can-Am ATV spare parts on our website at www.epc.brp.com. ______________...

  • Page 185: G) Warranty

    G) WARRANTY ______________...

  • Page 186: Brp Limited Warranty Usa And Canada: 2021 Can-Am Atv

    SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. ("BRP")* warrants its 2021 Can-Am ATV sold by authorized Can-Am ATV dealers (as hereinafter defined) in the United States of America ("USA") and in Canada from defects in material or workmanship for the period and under the conditions described below.
  • Page 187 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2021 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am ATV dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred (“Can-Am ATV dealer”);...
  • Page 188 BRP’s obligations under this warranty are limited to, at its sole discretion, repairing parts found defective under normal use, maintenance and service, or replacing such parts with new genuine Can-Am ATV parts without charge for parts and labor, at any authorized BRP dealer during the warranty coverage period under the conditions described herein.

  • Page 189: Epa Emission-Related Warranty

    BRP. For all emission-related warranty claims, BRP is limiting the diagnosis and repair of emission-related parts to the authorized Can-Am dealers, unless for emergency re- pairs as required by item 2 of the following list.
  • Page 190 Components Covered The emission-related warranty covers all components whose failure would in- crease an engine’s emissions of any regulated pollutant, including the following listed components: 1. For exhaust emissions, emission-related components include any engine parts related to the following systems: –...
  • Page 191 Limited Applicability As a certifying manufacturer, BRP may deny emission-related warranty claims for failures that have been caused by the owner’s or operator’s improper main- tenance or use, by accidents for which the manufacturer has no responsibility, or by acts of God. For example, an emission-related warranty claim need not be honored for failures that have been directly caused by the operator’s abuse of the engine/equipment or the operator’s use of the engine/equipment in a manner for which it was not designed and are not attributable to the manufacturer in any way.

  • Page 192: Brp International Limited Warranty: 2021 Can-Am Atv

    1) SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. ("BRP")* warrants its 2021 Can-Am ATV sold by Can-Am ATV distributors or dealers authorized by BRP to distribute Can-Am ATVs ("Can-Am ATV Distributor/Dealer") outside of the United States of America ("USA"), Canada, member states of the European Economic Area (which is comprised of the states of the European Union plus the United King- dom, Norway, Iceland and Liechtenstein) ("EEA"), Turkey, member states of the...
  • Page 193 Can-Am ATV Distributor/Dealer; – Damage caused by abuse, abnormal use, neglect, racing or operation of the product in a manner inconsistent with the recommended operation described in the Operator’s Guide;...
  • Page 194 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2021 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am ATV Distributor/Dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred;...
  • Page 195 9) CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the Can-Am ATV Distribu- tor/Dealer level. We recommend discussing the issue with the authorized Can-Am ATV Distributor/Dealer's service manager or owner.

  • Page 196: Brp Limited Warranty For The European Economic Area, The Commonwealth Of The Independent States And Turkey: 2021 Can-Am Atv

    1) SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. ("BRP")* warrants its 2021 Can-Am ATVs sold by distributors or dealers authorized by BRP to distribute Can-Am ATVs ("Can-Am ATV Distributor/Dealer") in member states of the European Economic Area (which is comprised of the member states of the European Union plus the United Kingdom, Norway, Iceland and Liechtenstein) ("EEA"), in member...
  • Page 197 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2021 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am ATV Distributor/Dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred;...
  • Page 198 BRP's responsibility is limited to making the required repairs or replace- ments of parts. No claim of breach of warranty shall be cause for cancellation or rescission of the sale of the Can-Am ATV to the owner. You may have other legal rights which may vary from country to country.
  • Page 199 9) CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the Can-Am ATV Distribu- tor/Dealer level. We recommend discussing the issue with the authorized Can-Am ATV Distributor/Dealer's service manager or owner.
  • Page 200 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be re- sponsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.

  • Page 201: Maintenance Records

    MAINTENANCE RECORDS Send photocopy of maintenance record to BRP if needed. PREDELIVERY Serial number: Signature/Print: Mileage / km: Hours: Date: Dealer no: Notes: Refer to vehicle Pre-Delivery Bulletin for detailed installation procedures FIRST INSPECTION Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide...
  • Page 202 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 203 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide ______________...
  • Page 204 This page is intentionally blank ______________...

  • Page 205: Customer Information

    CUSTOMER INFORMATION ______________...

  • Page 206: Privacy Information

    PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.

  • Page 207: Contact Us

    CONTACT US North America www.brp.com 565 de la Montagne Street Asia Valcourt (Québec) J0E 2L0 Canada Room 4609, Tower 2, Grand Gateway 3 Hong Qiao Sa De Cv, Av. Ferrocarril 202 Road Shanghai, Parque Ind. Querétaro, Lote2-B China 200020 76220 Santa Rosa Jáuregui, Qro., Mexico 21F Shinagawa East One Tower 2-16-1 Konan, Minatoku-ku,...

  • Page 208: Change Of Address/Ownership

    STOLEN UNITS: If your personal ATV is stolen, you should notify BRP or an autho- rized Can-Am dealer. We will ask you to provide your name, address, phone num- ber, the vehicle identification number and the date it was stolen.
  • Page 209 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 210 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 211 ATV MODEL No. VEHICLE IDENTIFICATION NUMBER (V.I.N.) ENGINE IDENTIFICATION NUMBER (E.I.N.) Owner: NAME STREET CITY STATE/PROVINCE ZIP/POSTAL CODE Purchase Date YEAR MONTH Warranty Expiry Date YEAR MONTH To be completed by the dealer at the time of the sale. DEALER IMPRINT AREA V00A2IL Please verify with your dealer to ensure your vehicle has been registered with BRP.
  • Page 212 WARNING THIS VEHICLE CAN BE HAZARDOUS TO ATE THIS VEHICLE ON A PAVED SURFACE. OPERATE. A collision or rollover can occur quickly, even You increase your risk of losing control if you operate this vehicle on pavement. during routine maneuvers such as turning and driving on hills or over obstacles, if you fail to ATE THIS VEHICLE ON PUBLIC take proper precautions.

Table of Contents