Table of Contents

Advertisement

Quick Links

RENEGADE
®
Series
WARNING
Read this guide thoroughly.
It contains important safety information.
Minimum recommended age: Operator: 16 years old.
Keep this Operator's Guide in the vehicle.
2 1 9 0 0 2 0 9 5
Original Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 219 002 095 and is the answer not in the manual?

Questions and answers

Summary of Contents for Can-Am 219 002 095

  • Page 1 RENEGADE ® Series WARNING Read this guide thoroughly. It contains important safety information. Minimum recommended age: Operator: 16 years old. Keep this Operator’s Guide in the vehicle. 2 1 9 0 0 2 0 9 5 Original Instructions...
  • Page 2 (BRP). In USA, products are distributed by BRP US Inc. ® D.E.S.S.™ DPS™ Renegade™ Rotax ® TTI™ X™ XPS™ Can-Am † Visco-Lok is a trademark of GKN Viscodrive GmbH. 219002095 en COJT ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates.
  • Page 3: Foreword

    FOREWORD OPERATOR'S GUIDE 2021 Renegade 570 Renegade 850 Renegade X xc 650 Renegade X xc 850 Renegade X xc 1000R Dieses Handbuch ist möglicherweise in Ihrer Landessprache Deutsch verfügbar. Bitte wenden Sie sich an Ihren Händler oder besuchen Sie: www.operatorsguides.brp.com This guide may be available in your language.
  • Page 4: Know Before You Go

    This vehicle is a category S, always fol- BRP warranty and a network of autho- low this age recommendation: rized Can-Am dealers ready to provide – A person under 16 years old should the parts, service or accessories you never operate this vehicle.
  • Page 5: About This Operator's Guide

    FOREWORD NOTICE Indicates an instruction which, if not followed, could se- verely damage vehicle components or other property. About this Operator's Guide This Operator's Guide has been pre- pared to acquaint the owner/operator of a new vehicle with the various ve- hicle controls, maintenance and safe operating instructions.
  • Page 6: Table Of Contents

    TABLE OF CONTENTS FOREWORD ................1 Know Before you Go ..
  • Page 7 TABLE OF CONTENTS CONTROLS (cont’d) 4) Brake Pedal ..............73 5) Shift Lever ..
  • Page 8 TABLE OF CONTENTS MAINTENANCE MAINTENANCE SCHEDULE ............ 104 SEVERE DUSTY CONDITIONS ..
  • Page 9 MULTIFUNCTION GAUGE MESSAGES ........161 WARRANTY BRP LIMITED WARRANTY USA AND CANADA: 2021 CAN-AM ®...
  • Page 10 TABLE OF CONTENTS _______________...
  • Page 11: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...
  • Page 12: General Precautions

    GENERAL PRECAUTIONS Avoid Carbon Monoxide – For refueling, strictly adhere to in- FUEL structions in Poisoning – Never start or operate the engine if All engine exhaust contains carbon the fuel cap is not properly installed. monoxide, a deadly gas. Breathing car- bon monoxide can cause headaches, Gasoline is poisonous and can cause dizziness, drowsiness, nausea, confu-...
  • Page 13: Special Safety Messages

    SPECIAL SAFETY MESSAGES THIS VEHICLE IS NOT A TOY AND CAN BE HAZARDOUS TO OPERATE. – This vehicle handles differently from other vehicles including motorcycles and cars. A collision or rollover can occur quickly, if you fail to take proper precautions, even during routine maneuvers such as turning and driving on hills or over obstacles.
  • Page 14 SPECIAL SAFETY MESSAGES – Always follow proper procedures for going down hills and for braking on hills as RIDING TECHNIQUES described in . Check the terrain carefully before you start down any hill. Never go down a hill at high speed. Avoid going down a hill at an angle that would cause the vehicle to lean sharply to one side.
  • Page 15: Operation Warnings

    Beginners and inexperienced operators should complete a training course. They should then regularly practice the skills learned during the course as well as the operating techniques described in this Operator's Guide. For more information about a training course, contact an authorized Can-Am dealer. ________ ________ SAFETY INFORMATION...
  • Page 16 OPERATION WARNINGS WARNING V00A1AQ POTENTIAL HAZARD Failure to follow the age recommendations for this vehicle. WHAT CAN HAPPEN A lack of respect for this age recommendation can lead to severe injury or death of the child. Even though a child may be within the age group for which this vehicle is recommended, he may not have the skills, abilities, or judgment needed to operate this vehicle safely and may be involved in a serious accident.
  • Page 17 OPERATION WARNINGS WARNING V00A02Q POTENTIAL HAZARD Carrying a passenger on this vehicle. WHAT CAN HAPPEN Greatly reduces your ability to balance and control this vehicle. Could cause an accident, resulting in harm to you and/or your passenger. HOW TO AVOID THE HAZARD Never carry passenger.
  • Page 18 OPERATION WARNINGS WARNING V00A2DQ POTENTIAL HAZARD Allowing passenger to sit in any location on this vehicle. WHAT CAN HAPPEN Allowing a passenger could: – Impair vehicle stability which could lead to a loss of control. – Result in injury to passenger from impact on hard surfaces. –...
  • Page 19 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle on public streets, roads or highways. WHAT CAN HAPPEN You can collide with another vehicle. HOW TO AVOID THE HAZARD Never operate this vehicle on any public street, road or highway, even a dirt or gravel one.
  • Page 20 OPERATION WARNINGS WARNING POTENTIAL HAZARD Riding this vehicle without wearing an approved helmet, eye protection and protective gear. WHAT CAN HAPPEN – Riding without an approved helmet increases the chances of a severe head injury or death in the event of an accident. –...
  • Page 21 OPERATION WARNINGS WARNING V00A07Q POTENTIAL HAZARD Using this vehicle with drugs or alcohol. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death. HOW TO AVOID THE HAZARD Never use this vehicle with drugs or alcohol.
  • Page 22 OPERATION WARNINGS WARNING V00A08Q POTENTIAL HAZARD Operating this vehicle at excessive speeds. WHAT CAN HAPPEN Increases your chances of losing control of the vehicle, which can result in an accident. HOW TO AVOID THE HAZARD Always travel at a speed which is appropriate for the terrain, visibility and operating conditions, and your experience.
  • Page 23 OPERATION WARNINGS WARNING POTENTIAL HAZARD Attempting wheelies, jumps and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, including an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps. Do not try to show off. WARNING POTENTIAL HAZARD Failure to inspect the vehicle before operating.
  • Page 24 OPERATION WARNINGS WARNING POTENTIAL HAZARD Riding on frozen waterways. WHAT CAN HAPPEN Breaking through the ice can lead to severe injury or death. HOW TO AVOID THE HAZARD Never ride this vehicle on a frozen surface before you are sure the ice is thick enough and sound enough to support the vehicle and its load, as well as the force that is created by a moving vehicle.
  • Page 25 OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to use extra care when operating this vehicle on unfamiliar terrain. WHAT CAN HAPPEN You can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning or loss of control. HOW TO AVOID THE HAZARD Go slowly and be extra careful when operating on unfamiliar terrain.
  • Page 26 OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an acci- dent, including an overturn. HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control this vehicle on...
  • Page 27 OPERATION WARNINGS WARNING POTENTIAL HAZARD Turning improperly. WHAT CAN HAPPEN Vehicle could go out of control, causing a collision or an overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for turning as described in this Operator's Guide. Practice turning at low speeds before attempting to turn at faster speeds.
  • Page 28 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating on excessively steep hills. WHAT CAN HAPPEN The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. HOW TO AVOID THE HAZARD Never operate this vehicle on hills too steep for the vehicle or for your abili- ties.
  • Page 29 OPERATION WARNINGS WARNING POTENTIAL HAZARD Climbing hills improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for climbing hills as described in this Op- erator's Guide. Always check the terrain carefully before you start up any hill.
  • Page 30 OPERATION WARNINGS WARNING POTENTIAL HAZARD Going down a hill improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for going down hills as described in this Operator's Guide.
  • Page 31 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly crossing hills or turning on hills. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Never attempt to turn the vehicle around on any hill until you have mastered the turning technique as described in this Operator's Guide on level ground.
  • Page 32 OPERATION WARNINGS WARNING POTENTIAL HAZARD Stalling, rolling backwards or improperly dismounting while climbing a hill. WHAT CAN HAPPEN Could result in vehicle overturning. HOW TO AVOID THE HAZARD Use proper gear and maintain steady speed when climbing a hill. If you lose all forward speed: Keep your weight uphill.
  • Page 33 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly operating over obstacles. WHAT CAN HAPPEN Could cause loss of control, or a collision. Could cause the vehicle to overturn. HOW TO AVOID THE HAZARD Before operating in a new area, check for obstacles. Never attempt to ride over large obstacles, such as large rocks or fallen trees.
  • Page 34 OPERATION WARNINGS WARNING POTENTIAL HAZARD Skidding or sliding improperly. WHAT CAN HAPPEN You may lose control of this vehicle. You may also regain traction unexpectedly, which may cause the vehicle to overturn. HOW TO AVOID THE HAZARD Learn to safely control skidding or sliding by practicing at low speeds and on level smooth terrain.
  • Page 35 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle through deep or fast flowing water. WHAT CAN HAPPEN Tires may float, causing loss of traction and loss of control, which could lead to an accident. HOW TO AVOID THE HAZARD Never operate this vehicle in fast flowing water or in deep water. Check water depth and current before you attempt to cross any water.
  • Page 36 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly operating in reverse. WHAT CAN HAPPEN You could hit an obstacle or person behind the vehicle, resulting in serious injury. HOW TO AVOID THE HAZARD When you select reverse gear, make sure there are no obstacles or people behind the vehicle.
  • Page 37 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle with improper tires, or with improper or uneven tire pressure. WHAT CAN HAPPEN Use of improper tires on this vehicle, or operation of this vehicle with improper or uneven tire pressure, may cause loss of control, tire blow outs, tire to move around on its rim, and increases the risk of an accident.
  • Page 38 All parts and accessories added to this vehicle should be approved by BRP and should be installed and used according to instructions. If you have questions, consult an authorized Can-Am dealer. NEVER install a passenger seat or use the racks to carry a passenger.
  • Page 39 OPERATION WARNINGS WARNING POTENTIAL HAZARD Overloading this vehicle, carrying or towing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle handling which could lead to an accident. HOW TO AVOID THE HAZARD Never exceed the stated load capacity for this vehicle including operator as well as other loads and added accessories.
  • Page 40 OPERATION WARNINGS WARNING V03M01Q POTENTIAL HAZARD Transporting flammable or dangerous material can lead to explosions. WHAT CAN HAPPEN This can cause serious injury or death. HOW TO AVOID THE HAZARD Never transport flammable or dangerous material. _______ ________ SAFETY INFORMATION...
  • Page 41: Important On-Product Labels(Canada/United States)

    IMPORTANT ON-PRODUCT LABELS (CANADA/UNITED STATES) Canada/United States Hang Tag This vehicle comes with a hang tag and labels containing important safety and emission informations. 704903318 TYPICAL ________ ________ SAFETY INFORMATION...
  • Page 42 IMPORTANT ON-PRODUCT LABELS(CANADA/UNITED STATES) . Operating, servicing and WARNING maintaining an off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
  • Page 43: Vehicle Safety Labels

    • avoid paved surfaces - pavement may seriously affect handling and control. Read and understand all safety labels, locate and read operator's guide and watch the safety video using the QR code link or visit Can-am web site before operation. LOCATE AND READ OPERATOR’S GUIDE FOLLOW ALL INSTRUCTIONS &...
  • Page 44 IMPORTANT ON-PRODUCT LABELS(CANADA/UNITED STATES) •ATV MUST be stopped UNDER before shifting lever. •ALWAYS apply foot brake to shift from Park (P) and Operating this ATV if you are under the Neutral (N). 704906054 age16 increases the chance of SEVERE INJURYor DEATH. NEVER NEVER operate this ATV if you are...
  • Page 45 IMPORTANT ON-PRODUCT LABELS(CANADA/UNITED STATES) maintain proper tire pressure according to the load on the vehicle. Refer to table. ALWAYS use the trailer hitch underinflate tire as it could or the recovery hook to pull cause the tire to disloge from the rim. a load.
  • Page 46: Compliance Labels

    IMPORTANT ON-PRODUCT LABELS(CANADA/UNITED STATES) Compliance Labels Technical Information Labels These labels indicate vehicle's compli- ance. Bombarider Recreational Products Inc. certifies that this ATV complies with ANSI / SVIA-1-2017 Standard. Unleaded fuel only Bombardier Produits Récréatifs inc. certifie que ce VTT est conforme à la norme Recommended: ANSI / SVIA-1-2017 Standard.
  • Page 47: Important On-Product Labels

    If missing or damaged, vmo2012-014-903_c they can be replaced free of charge. See an authorized Can-Am dealer. NOTE: In the event of any discrep- ancy between this guide and the ve- hicle, the safety labels on the vehicle have precedence over the labels in this guide.
  • Page 48 DEATH. Follow all instructions and warnings. – Never use on public roads. – Never carry a passenger. – Never use with drugs or alcohol. Safety Video 704905679 https:// can-am.brp.com EN-704905679-DEC /off-road/safety LABEL 3 L L abel 4 Patent : www.brp.com/en/about-brp/patents.html 8012 WARNING...
  • Page 49 IMPORTANT ON-PRODUCT LABELS (ALL COUNTRIES EXCEPT CANADA/UNITED STATES) Label 5 L L abel 6 WARNING WARNING – Locate and read operator's – NEVER carry a passenger on guide. Improper tire pressure this carrier. and overloading can cause loss – MAXIMUM REAR LOAD: 23 kg of control, resulting in SEVERE (50 lb) evenly distributed (in- INJURY or DEATH.
  • Page 50: Compliance Labels

    IMPORTANT ON-PRODUCT LABELS (ALL COUNTRIES EXCEPT CANADA/UNITED STATES) Compliance Labels Label 8 These labels indicate vehicle's compli- ance. EMISSION CONTROL INFORMATION vmo2010-010-100_a LABEL 8 Label 9 WARNING Do not open when hot. EN-EPA-DEC TYPICAL: WHEN APPLICABLE - UNDER SEAT 704907278-DEC NEAR GAS CAP 704905706 EN-704905706-DEC...
  • Page 51: Technical Information Labels

    IMPORTANT ON-PRODUCT LABELS (ALL COUNTRIES EXCEPT CANADA/UNITED STATES) Technical Information Labels Unleaded fuel only Recommended: PREMIUM 91 (min (R+M)/2) SUPER 95 704907508 (min RON) EN-704907508-DEC LOCATED NEAR GAS CAP OF 1000R ENGINES 707800373 UNDER SEAT ________ ________ SAFETY INFORMATION...
  • Page 52: Reporting Safety Defects

    REPORTING SAFETY DEFECTS In Canada, if you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada in addition to notifying Bombardier Recreational Products Inc. If Transport Canada receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
  • Page 53: Pre-Ride Inspection

    PRE-RIDE INSPECTION WARNING Perform a pre-ride inspection be- fore each ride to detect any po- tential problem that could occur during operation. The pre-ride inspection can help you monitor component wear and deteriora- tion before they become a prob- lem. Correct any problem that you discover to reduce the risk of a breakdown or crash.
  • Page 54: Pre-Ride Inspection Check List

    PRE-RIDE INSPECTION Pre-Ride Inspection Check List What to Do Before Starting the Engine (Unpowered Electrical System) ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Engine oil Check engine oil level. Coolant Check coolant level. Brake fluid Check brake fluid level. Leaks Check for any leaks under vehicle Throttle lever...
  • Page 55 PRE-RIDE INSPECTION What to Do Before Starting the Engine (Electrical System Powered) ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Multifunction gauge Check operation of indicator lamps in multifunction gauge (during first few seconds of key ON) Check for messages on multifunction gauge Lights Check operation and cleanliness of headlights and taillight Check operation of low and high beams...
  • Page 56: Riding The Vehicle

    Please take the time to study this Operator's Guide and all on-product safety labels SAFETY VIDEO as well as the located at https://can-am.brp.com/off-road/safety. They more completely describe what you should know about this vehicle before riding it. Whether you are a new user or an experienced rider, it is important for your personal safety that you know the controls and features of this vehicle.
  • Page 57: Riding Gear

    RIDING THE VEHICLE Riding Gear Actual weather conditions should help you decide how to dress. Dress for the coldest weather expected. Thermal underwear next to the skin also provides a good insulation. It is important that the operator always wears the appropriate protective riding gear and apparel, including an approved helmet, eye protection, boots, gloves, a long sleeved shirt and pants.
  • Page 58: Environment

    RIDING THE VEHICLE users on the trail. Always stay to the complete right of the trail and do not zigzag to one side of the trail then the other. Be prepared to stop or pull off to the side if another trail user appears in front of you.
  • Page 59: Design Limitation

    RIDING THE VEHICLE Finally, do not pollute streams, lakes or rivers and do not modify the engine or ex- haust system, or remove any of its components. Design Limitation Although the vehicle is exceptionally rugged for its class, it is still a light vehicle by definition and its operation must be restricted to its proper purpose.
  • Page 60 RIDING THE VEHICLE Body Position To maintain proper control, it is strongly advised that you keep your hands on the handlebar and within easy reach of all controls. The same holds true for your feet on the foot pegs. To minimize the possibility of a leg or foot injury, keep your feet on the foot pegs at all times.
  • Page 61 RIDING THE VEHICLE To reduce the risk of rollovers: – Use care when turning. • Do not turn the handlebar too far or too fast for your speed and environment. Adjust steering inputs accordingly. • Slow down before entering a turn. Avoid hard braking during a turn. •...
  • Page 62 RIDING THE VEHICLE Braking Always keep both hands on handlebars and feet on foot pegs when braking. Practice braking to get familiar with the brake response. – Do it at low speed first, then increase the speed. – Practice braking in straight line at different speeds and different braking force. –...
  • Page 63 RIDING THE VEHICLE Uphill Driving Before trying to climb a hill, keep these things in mind. Hill Climbing should only be attempted by experienced operators. Start on shallow slopes. Always drive straight uphill and keep your body weight forward towards the top of the hill. Keep your feet on the footrests, shift your ATV into a lower gear and accelerate before you start to climb.
  • Page 64 RIDING THE VEHICLE Downhill Driving This vehicle can climb slopes that are steeper than it can safely descend. There- fore, it is essential to ensure that a safe route exists to descend a slope before you climb it. Decelerating while negotiating a slippery downhill slope could “toboggan” the ve- hicle.
  • Page 65 RIDING THE VEHICLE Side Hilling This is one of the most risky types of riding since it may drastically change the bal- ance of the vehicle. It should be avoided whenever possible. However, if it is nec- essary to do so , it is important that you ALWAYS keep your body weight on the up- side of the slope and be prepared to dismount on that side should the vehicle begin to topple.
  • Page 66 RIDING THE VEHICLE Crossing Water Water can be a unique hazard. If it is too deep the vehicle may “float” and topple. Check the water depth and current before you attempt to cross any water. Water should not go above the footrest. Be wary of slippery surfaces such as rocks, grass, logs, etc., both in the water and on its banks.
  • Page 67 RIDING THE VEHICLE Whenever an ATV is ridden on a snow covered drive path the tire grip is generally reduced causing the vehicle to react differently to control inputs from the operator. On low grip surfaces, the steering responses are not as crisp and precise, stopping distances are lengthened and acceleration becomes sluggish.
  • Page 68 RIDING THE VEHICLE When riding in sand dunes it is advisable to equip the vehicle with an antenna type safety flag. This will help make your location more visible to others over the next sand dune. Proceed carefully should you see another safety flag ahead. Since the antenna type safety flag can snag and rebound on your body if caught, do not use it in areas where there are low hanging branches or obstacles.
  • Page 69: Moving Loads And Doing Work

    Your vehicle can help you perform a number of different LIGHT tasks ranging from snow removal to pulling wood or carrying cargo. A variety of accessories are avail- able from your authorized Can-Am dealer. To prevent possible injury, follow the in- structions and warnings that accompany the accessory. Always respect the load limits of the vehicle.
  • Page 70 MOVING LOADS AND DOING WORK EXAMPLE OF LOAD DISTRIBUTION TOTAL TONGUE VEHICLE OPERATOR CARGO LOAD ACCESSORIES WEIGHT LOAD 141 kg (310 lb) 108 kg (238 lb) 9 kg (20 lb) 10 kg (22 lb) 13 kg (30 lb) Loading the Rear Cargo Area Load cargo as low as possible –...
  • Page 71 MOVING LOADS AND DOING WORK WARNING A slack in the chain or cable can cause it to break and snap back. When pulling another vehicle, be sure that someone is controlling the pulled vehi- cle. They must brake and steer to prevent the vehicle from going out of control. Before pulling loads with a winch, refer to the winch manufacturer’s instructions.
  • Page 72 MOVING LOADS AND DOING WORK This page is intentionally blank _______ ________ SAFETY INFORMATION...
  • Page 73: Vehicle Information

    VEHICLE INFORMATION _______________...
  • Page 74: Controls

    CONTROLS 219002095-001 1) Throttle Lever The throttle lever is located on the RH side of the handlebar. The throttle lever controls the engine speed. To increase or maintain vehicle speed, press the throttle lever with your right thumb. To decrease vehicle speed, release the throttle lever.
  • Page 75: Lh Brake Lever

    CONTROLS 2) LH Brake Lever The LH brake lever is located on the LH side of the handlebar. 219001872-001_a Step 1: Apply brakes Step 2: Lock brakes NOTE: The parking brake lever can be set in several positions. V07K01Y WARNING TYPICAL Ensure when the parking brake is 1.
  • Page 76: Shift Lever

    CONTROLS The brake pedal function is to slow down or stop the vehicle. When the brake pedal is pressed down, only the rear brake is applied. Braking effect is proportional to the force applied on the pedal. NOTE: The brake will have also an ef- fect on front wheels through the drive vmo2012-012-036 train when 4WD is engaged.
  • Page 77: Keys

    The vehicle is delivered with 1 perfor- The D.E.S.S. of your vehicle can be pro- mance key. grammed by your authorized Can-Am NOTE: Additional keys are available dealer to accept up to 8 different keys. from your dealer as an accessory.
  • Page 78: Multifunction Switch

    If you have more than one D.E.S.S. Engine Stop Switch equipped Can-Am vehicle, each can be programmed by your authorized Can-Am dealer to accept the other ve- hicle D.E.S.S. keys. 7) Multifunction Switch The multifunction switch is located on the LH side of the handlebar.
  • Page 79: 2Wd/4Wd And Driving Modes (If Equipped) Selector Switch

    CONTROLS Override/DPS Button 2. Press and hold the override/DPS button then press the throttle lever Depending on the vehicle model, this gradually. button has up to 2 functions. NOTE: When using the override func- Override Function tion, the gauge will scroll an OVER- RIDE message to confirm that the function is activated.
  • Page 80 CONTROLS 219001961-004_a 219001961-004_c TYPICAL TYPICAL - 2WD MODE 1. 2WD/4WD Selector 2. 2WD position This switch is used to select the driving 3. 4WD position modes. (If equipped) 4. Driving modes selector Bring the vehicle to a complete stop with the engine idling before changing between 2WD and 4WD modes or the opposite.
  • Page 81 CONTROLS NOTE: The SPORT mode can be acti- vated with all key types and provides the maximum power with the used key. The ECO mode provides a smoother throttle response and is limited to a maximum speed of 70 km/h (43 MPH). Press LEFT to activate, RIGHT to deac- tivate.
  • Page 82: Digital Display

    4.5" DIGITAL DISPLAY Multifunction Display Left Lateral Display Lower Display 219001961-711 The left lateral display includes: 219001961-710 – Fuel level indicator May display the following: – 2X4 / 4X4 telltale – RPM – Speed – Engine Temperature – Battery Voltage –...
  • Page 83: Warning Lamps And Indicators

    4.5" DIGITAL DISPLAY Central Display The MODE display indicates the se- lected mode of operation: – SPORT – ECO A message of the selected mode will be displayed on the lower display at activation and deactivation as follow: MESSAGE DRIVE MESSAGE AT MODE DEACTIVATION...
  • Page 84: Settings

    4.5" DIGITAL DISPLAY NOTE: Some warning indicators ap- Icons and Indicators - Multifunction pear in the display of the multifunction Display gauge and function the same as an in- ICONS AND INDICATORS dicator lamp but do not display when starting the vehicle. Denotes SPORT mode is selected.
  • Page 85 (minutes flash). 8. Press LOWER (MENU) button to ac- knowledge minutes. Setting Language The gauge display language can be changed. Refer to an authorized Can-Am dealer for language availability and to setup the gauge to your prefer- ence. _______________...
  • Page 86: Equipment

    EQUIPMENT 219002021-004 ______________...
  • Page 87: Seat

    EQUIPMENT 1) Seat Seat Installation The seat is designed for an operator Position front end of seat so that the only. front retaining device under the seat engages with the retaining bar. When seat rests in its position, firmly push WARNING seat down to latch.
  • Page 88: Footpegs

    EQUIPMENT 2) Footpegs 4) Rear Cargo Area The footpegs are located on the RH Rear cargo area is convenient for carry- and LH footrests. ing small articles. Secure cargo using the eyelets. vmo2012-014-007_a vmo2012-014-002_a 1. Cargo area TYPICAL 2. Plastic eyelets 1.
  • Page 89: Recovery Hook

    EQUIPMENT 6) Recovery Hook 8) Console Convenient hook that can be used to Console Removal recover a stuck ATV. 1. See procedures in this section and remove: – Seat – Gauge support 2. At front of console, pull both lugs out of their grommets.
  • Page 90: Fuel

    FUEL Fuel Requirements NOTICE Always use fresh gaso- line. Gasoline will oxidize; the re- sult is loss of octane, volatile com- pounds, and the production of gum NOTICE Never experiment with and varnish deposits which can other fuels. Engine or fuel system damage the fuel system.
  • Page 91 FUEL vmo2012-014-004_a 1. Fuel reservoir cap WARNING If a differential pressure condition is noticed (whistling sound heard when loosening fuel reservoir cap) have vehicle inspected and/or re- paired before further operation. 4. Insert the spout into the filler neck. 5. Pour fuel slowly so that air can es- cape from the tank and prevent fuel flow back.
  • Page 92: Break-In Period

    BREAK-IN PERIOD Operation During Break-In A break-in period of 300 km (200 mi) or 10 operating hours is required for the vehicle. Engine During the break-in period: – Avoid full throttle operation – Maximum throttle should not ex- ceed 3/4 –...
  • Page 93: Basic Procedures

    BASIC PROCEDURES Starting the Engine Changing Gear Selection The shift lever must be set to PARK or Apply brakes and immobilize vehicle, NEUTRAL. then select the desired shift lever posi- tion. NOTE: For your convenience, an over- ride mode allows the engine to be Release brakes.
  • Page 94 BASIC PROCEDURES Push the engine stop switch to OFF po- sition. Remove D.E.S.S. from D.E.S.S. post. If you must park on a steep incline or if the vehicle is carrying cargo, block the wheels using rocks or bricks. ______________...
  • Page 95: Special Procedures

    – Fuel tank breather replacement NOTICE authorized – Lubricant inspection and replace- Can-Am dealer to have the CVT in- ment as required (engine, gearbox spected and cleaned. and rear final drive). Reinstall the drain plug and secure it...
  • Page 96: What To Do If Vehicle Is Turned Over

    Do not use any electrical equipment while ve- hicle is immersed. It will be necessary to take the vehicle to an authorized Can-Am dealer as soon as possible. NEVER ATTEMPT TO START THE ENGINE! NOTICE Immersion of the vehi-...
  • Page 97: Tune Your Ride

    TUNE YOUR RIDE WARNING REAR SUSPENSION FACTORY PRELOAD SETTINGS Suspension adjustment could af- fect vehicle handling. Always take FACTORY ADJUSTMENT MODEL time to familiarize yourself with SETTING the vehicle's behavior after any suspension adjustment have been position 3 made. Spring preload 850 / 63.1 mm Suspension Adjustments...
  • Page 98 TUNE YOUR RIDE Shock Damping Compression Damping Adjustments (X xc Models) Compression damping controls how the shock absorber restrains the com- pression stroke. vmo2012-014-060_a 219001868_009_a TYPICAL COMPRESSION DAMPING - TOP OF SHOCK Step 1: Loosen top locking ring ABSORBER Step 2: Turn adjusting ring accordingly 1.
  • Page 99: Dynamic Power Steering (Dps) Assist Level Adjustment (X Xc Models)

    TUNE YOUR RIDE DPS MODE Maximum steering assist MAX. Medium steering assist MED. Minimum steering assist MIN. 219001868_010_a REBOUND DAMPING - BOTTOM OF SHOCK To show the active DPS mode, pro- ABSORBER ceed as follows: 1. Increase (firmer) 2. Decreases (softer) 1.
  • Page 100 TUNE YOUR RIDE To change the DPS mode, proceed as follows: 1. Press and hold Override/DPS but- ton for 2 seconds to go to the next setting. 2. Release Override/DPS button. 3. Repeat until desired setting is se- lected. NOTE: The DPS assist adjustment is not available in reverse.
  • Page 101: Transporting The Vehicle

    TRANSPORTING THE VEHICLE When contacting a towing or trans- SAFETY PRECAUTIONS porting service, be sure to ask if they Ensure you have a good have a flatbed trailer, loading ramp or Visibility visibility during the entire power ramp to safely lift the vehicle maneuver.
  • Page 102: Using A Winch To Pull Vehicle Onto Trailering Equipment

    TRANSPORTING THE VEHICLE 3. Back off the vehicle, verify ramps 3. If the vehicle is not equipped with a are still secure, then proceed at winch, proceed as follows: proper speed. 3.1 Attach strap to lower front 4. Carefully drive vehicle onto platform bumper anchor.
  • Page 103: Getting Vehicle Out Of Trailer

    TRANSPORTING THE VEHICLE 219002095-002 FRONT TIE-DOWN POINT LOCATION vmo2013-007-003_a TYPICAL 1. Rear tie-down point location NOTICE Securing vehicle at other locations may damage the vehicle. Getting vehicle out of trailer WARNING Vehicle may have moved during transport. Ensure vehicle is prop- erly aligned with ramps before proceeding.
  • Page 104 TRANSPORTING THE VEHICLE This page is intentionally blank ______________...
  • Page 105 MAINTENANCE ______________...
  • Page 106: Maintenance

    Although an authorized Can-Am Off-Road dealer has an in-depth technical knowl- edge and tools to service your vehicle, the emission-related warranty is not condi- tioned on the use of an authorized Can-Am Off-Road dealer or any other establish- ment with which BRP has a commercial relationship.
  • Page 107: Maintenance Schedule Legend

    MAINTENANCE SCHEDULE MAINTENANCE SCHEDULE LEGEND Operation in trail riding conditions Operation in severe riding conditions (dusty or muddy) or carrying heavy loads condition MAINTENANCE SCHEDULE Make sure to perform proper maintenance at recommended intervals as indicated in the tables. Some items of the maintenance schedule must be performed in function of the calendar, regardless of the distance or time of operation.
  • Page 108 MAINTENANCE SCHEDULE EVERY 3 000 KM (2,000 MI) OR 100 HOURS (whichever comes first) EVERY 1 500 KM (1,000 MI) OR 50 HOURS (whichever comes first) Lubricate throttle cable (Renegade 570 only) Inspect and clean brake system Inspect battery condition Verify steering system for abnormal play Verify front differential and rear final drive oil level and look for contamination Verify gearbox oil level and look for contamination...
  • Page 109 MAINTENANCE SCHEDULE EVERY 12 000 KM (8,000 MI) OR 5 YEARS (whichever comes first) EVERY 6 000 KM (4,000 MI) OR 5 YEARS (whichever comes first) Replace engine coolant ______________...
  • Page 110: Maintenance Procedures

    MAINTENANCE PROCEDURES This section includes instructions for 2. Lift the front part of the central basic maintenance procedures. panel. WARNING Unless otherwise indicated, al- ways remove D.E.S.S. key before performing any maintenance. WARNING Should removal of a locking de- vice be required (e.g. lock tab, vmo2008-005-002_a self-locking fastener, etc.), always TYPICAL...
  • Page 111 MAINTENANCE PROCEDURES vmr2012-010-017_b vmo2012-012-038 TYPICAL - SOME PARTS REMOVED FOR AIR FILTER REMOVAL CLARITY 1. Air filter drain tube Engine Air Filter Housing Inspection and Draining Air Filter Cleaning and Oiling 1. Remove LH side panel. Paper Filter Cleaning 2. Drain air filter housing inlet drain 1.
  • Page 112 MAINTENANCE PROCEDURES vbs2009-012-014 vbs2009-012-015_a TYPICAL - OIL THE FOAM FILTER TYPICAL - SPRAY THE FOAM FILTER 2. Let stand for 3 to 5 minutes. 2. Dry the foam filter completely. 3. Remove any excess of oil that could transfer to the paper filter by wrapping the foam filter into an ab- sorbent cloth and squeezing gently.
  • Page 113: Engine Oil

    MAINTENANCE PROCEDURES – Gauge support – Seat. Engine Oil Engine Oil Level NOTICE Check level frequently and refill if necessary. Do not over- fill. Operating the engine/gearbox with an improper level may severely damage engine/gearbox. Wipe off V07C02B any spillage. TYPICAL 1.
  • Page 114: Oil Filter

    MAINTENANCE PROCEDURES Ensure vehicle is on a level surface. XPS RECOMMENDED ENGINE OIL Remove dipstick. Scandinavia: 4T 5W40 SYNTHETIC Clean the oil drain plug area. BLEND OIL (EUR) Place a drain pan under the oil drain (P/N 779290) General plug area. purpose Other Countries: Unscrew oil drain plug.
  • Page 115: Radiator

    WHEN RINSING, USE LOW PRESSURE ONLY, NEVER USE A Radiator HIGH PRESSURE WASHER. See an authorized Can-Am deal er, re- Radiator Inspection pair shop or person of your own choos- Periodically check the radiator area for ing to check the performance of the cleanliness.
  • Page 116: Engine Coolant

    NOTE: A cooling system that fre- quently requires coolant is the indica- tion of leaks or engine problems. See an authorized Can-Am dealer. vmo2008-005-002_a Reinstall: TYPICAL 1. Lift here –...
  • Page 117 MAINTENANCE PROCEDURES NOTICE 570 and 650 Models Always use ethylene-gly- col antifreeze containing corrosion Disconnect the lower radiator hose inhibitors specifically for internal and drain the remaining coolant into a combustion aluminum engines. suitable container. NOTE: Take note of hose clamp posi- Engine Coolant Replacement tion on the lower radiator hose.
  • Page 118: Muffler Spark Arrester

    MAINTENANCE PROCEDURES Muffler Spark Arrester Muffler Spark Arrester Cleaning and Inspection NOTE: Spark arrester screen replace- ment is required only when damaged. CAUTION Let exhaust system cool down before proceeding with cleaning and inspection. Remove and discard the tail pipe retain- tmo2011-001-502_a ing screws.
  • Page 119: Cvt Air Filter

    MAINTENANCE PROCEDURES NOTICE CVT Air Filter Use a soft brush and be careful to avoid damaging spark ar- rester mesh. CVT Air Filter Removal 1. Remove gauge support. Refer to CAUTION Wear eye protection EQUIPMENT and gloves. 2. Remove air filter from CVT air inlet by stretching its sides.
  • Page 120: Gearbox Oil

    MAINTENANCE PROCEDURES Gearbox Oil Recommended Gearbox Oil RECOMMENDED GEARBOX OIL Gearbox Oil Level Verification 75W140 NOTICE Check level and refill if SYNTHETIC necessary. Do not overfill. Operat- Scandinavia GEAR OIL (EUR) ing the gearbox with an improper (P/N 779215) level may severely damage gear- box.
  • Page 121: Throttle Body

    MAINTENANCE PROCEDURES TIGHTENING TORQUE 5 N•m ± 0.6 N•m Oil level plug (44 lbf•in ± 5 lbf•in) Wipe off any spillage. Dispose gearbox oil as per your local environmental regulations. vmo2012-012-056_a Throttle Body TYPICAL - 570/850 ENGINE 1. Drain plug 2.
  • Page 122: Throttle Cable (If Equipped)

    MAINTENANCE PROCEDURES CAUTION Use the product in a well ventilated area. Refer to prod- uct manufacturer's warnings. 5. To avoid getting dirt into engine, spray cleaner on a clean rag then rub rag against throttle plate and bore. A toothbrush may also be used. CAUTION Ensure key is re- moved so that nobody can acti- vate the electrical system, otherwise...
  • Page 123 MAINTENANCE PROCEDURES vmo2006-007-032_a 1. Throttle body V07I0HY 2. Side cover screws 1. Inner housing protector Insert the needle of the lubricant can in Remove the cable from the throttle the end of throttle cable adjuster. lever housing. NOTE: Slide cable in clip slot and re- CAUTION Always wear move the end of cable from clip.
  • Page 124: Spark Plugs

    MAINTENANCE PROCEDURES Spark Plugs Spark Plug Access Remove side panels. Unplug spark plug cables. Spark Plug Removal Unscrew spark plugs one turn. CAUTION Always wear safety V07I0GY goggles when using pressurized air. 1. Cable protector Clean spark plugs and cylinder heads 2.
  • Page 125: Cvt Cover

    MAINTENANCE PROCEDURES Spark Plug Installation WARNING Prior to installation, make sure that Engine must be cool before cover contact surfaces of cylinder heads and is removed. Always wear protec- spark plugs are free of grime. tive gloves when removing cover. Using a feeler gauge, set the spark plug gap.
  • Page 126: Cvt Cover Installation

    MAINTENANCE PROCEDURES Open driven pulley. REQUIRED TOOL PULLER/LOCKING TOOL (P/N 529 036 098) Screw tool in the threaded hole of driven pulley and tighten to open the pulley. Vmr2012-018-004_a 1. CVT cover screw 2. CVT cover 3. Gasket CVT Cover Installation Install the center top screw of first.
  • Page 127: Drive And Driven Pulleys

    1. Lowest portion of cogs even with external surface of drive belt Drive and Driven Pulleys Drive and Driven Pulleys Inspection This inspection must be performed by an authorized Can-Am dealer, repair shop, or person of your own choosing for maintenance, repair, or replace- vmo2012-012-031_a ment.
  • Page 128: Fuses

    MAINTENANCE PROCEDURES Remove corrosion from battery cable terminals and battery posts using a firm wire brush. Battery Installation Battery installation is the reverse of the removal procedure. NOTICE Always connect RED (+) battery cable first. Fuses vmo2012-014-011_a 1. Front fuse box 2.
  • Page 129 MAINTENANCE PROCEDURES Front Fuse Box Description FRONT FUSE BOX All models except 850, 1000R DESCRIPTION RATING and NRMM models 10 A FRONT FUSE BOX Clock DESCRIPTION RATING Lights 30 A Fan Relay Accessories 1 20 A Main Relay Accessories 2 20 A Accessories Relay Injectors...
  • Page 130: Lights

    MAINTENANCE PROCEDURES Rear Fuse Identification FUSE LINK IDENTIFICATION Main 16 awg Fusible links Fan/accessories 16 awg FUSE IN FUSE BOX 2 219002093-006 IDENTIFICATION FUSE BOX 2 Fuse 40 A (dynamic power FUSE HOLDER steering) DESCRIPTION Rating DPS (Dynamic Power Steering) 40 A Lights Main...
  • Page 131: Drive Shaft Boot And Protector

    MAINTENANCE PROCEDURES vmo2012-012-061_a Disconnect the light bulb connector. Rotate light bulb counterclockwise to vmo2012-014-057_a remove it from taillight. Pull out bulb. Properly reinstall removed parts in the reverse order of their removal. Validate headlights operation. Headlight Beam Aiming Turn adjustment screws to adjust beam height to your convenience.
  • Page 132: Wheel Bearing

    Lift and support vehicle. Secure vehicle on jack stands. Push and pull the wheels from the up- per edge to feel the play. See an authorized Can-Am dealer if there is an abnormal play. 219001737-001_a TYPICAL - FINAL TIGHTENING SEQUENCE 2.
  • Page 133: Wheels And Tires

    A. Gap between tire and ring operation. TIRE If the gap is not acceptable, see Tire Replacement REPLACEMENT Tires replacement should be per- formed by an authorized Can-Am Wheels and Tires dealer. Tire Pressure WARNING WARNING – Replace tires only with the same type and size as original tires.
  • Page 134 MAINTENANCE PROCEDURES Tire Mounting on Beadlock Wheels 3. Tighten beadlock screws as per fol- (If equipped) lowing specification and sequence. 1. Mount the tire on wheel. NOTE: To ensure even pressure on the beadlock clamp ring, tighten 1.1 On the opposite side of bead- screws a few turns at a time.
  • Page 135 MAINTENANCE PROCEDURES NOTE: The beadlock clamp ring can flex slightly to match the tire bead. IT IS NORMAL. 6. Verify the gap between tire and beadlock clamp ring, it should be practically equal all around the ring. tbl2011-001-068_a TYPICAL - FINAL TIGHTENING SEQUENCE 219001737-004_a 1.
  • Page 136: Steering

    Push and pull the wheels from the front Suspension Inspection or rear edge to feel the play. Shock Absorbers See an authorized Can-Am dealer if there is an abnormal play or the boot is Inspect shock absorber for oil leaks or cracked.
  • Page 137: Brakes

    Rear Trailing Arms voir. Check trailing arms for distortion, cracks or bending. See an authorized Can-Am dealer if any problem is detected. Brakes Brake Fluid Reservoir Level Verification With vehicle on a level surface, check brake fluid in reservoirs for proper level.
  • Page 138 Wait for the brakes to cool down. The brake inspection, maintenance and repair should be performed by an authorized Can-Am dealer. However, verify the following between visits to your dealer: vmo2012-014-012_a – Brake fluid level 1.
  • Page 139: Vehicle Care

    VEHICLE CARE Post-Operation Care Non Compatible Cleaning Products When vehicle is used in salt-water en- NON-COMPATIBLE MATERIAL vironment (beach area, launching and CLEANING TYPE loading boats etc.), rinsing the vehi- PRODUCTS cle with fresh water is necessary to preserve vehicle and its components. ANY PETROLEUM Metallic parts lubrication is highly rec- BASE CLEANING...
  • Page 140 VEHICLE CARE Compatible Cleaning Products MATERIAL COMPATIBLE TYPE CLEANING PRODUCT XPS ATV WASH Polypropylene (P/N 219 701 702) (body parts) Soapy water vbs2012-006-001 SAFE FOR POLYPROPYLENE ______________...
  • Page 141: Storage And Preseason Preparation

    (4) months, proper storage is a necessity. When using your vehicle after storage, a preparation is required. See an authorized Can-Am dealer, re- pair shop or person of your own choos- ing to have your vehicle prepared for either storage or the preseason.
  • Page 142 STORAGE AND PRESEASON PREPARATION This page is intentionally blank ______________...
  • Page 143: Technical Information

    TECHNICAL INFORMATION ______________...
  • Page 144: Vehicle Identification

    These numbers are also required by the authorized Can-Am dealer to complete warranty claims properly. We strongly recommend that you take note of all the serial numbers on your vehicle and supply them to your insur- ance company.
  • Page 145: Radio Frequency Digitally Encoded Security System (Rf D.e.s.s. Key)

    VEHICLE IDENTIFICATION Radio Frequency Digitally Encoded Security System (RF D.E.S.S. key) This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any in- terference, including interference that 219002021-003...
  • Page 146: Noise Emission Control System Regulation

    NOISE EMISSION CONTROL SYSTEM REGULATION (CANADA/UNITED STATES) Tampering with Noise Control Sys- tem Is Prohibited! U.S. Federal law and Canadian provin- cial laws may prohibit the following acts or the causing there of: 1. The removal or rendering inoper- ative by any person other than for purposes of maintenance, repair or replacement of any device or ele- ment of design incorporated into...
  • Page 147: Canada/United States)

    NOISE EMISSION AND VIBRATION VALUES (ALL COUNTRIES EXCEPT CANADA/UNITED STATES) NOISE EMISSION AND VIBRATION VALUES 82 dB(A) @ 4000 RPM (Uncertainty ) 3dB(A)) Sound pressure 78 dB(A) @ 3600 RPM (Uncertainty ) 3 dB(A)) 84 dB(A) @ 3500 RPM (Uncertainty Noise 1000R ) 3dB(A))
  • Page 148: Ec-Declaration Of Conformity

    EC-DECLARATION OF CONFORMITY DoC_ATV_MY21-EN 15997 ______________...
  • Page 149: Eac Declaration Of Conformity

    EAC DECLARATION OF CONFORMITY Left blank for Eurasian Conformity mark where applicable ______________...
  • Page 150: Specifications

    SPECIFICATIONS ENGINE ROTAX ® 570, 4-stroke, 2 cylinders (V-twin), liquid cooled ROTAX ® 650, 4-stroke, 2 cylinders (V-twin), liquid cooled Engine type ROTAX 850, 4-stroke, 2 cylinders ® (V-twin), liquid cooled ROTAX ® , 1000R, 4-stroke, 2 1000R cylinders (V-twin), liquid cooled 4 valves/cylinder (mechanical adjustment), single over Valve train...
  • Page 151 SPECIFICATIONS LUBRICATION SYSTEM Capacity (oil change with 2.0 L (2.1 qt (U.S. liq.)) filter) 4T 10W50 SYNTHETIC OIL (EUR) (P/N 779240) 4T 5W40 SYNTHETIC Recommended oil BLEND OIL (EUR) (P/N 779290) Scandinavia 4T 0W40 SYNTHETIC OIL (EUR) (P/N 779286) 4T 10W50 SYNTHETIC Engine oil OIL (P/N 779234) 4T 5W40 SYNTHETIC...
  • Page 152 SPECIFICATIONS GEARBOX Dual range (HI-LO) with park, Type neutral and reverse Capacity 450 ml (15.22 U.S. oz) 75W140 Scandinavia: SYNTHETIC GEAR OIL (EUR) (P/N 779215) Gearbox oil All other countries: Recommended 75W140 SYNTHETIC GEAR OIL (P/N 779160) or a 75W140 API GL-5 synthetic gear oil ELECTRICAL SYSTEM Without DPS...
  • Page 153 SPECIFICATIONS FUEL SYSTEM Electronic Fuel Injection (EFI), 46 570/650 mm throttle body, 1 injector per cylinder Fuel delivery Type Electronic Fuel Injection (EFI), 54 850/1000R mm throttle body, 1 injector per cylinder Fuel pump Type Electrical (in fuel tank) Idle speed 1400 rpm (not adjustable) Regular unleaded gasoline Type...
  • Page 154 SPECIFICATIONS DRIVE SYSTEM Capacity 250 ml (8.45 U.S. oz) 75W140 Scandinavia: SYNTHETIC GEAR OIL (EUR) (P/N 779215) Rear final drive oil All other countries: Type 75W140 SYNTHETIC GEAR OIL (P/N 779160) or synthetic gear oil 75W140 API GL-5 CV JOINT GREASE (P/N 293 CV joint grease 550 062) or an equivalent...
  • Page 155 SPECIFICATIONS REAR SUSPENSION Renegade X Fox RC2 shock with piggyback xc 650/850/ reservoir, dual speed compression Type 1000R damping adjustment and rebound adjustment. Shock absorber Renegade Base 850 Type FOX HPG Renegade Base Type Motion Control 570/650 5 position cam Preload adjustment type All other models Threaded...
  • Page 156 SPECIFICATIONS WHEELS Renegade Base Cast aluminum Type Renegade X xc Aluminum with beadlocks Front 30,5 x 15,2 cm (12 x 6 in) Rim size Rear 30,5 x 19,1 cm (12 x 7.5 in) 80 N•m ± 5 N•m Wheel nut torque (59 lbf•ft ±...
  • Page 157: Troubleshooting

    TROUBLESHOOTING ______________...
  • Page 158: Troubleshooting Guidelines

    – Check starter relay. 8. Vehicle wakes up when START button is pressed. – Seek service from an authorized Can-Am dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer to the US EPA EMISSION-RELATED WARRANTY contained herein for informa- tion about warranty claims.
  • Page 159 4. Multifunction gauge CHECK ENGINE indicator lamp is on and display shows CHECK ENGINE. – Seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or replacement. Please refer to the US EPA EMISSION-RELATED WARRANTY contained herein for informa- tion about warranty claims.
  • Page 160 3. Cooling fan inoperative. – Check cooling fan fuse or relay, refer to FUSES in MAINTENANCE PROCE- DURES. If the fuse is good, seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or re- placement.
  • Page 161 ENGINE BACKFIRE (cont’d) 3. Ignition timing is incorrect or there is an ignition system failure. – Seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or replacement. Please refer to the US EPA EMISSION-RELATED WARRANTY contained herein for informa- tion about warranty claims.
  • Page 162 – Once the load is reduced, the normal steering assistance will return. 2. CHECK ENGINE INDICATOR LAMP is ON and display shows CHECK DPS – Seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or replacement.
  • Page 163: Multifunction Gauge Messages

    If the message and the check engine light stay on after engine starting, stop engine. Check engine oil level. Refill if necessary. If the oil level is good, seek service from an authorized Can-Am dealer, repair shop or person of your own choosing for maintenance, repair or replacement.
  • Page 164 MULTIFUNCTION GAUGE MESSAGES This page is intentionally blank ______________...
  • Page 165 WARRANTY ______________...
  • Page 166: Brp Limited Warranty Usa And Canada: 2021 Can-Am Atv

    SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. ("BRP")* warrants its 2021 Can-Am ATV sold by authorized Can-Am ATV dealers (as hereinafter defined) in the United States of America ("USA") and in Canada from defects in material or workmanship for the period and under the conditions described below.
  • Page 167 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2021 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am ATV dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred (“Can-Am ATV dealer”);...
  • Page 168 BRP’s obligations under this warranty are limited to, at its sole discretion, repairing parts found defective under normal use, maintenance and service, or replacing such parts with new genuine Can-Am ATV parts without charge for parts and labor, at any authorized BRP dealer during the warranty coverage period under the conditions described herein.
  • Page 169: Epa Emission-Related Warranty

    BRP. For all emission-related warranty claims, BRP is limiting the diagnosis and repair of emission-related parts to the authorized Can-Am dealers, unless for emergency re- pairs as required by item 2 of the following list.
  • Page 170 Components Covered The emission-related warranty covers all components whose failure would in- crease an engine’s emissions of any regulated pollutant, including the following listed components: 1. For exhaust emissions, emission-related components include any engine parts related to the following systems: –...
  • Page 171 Limited Applicability As a certifying manufacturer, BRP may deny emission-related warranty claims for failures that have been caused by the owner’s or operator’s improper main- tenance or use, by accidents for which the manufacturer has no responsibility, or by acts of God. For example, an emission-related warranty claim need not be honored for failures that have been directly caused by the operator’s abuse of the engine/equipment or the operator’s use of the engine/equipment in a manner for which it was not designed and are not attributable to the manufacturer in any way.
  • Page 172: Brp International Limited Warranty: 2021 Can-Am Atv

    1) SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. ("BRP")* warrants its 2021 Can-Am ATV sold by Can-Am ATV distributors or dealers authorized by BRP to distribute Can-Am ATVs ("Can-Am ATV Distributor/Dealer") outside of the United States of America ("USA"), Canada, member states of the European Economic Area (which is comprised of the states of the European Union plus the United King- dom, Norway, Iceland and Liechtenstein) ("EEA"), Turkey, member states of the...
  • Page 173 Can-Am ATV Distributor/Dealer; – Damage caused by abuse, abnormal use, neglect, racing or operation of the product in a manner inconsistent with the recommended operation described in the Operator’s Guide;...
  • Page 174 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2021 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am ATV Distributor/Dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred;...
  • Page 175 9) CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the Can-Am ATV Distribu- tor/Dealer level. We recommend discussing the issue with the authorized Can-Am ATV Distributor/Dealer's service manager or owner.
  • Page 176: Brp Limited Warranty For The European Economic Area, The Commonwealth Of The Independent States And Turkey Economic Area: 2021 Can-Am Atv

    1) SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Products Inc. ("BRP")* warrants its 2021 Can-Am ATVs sold by distributors or dealers authorized by BRP to distribute Can-Am ATVs ("Can-Am ATV Distributor/Dealer") in member states of the European Economic Area (which is comprised of the member states of the European Union plus the United Kingdom, Norway, Iceland and Liechtenstein) ("EEA"), in member...
  • Page 177 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2021 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am ATV Distributor/Dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred;...
  • Page 178 BRP's responsibility is limited to making the required repairs or replace- ments of parts. No claim of breach of warranty shall be cause for cancellation or rescission of the sale of the Can-Am ATV to the owner. You may have other legal rights which may vary from country to country.
  • Page 179 9) CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the Can-Am ATV Distribu- tor/Dealer level. We recommend discussing the issue with the authorized Can-Am ATV Distributor/Dealer's service manager or owner.
  • Page 180 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be re- sponsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.
  • Page 181: Maintenance Records

    MAINTENANCE RECORDS Send photocopy of maintenance record to BRP if needed. PREDELIVERY Serial number: Signature/Print: Mileage / km: Hours: Date: Dealer no: Notes: Refer to vehicle Pre-Delivery Bulletin for detailed installation procedures FIRST INSPECTION Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide...
  • Page 182 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 183 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide ______________...
  • Page 184 This page is intentionally blank ______________...
  • Page 185: Customer Information

    CUSTOMER INFORMATION ______________...
  • Page 186: Privacy Information

    PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.
  • Page 187: Contact Us

    CONTACT US North America www.brp.com 565 de la Montagne Street Asia Valcourt (Québec) J0E 2L0 Canada Room 4609, Tower 2, Grand Gateway 3 Hong Qiao Sa De Cv, Av. Ferrocarril 202 Road Shanghai, Parque Ind. Querétaro, Lote2-B China 200020 76220 Santa Rosa Jáuregui, Qro., Mexico 21F Shinagawa East One Tower 2-16-1 Konan, Minatoku-ku,...
  • Page 188: Change Of Address/Ownership

    STOLEN UNITS: If your personal ATV is stolen, you should notify BRP or an autho- rized Can-Am dealer. We will ask you to provide your name, address, phone num- ber, the vehicle identification number and the date it was stolen.
  • Page 189 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 190 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 191 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 192 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 193 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 194 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 195 ATV MODEL No. VEHICLE IDENTIFICATION NUMBER (V.I.N.) ENGINE IDENTIFICATION NUMBER (E.I.N.) Owner: NAME STREET CITY STATE/PROVINCE ZIP/POSTAL CODE Purchase Date YEAR MONTH Warranty Expiry Date YEAR MONTH To be completed by the dealer at the time of the sale. DEALER IMPRINT AREA V00A2IL Please verify with your dealer to ensure your vehicle has been registered with BRP.
  • Page 196 RY A PASSENGER. You increase your risk of losing control if you carry a passenger. 219 002 095 OPERATOR’S GUIDE RENEGADE Series / ENGLISH GUIDE DU CONDUCTEUR Séries RENEGADE / ANGLAIS FAIT AU / MADE IN CANADA ®TM AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES.

This manual is also suitable for:

Renegade x mr 2021

Table of Contents