Page 1
2019 CAN-AM SPYDER ON-ROAD VEHICLE OPERATOR’S GUIDE Includes Safety, Vehicle and Maintenance Information SPYDER ® Learn how the Spyder is different. Read this operator‘s guide and watch the safety video on: https://can-am.brp.com/spyder/owners/safety/safety-information.html Complete a training course (if available), pratice and become proficient with the controls.
Page 2
Spyder Rotax ® RT™ BRP Connect™ Can-Am ® XPS™ iPhone, iPod, iPod nano and iPod touch are trademarks of Apple Inc. registered in U.S.A. and other countries. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
Denna bok kan finnas tillgänglig på ditt språk. Kontakta din återförsäljare Svenska eller gå till: www.operatorsguides.brp.com Congratulations on your purchase of a Your dealer is committed to your sat- new Can-Am ® Spyder ® . It is backed by isfaction. He has taken training to pre-...
FOREWORD About this Operator's At delivery, you were informed about the warranty coverage and also, you Guide PREDELIVERY CHECK signed the This Operator's Guide was written in LIST to ensure your new vehicle was North America in a right-lane driving prepared to your entire satisfaction.
In addition to reading this Operator's Guide, you should read the Safety Card on the vehicle, all on-product safety labels and watch the video located at: https://can-am.brp.com/spyder/own- ers/safety/safety-information.html If possible, take a training course that is specifically designed for a 3-wheel ve- hicle.
Page 10
TABLE OF CONTENTS WARRANTY BRP LIMITED WARRANTY — USA AND CANADA: 2019 Can-Am ® SPYDER ® SERIES ................160 BRP LIMITED WARRANTY OUTSIDE USA AND CANADA: 2019 Can-Am ®...
GENERAL PRECAUTIONS Avoid Carbon Monoxide – Never top off the fuel tank. Leave some room for the fuel to expand Poisoning with temperature changes. All engine exhaust contains carbon – Wipe up any spilled fuel. monoxide, a deadly gas. Breathing car- –...
Page 12
GENERAL PRECAUTIONS is modified, such as changing weight distribution, wheelbase, tires, suspen- sion, brakes or steering. See your authorized Can-Am On-Road dealer for available accessories for your vehicle. ______________...
PRIMARY CONTROLS It is important to know the location and operation of all controls, and to develop and practice smooth and coordinated use of them. 219002010-001 TYPICAL Handlebar Throttle Gearshift Selector Brake Pedal Parking Brake Button 1) Handlebar Grip the handlebar with both hands. Steer the handlebar in the direction you want to go.
PRIMARY CONTROLS To decrease engine speed, roll the throttle as shown (raise your wrist). 219001827-004_a TYPICAL 1. Gearshift selector The gear pattern is Reverse-Neu- tral-1-2-3-4-5-6. rmo2010-001-031_j TO DECREASE SPEED Press selector forward to upshift. Pull selector toward you to downshift. The throttle is spring loaded and should return to idle when you release your grip.
If this condition persists or if you find erwise, the engine management will any braking system problems, refer to activate the limp home mode to pro- an authorized Can-Am On-Road dealer. tect the braking system. 5) Parking Brake Button The parking brake button is located on the LH grip.
Page 17
PRIMARY CONTROLS Releasing Parking Brake To release parking brake, press button and make sure brake indicator lamp turns OFF. 219001827-006_i 1. Parking brake button NOTE: To apply or release the parking brake, the ignition key must be turned NOTE: The battery voltage must be 219001827-006_i 1.
DIAGNOSTIC GUIDELINES fer to the Store the spare key in a safe place be- cause you must have your spare key to have another one made by an autho- rized Can-Am On-Road dealer. Ignition Function rmo2008-001-002_a IGNITION SWITCH 1. OFF 2.
SECONDARY CONTROLS 3) Engine Stop Switch The engine stop switch is near the right handgrip. rmo2010-001-031_d 1. Cruise control switch The switch is a multifunction switch. It allows to activate, set and stop the function of the cruise control. rmo2010-001-031_b 1.
Page 21
SECONDARY CONTROLS WARNING WARNING Improper use of the cruise control Always keep both hands on the can lead the vehicle to a loss of handlebar while riding. Other- control. wise, this could cause a vehicle loss of control. Setting the Cruise Control NOTE: You can increase engine speed To use the cruise control, the vehicle using the throttle grip if you need to go...
SECONDARY CONTROLS Stopping the Cruise Control To completely stop the cruise control operation, slide the cruise control but- ton to the left. rmo2010-001-031_f CRUISE CONTROL PREVIOUSLY SET 1. Push down button to reduce the speed setting Cancelling the Cruise Control Any of the following event will cancel rmo2010-001-031_h the cruise control.
SECONDARY CONTROLS To select high beams, push the switch The turn signal button turns off auto- to the front position. To select low matically after a normal turn, but you beams, push the switch to the back may have to turn it off manually after a position.
SECONDARY CONTROLS 9) Windshield Adjustment Button The windshield adjustment button is located near the left handgrip. 219001827-006_f TYPICAL 1. To raise windshield 2. To lower windshield 10) Reverse Button The reverse button is located on top of 219001827-006_e the left handlebar housing. TYPICAL 1.
SECONDARY CONTROLS Audio Control To turn the radio ON, push the JOY- STICK UP. To close the radio, push the JOYSTICK DOWN when the volume is at its lowest setting. When in the home screen, pushing the JOYSTICK UP or DOWN will increase or decrease the audio volume.
SECONDARY CONTROLS 13) Switch Cluster The switch cluster is located above the glove box. It gives control of numerous electrical accessories. NOTE: The switch cluster is opera- tional only when the engine is running and the battery voltage is over 11 Vdc. 219001827-009_c 1.
Page 27
SECONDARY CONTROLS Press the switch to the opposite icon side to turn off the fog lights. 219001827-009_f 1. Press here to turn off _______________...
PASSENGER CONTROLS rmo2011-001-002_a 1. HI intensity button (both lights will be on) 2. HI intensity indicator To select the OFF position, press the OFF button. rmo2010-001-029_b NOTE: The heated grips will shut off 1. Passenger Heated Grip Switch 2. Passenger Audio Control (option) when engine is under 800 RPM and will not resume automatically.
Page 29
PASSENGER CONTROLS WARNING Reading or tempering with the multifunction gauge can distract you from the operation of the vehi- cle, particularly from constantly scanning the environment. Al- ways pay attention to road con- ditions, ensure your environment is clear and free from obstacles. Furthermore, when riding, only glance at the multifunction gauge briefly to maintain awareness of...
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Basic Functions To select the value to be displayed in the tripmeter; LCD Display 1. Access the Stats/Trip screen 2. Select the desired set of statistic to Default Display be shown (Total, A or B) 3.
Page 31
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Navigating in the Digital Display – Audio – Settings WARNING When an icon is selected, its related screen will appear. Reading or tampering with the multifunction gauge can distract you from the operation of the vehi- cle, particularly from constantly scanning the environment.
Apple App Store or Google Play Store Use the ECC to control of numerous via a simple search. Not all phones are functions of the multifunction gauge. compatible. NOTE: Refer to the Can-Am On-Road site (www.brpconnecttuto- rial.com) for further details. ______________...
Page 33
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY NOTE: The smartphone must be con- The Statistics menu is used to get : nected via Bluetooth and with a USB – Trip distance information cable to the USB port located in the – Trip elapsed time information front storage compartment.
Page 34
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Use the joystick to control the audio NOTE: A different volume level is volume. Joystick UP for louder. used when helmet is selected. This allows to keep the volume previously To mute the audio, push the joystick selected when music was sent to the DOWN and hold it for more than one helmet.
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Pairing your Smartphone NOTE: You must have an Apple™ iTunes™ or Google™ Play Store ac- Via Bluetooth count to download the application. On the vehicle 2) Download Apps Compatible With 1. Short press the JOYSTICK to ac- BRP Connect cess menu.
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY Quick Tour of the BRP – 3) Settings: Set BRP connect to your choosing. In which country do Connect App you intend to use the BRP Connect App? What should be worth your at- tention? Note: Elementary settings of the BRP Connect app change be changed from within this menu.
Page 37
LARGE PANORAMIC 7.8" WIDE LCD DISPLAY 219002011-501 – 1) Currently Installed Apps – 2) Available Apps _______________...
EQUIPMENT Mirrors Opening the Glove Box First ensure steering is not locked to al- Adjusting Mirrors low glove box opening. Press the mirror at the points shown Push on the lower end of glove box to below to adjust its position in the four release it.
EQUIPMENT Front Storage Seat Compartment The operator seat is equipped with a provision to install the operator seat Opening the Front Storage backrest (available in option). Compartment 1. Insert key in ignition switch. 2. Push and turn the key 1/4 turn coun- terclockwise to the front storage compartment position and hold while lifting cover.
EQUIPMENT rmo2010-001-048_a rmo2010-001-046_a 1. Turn counterclockwise to unlock 1. Maximum opening of seat Pull the left side latch to open the left Storage Compartments side storage compartment cover and pull the right side latch to open the right side cover. Opening the Side Storage Compartments The side storage compartment latches...
Page 41
EQUIPMENT rmo2010-001-048_b rmo2010-001-048_a 1. Turn clockwise to lock 1. Turn counterclockwise to unlock NOTICE Never ride the vehicle Pull the latch. with any cover open. Closing the Side Storage Compartments Lift slowly the side storage compart- ment cover to let air flow out. Bring the cover at closing position.
EQUIPMENT Closing the Top Storage Compartment Bring the cover at closing position. Put your hand in the center of the cover then push to lock. Helmet Securing a Helmet rmo2015-001-104_a Two helmet hooks are provided under TYPICAL the seat to secure a helmet. 1.
EQUIPMENT Body Panels The body panels on the vehicle can be removed for maintenance. rmo2014-005-033_a LEFT HAND SIDE PANELS 1. Side panel 2. Top side panel 3. Rear side panel 4. Bottom front side panel 5. Bottom rear side panel Side Panel 1.
Page 44
EQUIPMENT Installation rmr2010-038-004_b Step 1: Push towards the rear Step 2: Push up rmo2010-008-003_n 6. Remove upper retaining screws INSTALLATION SEQUENCE from top side panel. Reinstall side panel in the reverse order of the removal. Top Side Panel Removal 1. Open seat. 2.
Page 45
EQUIPMENT Installation Reinstall top side panel in the reverse order of the removal. Rear Side Panel Removal 1. Remove side panel. 2. Remove top side panel. rmr2010-038-007_b 3. Remove front retaining screw of 1. Left service cover rear side panel. 2.
Page 46
EQUIPMENT rmr2010-038-012_a 1. Rear retaining screws rmr2010-038-015_a 8. Remove top retaining screw of rear 1. Upper retaining screw side panel. 2. Upper plastic rivet 4. Remove the 2 bottom plastic rivets from the panel. rmr2010-038-013_a 1. Top retaining screw rmr2010-038-016_a 9.
Page 47
EQUIPMENT rmr2010-038-017_a rmo2014-005-032_a 1. Front retaining nut 1. Bottom retaining screw 6. Remove retaining screws from bot- 2. Upper retaining screw tom rear RH side panel. 6. Loosen upper retaining screw. NOTE: Upper retaining screw remains attached to bottom panel. 7.
BASIC PROCEDURES Adjusting the Passenger Starting and Stopping the Footrest Engine For the passenger's comfort, Starting the Engine footrest height can be adjusted. Flip the footrest upward. WARNING Turn the retaining screw counterclock- Exhaust gas contains poisonous wise with a wrench (stored in the tool carbon monoxide that can rapidly kit) to loosen the screw.
BASIC PROCEDURES 7. Release the parking brake. Make 3. Dismount on the right side of the ve- sure the brake indicator lamp on the hicle, keeping your foot on the brake multifunction gauge is off. pedal. 4. Push the vehicle, using the brake as Stopping the Engine needed.
BASIC PROCEDURES During the first 300 km (200 mi), avoid Alcohol fuel blending varies by coun- hard braking. try and region. Your vehicle has been designed to operate using the recom- mended fuels, however, be aware of WARNING the following: New brakes and tires do not op- –...
BASIC PROCEDURES Refueling Procedure NOTE: Do not try to top off the fuel tank. Leave some room for the fuel to expand with temperature changes. WARNING 6. Wipe up any spilled fuel. If fuel spills Gasoline is extremely flammable on you, wash with soap and water and highly explosive.
BASIC PROCEDURES NOTE: When adjusting the pressure, do not put your weight on the vehicle and do not load cargo in the storage compartment. The air spring is connected directly to an air hose with a schrader valve lo- cated under the seat. 219001827-013_a 1.
WHAT'S DIFFERENT FROM OTHER VEHICLES This section will help you understand The braking and steer are similar to a some of the vehicle distinctive fea- motorcycle. Be aware of vehicle be- tures and operating characteristics. hind you, they may not able to stop or react as quickly.
WHAT'S DIFFERENT FROM OTHER VEHICLES Driver's License and Local In tight turns, it may help to lean your upper body forward and toward the in- Laws side of the turn. Driver's license requirements for oper- ating this vehicle vary by location. De- Width pending on local laws, you may need Because this vehicle is wider than a...
DRIVING AID TECHNOLOGIES Vehicle Stability System Surfaces with Poor Traction (VSS) The grip of tires on the road surface limits the maximum braking. Even This vehicle is equipped with a Vehicle with ABS and EBD, your stopping dis- Stability System (VSS). tance will be longer on surfaces with This system helps to keeping the con- poor traction' if you do not maintain the...
DRIVING AID TECHNOLOGIES Use only BRP recommended tires, which can be ordered only from an au- thorized Can-Am On-Road dealer. Proper tire inflation pressure and tread condition are important for maintaining traction, especially on loose or wet sur- faces. Hard Turns The VSS does not control or limit steer- ing input —...
Read this Opera- like the behavior of other drivers, are tor's Guide, watch the video located at: beyond your control. https://can-am.brp.com/spyder/own- Here are some of the factors that affect ers/safety/safety-information.html, your risk: and if available, take a training course.
UNDERSTANDING RISK ON THE ROAD good physical and mental condition is even more important than for a car. The safest policy is to never operate the vehicle unless you are alert and completely sober. Even if your blood alcohol level is not over the legal limit, your judgment and skills are impaired by any alcohol consumption.
RIDING GEAR Riding this three-wheeled, open-air ve- with the back of the operator's helmet. hicle requires the same protective gear Even the best helmet is no guarantee as motorcycling. Even though the ve- against injury, but statistics indicate hicle is more stable at low speeds than that helmet use significantly reduces a motorcycle, you can still be thrown the risk of brain injury.
Page 61
RIDING GEAR Gloves Leather is a good choice because it is durable and wind-resistant and pro- Full-fingered gloves protect hands vides protection against injury. Other from the wind, sun, heat, cold and abrasive-resistant protective gear flying objects. Gloves that fit snugly made of synthetic fabrics are good will improve grip on the handlebar and choices, too.
Page 62
RIDING GEAR idea to carry rain gear. A dry rider will be much more comfortable and alert than a rider who is wet and cold. One or two-piece styles are available, and those designed specifically for mo- torcycling are best. High-visibility or- ange or yellow colors are good choices.
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Before you take this vehicle on the they do not interfere with the required road, you need to develop riding skills open paths shown in the diagram be- and strategies for managing risk on the low.
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Practice Exercises Even in a closed lot, be aware of poten- tial traffic. Check to the front, sides and rear before doing an exercise. 1) Revving the Engine and Using the Also, watch out for children and ani- Engine Stop Switch mals.
Page 65
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Directions – As you approach the stopping point, release the throttle and press the If you feel like you are losing control brake to stop. while doing these exercises, release – Turn around at the end of the the throttle to stop accelerating and straightaway as before, except now apply the brake as needed to slow...
Page 66
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES – Look in the direction of the curve. – Turn the handlebar in the direction of the curve, pulling on the inside hand- grip and pushing on the outside, be- ing careful not to apply throttle. –...
Page 67
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES 5) Quick Stops Purpose – Become familiar with the vehicle braking ability. – Learn to apply brakes with maxi- mum force. Directions This exercise is similar to what you did before, except you’ll be applying the brake more firmly, working up to braking as hard as possible.
Page 68
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES rmo2008-001-046_f 1. Start rmo2008-005-050_a 2. Stop 1. Start Tips for Additional Practice 12 m (40 ft) Weave – Practice checking your mirrors be- Once you’re comfortable, try doing fore braking hard. 12 m (40 ft) weaves between every other cone/every fourth parking space.
Page 69
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Directions This exercise is similar to what you did before, except now you will be upshift- ing on the straightaways, then coming to a stop at the end of each straight- away. You may want to use the parking lot aisles for this exercise rather than riding in the spaces.
Page 70
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES NOTE: Applying slightly more throt- tle while downshifting can help the engine rev up to match vehicle speed more quickly and make the downshift smoother. When you do not apply throttle while downshifting, engine braking will slow the vehicle.
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Directions BASIC PRO- – Shift into reverse. See CEDURES – Check that the area behind you is clear. Continue to look backwards. Be careful not to strike anything with your front wheels as you back up.
Page 72
REQUIRED RIDING SKILLS AND PRACTICE EXERCISES Start by riding in less challenging situa- tions: – Short distances – Good weather – Low traffic – Daytime – Lower speeds – No passenger. You can gradually move on to more challenging riding situations as you de- velop your skills.
STREET STRATEGIES This section provides some strategies road surfaces, down hills, or when car- to reduce your risk on the road. Many rying more weight, and visibility may of these strategies are similar to those be limited in fog, in curves or at night. used for motorcycles.
STREET STRATEGIES When braking, be particularly aware of turns. Make sure turn signals are off vehicles behind you that may not be after you have completed your ma- able to stop as quickly as you. neuver; leaving them on may confuse other motorists.
STREET STRATEGIES Time of Day and Weather ahead to see you, you must be able to see their mirrors. When you are be- In dim light, such as at night, at dawn ing followed by a large vehicle, passing or dusk, or in poor weather such as rain vehicles may not be able to see you or fog, you may be harder to see.
STREET STRATEGIES Common Riding Situations Turns Remember to slow, look, and steer Intersections through turns. Intersections, including small inter- – Slow: Reduce speed as needed be- sections with alleys and driveways, fore entering a turn by rolling off the present an additional risk due to the throttle, using the brakes, and/or cross traffic.
STREET STRATEGIES Curves night. Use high beams when appro- priate. Avoid overriding your headlight Because this vehicle is narrower than a (riding so fast that you can’t see as far car, you can move from side to side as your stopping distance). You can in the lane in curves to straighten also use other vehicle headlights to your path of travel.
Page 78
STREET STRATEGIES TIRE PRESSURE MAINTE- slippery surfaces. This vehicle is more Refer to NANCE PROCEDURES likely than a car to spin out of control in section. slippery surfaces. NOTE: The pressure difference be- tween the left and right side tire should Gravel, Dirt and Sand not exceed 3.4 kPa (.5 PSI).
TRANSPORTING THE VEHICLE ers, make you lose control, spin or roll ) to over. the nearest Can-Am On-Road dealer to have it thoroughly inspected for If you can’t come to a complete stop safety before riding again. in time to avoid an obstacle, you can –...
STREET STRATEGIES Tire Failure If a tire failure or a blowout suddenly occurs, firmly grip the handlebar, grad- ually slow down and carefully steer to a safe place to stop. Avoid hard braking, downshifting, or sharp steering. If a front tire fails, the vehicle may tend to pull in the direction of the failed tire, so you will need to maintain a firm grip on the handlebar to control your direction.
CARRYING A PASSENGER, CARGO OR TOWING A TRAILER Weight Limits – Reduce ground clearance, increas- ing the risk of striking low obstacles Do not exceed the weight limits for rid- or uneven road surfaces. ers and cargo. – Increase the risk of tire failure. Operating with Extra Weight Carrying a passenger or heavy cargo...
CARRYING A PASSENGER, CARGO OR TOWING A TRAILER The passenger should use its audio control in respect to the rider's direc- tives. Be sure the passenger is wearing ap- propriate protective gear. The passen- ger should wear all of the protective gear recommended for the operator, particularly a helmet.
CARRYING A PASSENGER, CARGO OR TOWING A TRAILER Glove Box The glove box provides room to store small personal articles. It is very convenient to store items that could be needed quickly during a ride (such as money for pay toll). Front Storage Compartment The front storage compartment is the most spacious and has room to store...
Page 84
NOTE: For information about the ma- ERCISES ximum cargo that can be loaded in When possible, avoid swerving, twist CAN-AM FREEDOM trailer, refer to the and turns, sharp and abrupt turns as TRAILER OPERATOR'S GUIDE well as sudden braking. This could...
Page 85
CARRYING A PASSENGER, CARGO OR TOWING A TRAILER NOTICE Exceeding the maximum towed weight can damage vehicle or trailer. Avoid transporting heavy parts with sharp edges that could damage the trailer. Place the cargo so that it does not shift while the rmo2010-001-501_a trailer is being towed.
Front brake lever You should only replace the tires with those approved by BRP You should leave your low beam obtained from an authorized lights on during the day for added Can-Am On-Road dealer. visibility. True False True False It is important for the passenger to 10.
Page 87
KNOWLEDGE SELF-TEST 18. A passenger should hold onto the 12. Under normal conditions, operator. following distance should be at least ________. True False a. 1 second 19. Riding this vehicle is as safe as b. 2 seconds riding in a car. c.
KNOWLEDGE SELF-TEST Answers 13. True False 14. 1) Make sure your lights and To stop quickly, press the brake reflectors are clean. pedal only. 2) Use your high beams whenever possible. False 3) Use your turn signals. You should do a pre-ride inspection 4) Flash your brake lights before every time you ride.
Il nécessite des habiletés et des connaissances spéciales. Il nécessite des habiletés et des connaissances spéciales. This Can-Am On-Road is a different type of vehicle - This Can-Am On-Road is a different type of vehicle - Sachez ce qui distingue ce produit Can-Am des autres véhicules.
Learn how this product is different. Read the operator’s guide and watch the safety video using the QR code link or visit Can-Am On-Road web site. Complete a training course (if available), practice, become proficient with the controls, and get a proper license.
The following labels are on your vehicle, and they should be considered permanent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized Can-Am On-Road dealer. NOTE: In the event of any discrepancy between this guide and the vehicle, the safety labels on the vehicle have precedence over the labels in this guide.
Page 92
SAFETY INFORMATION ON THE VEHICLE Label 2 Label 3 NOTICE DO NOT OVERLOAD -Matt finish paint needs 16 kg (35 lb) special care to maintain its appearance. LOAD LIMIT See operator’s guide 5121A -PVD chrome wheel should 704905121 be washed with water and a mild soap.
Page 93
Make sure engine is at operating temperature. For procedure refer to the operator’s guide. - Ride at least 15 km (9 miles). - Can-Am Spyder must be on a level surface. - Let engine idle for 10 minutes. rmo2010-001-100_a - Stop engine.
Page 94
SAFETY INFORMATION ON THE VEHICLE rmo2010-001-102_a 1. Label 7 located underneath service cover rmo2016-006-007_c Label 8 TYPICAL 1. Label 9 located underneath seat Label 10 WARNING Clean filler cap before removing. Use only DOT 4 brake fluid from a sealed container. 704903119 704903119 704904116A...
The following labels are on your vehicle, and they should be considered permanent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized Can-Am On-Road dealer. NOTE: In the event of any discrepancy between this guide and the vehicle, the safety labels on the vehicle have precedence over the labels in this guide.
Page 96
SAFETY INFORMATION ON THE VEHICLE Label 2 Label 3 NOTICE DO NOT OVERLOAD -Matt finish paint needs 16 kg (35 lb) special care to maintain its appearance. LOAD LIMIT See operator’s guide 5121A -PVD chrome wheel should 704905121 be washed with water and a mild soap.
Page 97
Make sure engine is at operating temperature. For procedure refer to the operator’s guide. - Ride at least 15 km (9 miles). - Can-Am Spyder must be on a level surface. - Let engine idle for 10 minutes. rmo2010-001-100_a - Stop engine.
Page 98
SAFETY INFORMATION ON THE VEHICLE rmo2010-001-102_a 1. Label 7 located underneath service cover rmo2016-006-007_c Label 8 TYPICAL 1. Label 9 located underneath seat WARNING Clean filler cap before removing. Use only DOT 4 brake fluid from a sealed container. 704903119 704903119 rmo2010-001-013_d TYPICAL...
REPORTING SAFETY DEFECTS Your safety is very important to Bombardier Recreational Products Inc. (BRP). If you have any concerns you should immediately contact BRP cus- tomer service. In the USA, if you believe that your ve- hicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the Na- tional Highway Traffic Safety Adminis-...
Page 100
REPORTING SAFETY DEFECTS This page is intentionally blank _____ ______ SAFE OPERATING INSTRUCTIONS...
See an authorized cluded in any warranty campaign. We Can-Am On-Road dealer as neces- also urge you to visit your authorized sary. BRP On-Road dealer in a timely man- ner if you become aware of any safety related campaigns.
PRE-RIDE CHECKLIST ITEM PROCEDURE GEARSHIFT Be sure gearshift selector operates normally in both directions SELECTOR and returns to center when released. PASSENGER FOOTREST Be sure the passenger is comfortable with the footrest height. HEIGHT Adjust as necessary. ADJUSTMENT Ensure that total load on the vehicle (including operator, passenger, cargo and added accessories) does not exceed WEIGHT TECHNICAL SPECIFICATIONS...
Page 104
PRE-RIDE CHECKLIST This page is intentionally blank ______________...
Although an authorized Can-Am On-Road dealer has an in-depth technical knowl- edge and tools to service your vehicle, the emission-related warranty is not condi- tioned on the use of an authorized Can-Am On-Road dealer or any other establish- ment with which BRP has a commercial relationship.
Page 107
Check engine coolant level. Check operation of control switches and passenger switches. Check the drive belt condition and its tension. (Performed by an authorized Can-Am On-Road dealer) Check tightening torque of the rear wheel axle nut. (Performed by an authorized Can-Am On-Road dealer) Visually check brake pads and discs condition.
Page 108
Check tie-rods condition. Check shock absorbers for leaks or other damages. Check tightening torque of the rear wheel axle nut. (Performed by an authorized Can-Am On-Road dealer) Check ball joints condition. Check front and rear wheel bearings condition. Check brake pads and discs condition.
We recommend that after the first 5 000 km (3,000 mi) of operation, your vehicle be inspected by an authorized Can-Am On-Road dealer, repair shop, or person of your own choosing. This maintenance is very important and must not be neglected.
4T 5W40 SYNTHETIC BLEND OIL skills are required. (EUR) (P/N 779290) Several procedures must be done by If THE RECOMMENDED XPS an authorized Can-Am On-road dealer, ENGINE OIL IS NOT AVAILABLE repair shop, or person of your own choosing. Use a 5W40 4-stroke SAE...
Page 111
MAINTENANCE PROCEDURES NOTICE Adjusting the oil level on 9. Unscrew and remove the dipstick a cold engine will result in overfill- again. ing. 10. Check the engine oil level on the dipstick. It should be near or equal 1. Take a ride of at least 15 km (9 mi). to the upper mark.
Page 112
MAINTENANCE PROCEDURES NOTICE Adjusting the oil level on a cold engine will result in overfill- ing. 3. Stop the engine. NOTE: Engine oil level verification must be performed within 2 minutes after engine stop. 4. Recheck oil level. 5. Repeat the above steps until oil rmr2014-011-301_b level reaches the dipstick between TYPICAL...
Page 113
MAINTENANCE PROCEDURES OIL QUANTITIES WHEN MODEL QUANTITY DOING... Engine oil and engine 5.2 L oil filter (5.5 qt (U.S. liq.)) replacement Engine oil, rmr2014-011-081_a engine 1. Oil filter cover oil filter 2. O-rings 5.4 L and HCM 3. Oil filter (5.7 qt (U.S.
MAINTENANCE PROCEDURES Air Filter Inspecting the Air Filter Inspect air filter for cleanliness and Removing the Air Filter damage. 1. Remove the following body pan- NOTICE It is not recommended to els to access the air filter. Refer to blow compressed air on the paper BODY PANELS EQUIPMENT filter.
MAINTENANCE PROCEDURES Engine Coolant With the engine cold, check the coolant level as follows: Recommended Engine Coolant 1. Park the vehicle on a firm, level sur- face. NOTICE Always use ethylene-gly- col antifreeze containing corrosion 2. Open the front storage compart- inhibitors specifically for internal ment cover.
2. HOT coolant level reference line 10. Reinstall the service cover. NOTE: A coolant system that fre- quently requires coolant indicates leaks or engine problems. See an au- thorized Can-Am On-Road dealer. Radiator Fans Cleaning the Radiator Fans Remove any debris from the grills. rmo2010-001-044...
Page 117
When the battery is charged: Always have the battery replaced by an 6. First disconnect the BLACK (-) cable. authorized Can-Am On-Road dealer. 7. Disconnect the RED (+) cable. WARNING NOTICE Always disconnect the...
Drive Belt Alignment Inspect for the following conditions: . If belt goes beyond the outside edge of sprocket, have the belt properly REQUIRED aligned by an authorized Can-Am On WEAR CONDITION ACTION -Road dealer as soon as possible. Good condition NOTE: Belt must NOT be in contact with flange from FRONT SPROCKET.
Replace if damaged or broken. adjusted as soon as possible by an au- – Replace and lubricate the bearing thorized Can-Am On-Road dealer. Pay seal of the rear axle. particular attention during break-in pe- – Replace and lubricate rear axle riod (first 1 000 km (600 mi)).
Page 120
If any of the above occurs, have the tire repaired or replaced as soon as possi- WARNING ble by an authorized Can-Am On-Road dealer. The tires are designed to rotate only in one direction. Do not Tire Tread Wear switch the left and right front wheels.
The 4. Add fluid as required. Refer to “Tire Registration Form” is available at ADDING BRAKE FLUID an authorized Can-Am On-Road dealer. NOTE: Low brake fluid may indicate Brakes leaks or worn brake pads. See an au- thorized Can-Am On-Road dealer.
3. Flip back the floorboard until it latches. The mechanism must 90° work freely. See an authorized Can-Am On-Road dealer if there are any problems with the brake system. Headlights rmo2010-001-008_a Trace 2 lines parallel to the ground on...
Page 123
MAINTENANCE PROCEDURES rbl2015-005-005_a TYPICAL HEADLIGHT REFLECTION ON TEST SURFACE (BOTH HEADLIGHTS) rmo2010-001-007_b 1. Ground A. 10 m (33 ft) 2. Top line A. 703 mm (27-11/16 in) B. 773 mm (30-7/16 in) 90° Verifying the Headlights Aiming (European, Australian and Japanese Models) Low Beam NOTE: This verification is valid for ei-...
Page 124
MAINTENANCE PROCEDURES rmo2015-003-131_a TYPICAL HEADLIGHT REFLECTION ON SURFACE TEST (SINGLE HEADLIGHT) 1. Top line rbl2015-005-003_a 1. HB adjustment knob High Beam NOTE: As the low beam and high European and Australian Models beam are separate units, this verifi- 2. To adjust headlight beam, turn the cation is valid for either left-hand or appropriate adjustment knob.
Page 125
MAINTENANCE PROCEDURES rbl2015-005-002_a rbl2015-005-002_a LH SIDE SHOWN LH SIDE SHOWN 1. High Beam Horizontal Adjustment Knob 1. High Beam Horizontal Adjustment Knob "HB " "HB " 2. High Beam Vertical Adjustment Knob "HB " 2. High Beam Vertical Adjustment Knob "HB "...
VEHICLE CARE Cleaning the Vehicle Vehicles with Matte Finishes Do not use high-pressure washers NOTICE Do not use wax, detail (like the ones found in car washes) as spray, or other products used on they may damage certain parts of the regular paint.
BRP recommends you have your au- 10. Store the vehicle in a dry area, away thorized Can-Am On-Road dealer, re- from sunlight, with a small amount pair shop, or person of your own choos- of daily temperature variation.
Page 128
STORAGE AND PRESEASON PREPARATION This page is intentionally blank ______________...
– Turn the ignition to the ON posi- are present. If the problem is tion. still present without these condi- tions, see an authorized Can-Am On-Road dealer. ENGINE TURNS OVER, BUT DOES NOT START 1. Low fuel.
Page 131
3. Engine management problem. – Check to see whether the engine malfunction indicator lamp is ON while starting. Seek service from an authorized Can-Am On-Road dealer, repair shop, or person of your own choosing for mainte- nance, repair, or replacement.
BAD KEY Defective key On-Road dealer. Use the right key for the vehicle WRONG KEY Wrong key or contact an authorized Can-Am On-Road dealer. Contact an authorized Can-Am CHECK KEY Defective key On-Road dealer. – Stop and wait for engine to cool off.
Page 133
* BRP recommends having the vehicle transported when in LIMP HOME. If you operate the vehicle in LIMP HOME, avoid abrupt maneuvers and immediately go to the nearest authorized Can-Am On-Road dealer to have your vehicle serviced before riding again. In LIMP HOME, the engine RPM is limited and therefore the vehicle speed.
WHAT TO DO IN THE FOLLOWING CIRCUMSTANCES Lost Keys Use your spare key to have another one made by an authorized Can-Am On-Road dealer as soon as possible. If both keys are lost, the ignition switch, the key barrel of the rear storage com-...
Can-Am On-Road dealer. 11. Connect the other end of the After recharging battery, have the vehi- BLACK (-) jumper cable to the cle inspected by an authorized Can-Am NEGATIVE (-) terminal seat of your On-Road dealer. vehicle. ______________...
If an electrical failure still occurs, have the vehicle serviced by an authorized Can-Am On-Road dealer. Fuse Locations Fuses are located in the front storage compartment. To access the fuses, open the front storage compartment.
Page 137
HOW TO REPLACE FUSES AND LIGHTS FUSE DESCRIPTION RATING 20 A Injectors / Coils 15 A Wake-up TCM, DPS / Cluster, Fuel gauge and Coolant 10 A temperature gauge H02S / CAPS / Fuel pump / 15 A EVAP / CSV, PSR rmo2014-005-023_b JCASE FUSES - LEFT FUSE BOX Left JCase Fuse Box...
2. Set the ignition switch to OFF. have them checked by an authorized Can-Am On-Road dealer. 3. Pull the fuse out. If a light described here stop working 4. Check whether the filament is on the vehicle, replace bulb of defec- melted.
Page 139
HOW TO REPLACE FUSES AND LIGHTS rmo2010-001-047_e LIGHTS LOCATION – REAR OF VEHICLE rmo2014-005-017_b 1. License plate light TYPICAL - LIGHTS LOCATION — FRONT OF 2. Backup light VEHICLE - ALL MODELS EXCEPT EUROPEAN 3. Turn signal light MODELS 1. Turn signal Japanese Models Only 2.
Page 140
HOW TO REPLACE FUSES AND LIGHTS rmr2010-038-022_a 1. Upper retaining screw 3. Remove middle retaining screws from front fascia. rmo2014-005-014_b 1. Adjustment cable retaining nuts 7. Remove all 4 headlight retaining screws. rmr2010-038-023_a 1. Middle retaining screw 4. Remove lower retaining screws and washers from front fascia.
Page 141
HOW TO REPLACE FUSES AND LIGHTS rmo2010-001-078_a rmo2010-001-079_b 1. Unplug connector 1. Turn clockwise 11. Turn the bulb counterclockwise to 14. Plug connector to the bulb. unlock it. 15. Reinstall headlight cover and re- maining parts in the reverse order of the removal.
Page 142
Fog Light (Option Package) All models except European models rmo2010-001-073_a See your authorized Can-Am On-Road 1. Unplugged connector dealer for the bulb replacement proce- dure. Turn bulb counterclockwise to unlock Position Light...
Page 143
HOW TO REPLACE FUSES AND LIGHTS rmo2010-001-082_a rmo2010-001-080_a 1. Rear panel 1. License plate lens screws 2. Retaining screws 2. Pull out the lens. 4. Pull out panel. 3. Remove the bulb by pulling it out. rmo2010-001-083 rmo2010-001-081_a 5. Unplug connector. 1.
Page 144
HOW TO REPLACE FUSES AND LIGHTS 8. Insert the new bulb into its socket then turn clockwise to lock it in posi- tion. rmo2010-001-084_b 1. Turn clockwise 9. Plug connector to the bulb. 10. Reinstall rear panel in the reverse order of the removal.
HOW TO TRANSPORT THE VEHICLE NOTICE If your vehicle needs to be transported, Do not place the strap it should be carried on a flatbed trailer over the fin. This could break it. of the proper size and capacity. 4. Attach the straps to the winch cable. If possible, use chains or additional CAUTION If you need to push straps to attach the straps to the...
Page 146
HOW TO TRANSPORT THE VEHICLE rmo2008-001-067_a TYPICAL REAR WHEEL ATTACHMENT 1. Tie-down strap rmo2008-001-069_a 2. Inside rear wheel rim ONLY TYPICAL FRONT WHEELS ATTACHMENT — METHOD 1 11. Firmly attach the rear wheel 1. Strap around the rim of each front wheel tie-down strap to the rear of the and attached to the front of trailer trailer with a ratchet.
These numbers are required by the authorized Can-Am On-Road dealer to complete warranty claims properly. We strongly recommend rmo2010-008-003_h that you take note of all the serial num-...
VEHICLE IDENTIFICATION EPA Compliance Label VEHICLE EMISSION CONTROL INFORMATION BOMBARDIER RECREATIONAL PRODUCTS INC. THIS VEHICLE CONFORMS TO U.S. EPA AND CALIFORNIA REGULATIONS APPLICABLE TO MODEL YEAR NEW MOTORCYCLES AND IS CERTIFIED TO AN HC+NOx EMISSION STANDARD OF GRAM/KILOMETER. See operator’s guide for maintenance specifications RENSEIGNEMENT SUR LE DISPOSITIF ANTIPOLLUTION BOMBARDIER PRODUITS RÉCRÉATIFS INC.
NOISE EMISSION CONTROL SYSTEM REGULATION Tampering with Noise Control Sys- tem Is Prohibited! U.S. Federal law and Canadian provin- cial laws may prohibit the following acts or the causing there of: 1. The removal or rendering inoper- ative by any person other than for purposes of maintenance, repair or replacement of any device or ele- ment of design incorporated into...
RADIO FREQUENCY DIGITALLY ENCODED SECURITY SYSTEM (RF D.E.S.S. KEY) This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any in- terference, including interference that may cause undesired operation of the device.
MULTIFUNCTION GAUGE REGULATORY INFORMATION Technical Information Changes or modifications not ex- pressly approved by the party respon- Transmitter: sible for compliance could void the – BT operating frequency range: user's authority to operate the equip- 2402 – 2480 MHz ment. –...
Page 153
MULTIFUNCTION GAUGE REGULATORY INFORMATION Brazil 03473-18-04473 Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudi- cial, mesmo de estações do mesmo tipo, e não pode causar interferên- cia a sistemas operando em caráter primário.
Page 154
MULTIFUNCTION GAUGE REGULATORY INFORMATION Hiermit erklärt Robert Bosch LLC, dass der Funkanlagentyp VIPHI2BT der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: eu-doc. bosch.com Le soussigné, Robert Bosch LLC, déclare que l'équipement radioélectrique du type VIPHI2BT est conforme à la directive 2014/53/UE.
Page 155
MULTIFUNCTION GAUGE REGULATORY INFORMATION Aš, Robert Bosch LLC, patvirtinu, kad radijo įrenginių tipas VIPHI2BT atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: eu-doc.bosch.com Ar šo Robert Bosch LLC deklarē, ka radioiekārta VIPHI2BT atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: eu-doc.bosch.com B'dan, Robert Bosch LLC, niddikjara li dan it-tip ta' tagħmir tar-radju VIPHI2BT huwa konformi mad-Direttiva 2014/53/UE.
SPECIFICATIONS MODEL SPYDER RT ENGINE ROTAX ® 1330 ACE, 4-stroke, Engine type Dual Over Head Camshaft (DOHC), liquid cooled Number of cylinders Number of valves Bore 84 mm (3.31 in) Stroke 80 mm (3.15 in) Displacement 1 330 cm³ (81.16 in³) Compression ratio 12:1 Type...
Page 157
SPECIFICATIONS MODEL SPYDER RT GEARBOX Type Sequential Electronic 6-speed with reverse interlock COOLING SYSTEM Type Liquid cooled, double radiator with cooling fans ENGINE COOLANT MAINTENANCE in the Type PROCEDURES section of this guide Coolant Capacity 4.2 L (1.1 U.S. gal.) ELECTRICAL SYSTEM Ignition system type Electronic ignition with dual output coil...
Page 158
SPECIFICATIONS MODEL SPYDER RT ELECTRICAL SYSTEM (cont'd) License plate light Backup light 2 x 21 W Day light (Limited) 2 x 0.5 W Front storage compartment light (Limited) 0.2 W HOW TO REPLACE FUSES AND LIGHTS Fuses Refer to FUEL SYSTEM Multi-point Electronic Fuel Injection (EFI) Fuel delivery Type...
Page 159
SPECIFICATIONS MODEL SPYDER RT REAR SUSPENSION (cont'd) Suspension travel 152 mm (6 in) Shock absorber Type Oil damper Preload adjustment Adjustable air pressure:135 kPa to 625 kPa (ACS with manual adjustment) (20 PSI to 90 PSI) Air controlled suspension with Preload adjustment automatic self leveling adjustment (ACS with automatic adjustment)
Page 160
SPECIFICATIONS MODEL SPYDER RT WHEELS Front 381 mm (15 in) x 127 mm (5 in) Size (diameter X width) Rear 381 mm (15 in) x 178 mm (7 in) Front wheel nuts torque 105 N•m to 113 N•m (77 lbf•ft to 83 lbf•ft) Rear drive axle nut torque 210 N•m to 240 N•m (155 lbf•ft to 177 lbf•ft) DIMENSIONS...
1. SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2019 Can-Am Spyder (the "Product") sold by authorized Can-Am On-Road Dealers ("Dealers") in the United States of America and in Canada from defects in material or work- manship for the period and under the conditions described below.
Page 163
– Damage resulting from removal of parts, improper repairs, improper service or improper maintenance, modifications, alterations that are outside of the original specifications of the Product, or damage resulting from repairs done by a person that is not an authorized servicing Dealer. –...
Page 164
5. For Products produced for sale in the state of California, that are originally sold to residents or subsequently warranty registered to residents in the state of California, please also refer to the applicable California Emissions Control Warranty Statement. The repair or replacement of parts or the performance of service under this warranty does not extend the life of this warranty beyond its original expiration date.
Page 165
In the event that service is required outside of the country of original sale, the owner will bear responsibility for any additional charges due to local practices and conditions, such as, but not limited to, freight, insurance, taxes, license fees, import duties, and any and all other financial charges, including those levied by governments, states, territories and their respective agencies.
Page 166
Under the Emissions Performance Warranty, BRP shall be liable for the total cost of the remedy for any Product validly presented for repair to any authorized Can-Am On-Road dealer, unless for emergency repairs as required by item 2 of the follow- ing list.
Page 167
Product owner or events beyond the control of BRP or an au- thorized Can-Am On-Road dealer) to repair a Product within 30 days after the initial presentation of the Product to an authorized Can-Am On-Road dealer, then the owner shall be entitled to have the warranty remedy performed, at the expense of BRP, by any repair facility of the owner’s choosing.
Page 168
BRP also warrants to the ultimate purchaser and each subsequent purchaser that this new Product, including all parts of its exhaust emission-control system and its evaporative emission-control system, meets two conditions: – It is designed, built, and equipped so it conforms at the time of sale to the ulti- mate purchaser with the requirements of 40 CFR 86 and with the evaporative emission standards of 40 CFR 1051, as applicable to onroad motorcycles.
Page 169
The California Air Resources Board and BRP US Inc. on behalf of Bombardier Recreational Products Inc., are pleased to explain the emission control system warranty on your 2019 Can-Am Spyder . In California, new motor vehicles must be designated, built and equipped to meet the State's stringent anti-smog standards.
1. SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. (“BRP”)* warrants its 2019 Can-Am Spyder (the "Products") sold by authorized Can-Am On-Road distributors or deal- ers located in the EEA (the "EEA" or "European Economic Area" shall mean the countries member of the European Union plus Norway, Iceland and Liechtenstein) or elsewhere, except in the USA and Canada** (the "Distributors/Dealers") from...
Page 171
– Tune ups and adjustments including without limitation adjustments of belt, alignment and wheel balance. – Damages related to the appearance of the Product, including without limitation scratches, dents, fading, flaking, peeling and damages to seat cover material. – Damage caused by negligence or failure to provide proper maintenance and/or OPERATOR'S GUIDE storage, as described in the –...
Page 172
For the battery, SIX (6) CONSECUTIVE MONTHS; For the tires, SIX (6) CONSECUTIVE MONTHS or until tires are worn to the last three thirty-second of an inch (3/32 ") (2.38 millimeters) for the front tires and the last five thirty-second of an inch (5/32 ") (3.97 millimeters) for the rear tire, whichever occurs first.
Page 173
6. WHAT TO DO TO OBTAIN WARRANTY COVERAGE The customer must cease using the Product upon the appearance of an anomaly. The customer must notify an authorized servicing Distributor/Dealer within two (2) months of the appearance of a defect, and provide it with reasonable access to the Product and reasonable opportunity to repair it.
Page 174
ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be re- sponsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.
PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.
CONTACT US Web Site 13B Echelon Place East Tamaki www.brp.com New Zealand, 2013 North America South America 565 de la Montagne Street Rua James Clerck Maxwell, 230 Valcourt (Québec) J0E 2L0 TechnoPark Campinas SP 13069-380 Canada Brazil Sturtevant, Wisconsin, U.S.A. 10101 Science Drive Asia Sturtevant, Wisconsin...
STOLEN UNITS: If your personal Product is stolen, you should notify BRP or an au- thorized Can-Am On-Road dealer. We will ask you to provide your name, address, phone number, the vehicle identification number and the date it was stolen.
Page 179
CHANGE OF ADDRESS/OWNERSHIP ______________...
Page 180
CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
Page 181
CHANGE OF ADDRESS/OWNERSHIP ______________...
Page 182
CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
Page 183
CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
Page 184
CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
Page 185
CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
Page 186
CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
Page 187
The Can-Am On-Road is a different type of vehicle. It requires special skills and knowledge. Learn how this product is different. BEFORE YOU OPERATE THIS VEHICLE, READ THIS OPERATOR’S GUIDE, ALL ON-PRODUCT SAFETY LABELS AND WATCH THE SAFETY VIDEO. Complete a training course (if available), practice, become proficient with the controls, and get a proper license.