Table of Contents
Advertisement
Distributor of Digi International: Excellent Integrated System Limited
Datasheet of 101-0533 - KIT DEV RABBIT3000/RCM3100
Contact us: sales@integrated-circuit.com Website: www.integrated-circuit.com
2.2 Hardware Connections
2.2.1 Attach Module to Prototyping Board
Turn the RCM3100 module so that the mounting holes on the RCM3100 and on the Proto-
typing Board line up, as shown in Figure 1 below. Align the pins from headers J1 and J2 on
the bottom side of the module into header sockets RCM2JA and RCM2JB on the Prototyping
Board (these sockets were labeled J12 and J13 on earlier versions of the Prototyping Board).
Line up mounting
holes.
Figure 1. Installing the RCM3100 Module on the Prototyping Board
Although you can install a single module into either the
on the Prototyping Board, all the Prototyping Board features (switches, LEDs, serial port
drivers, etc.) are connected to the
position.
MASTER
NOTE: It is important that you line up the pins on headers J1 and J2 of the RCM3100
module exactly with the corresponding pins of header sockets RCM2JA and RCM2JB
on the Prototyping Board. The header pins may become bent or damaged if the pin
alignment is offset, and the module will not work. Permanent electrical damage to the
module may also result if a misaligned module is powered up.
Press the module's pins firmly into the Prototyping Board header sockets—press down in
the area above the header pins using your thumbs or fingers over the connectors as shown
in Figure 1. Do not press down on the middle of the RCM3100 module to avoid flexing
the module, which could damage the module or the components on the module.
Should you need to remove the RCM3100 module, grasp it with your fingers along the sides
by the connectors and gently work the module up to pull the pins away from the sockets
where they are installed. Do not remove the module by grasping it at the top and bottom.
6
RN1
PD1
GND
NC
PD0
RCM1JA
GND
RCM1JB
GND
+3.3V
PD7
PD6
VBAT
RCM3000 ETHERNET CORE MODULE
VRAM
PD3
PD2
EXT
/RES
SM1
PD5
PD4
IN
SM0
/IORD
PG3
PG2
/IOWR
PG4
PG1
PG0
PG5
PG6
PD4
PD5
PG7
PE0
PC5
PC4
PE1
PE3
PC3
PC2
PC1
PE4
PE5
PC0
PE6
PE7
PF0
PF1
PF7
PF6
PF2
PF3
PF5
PF4
PA0
PA1
PB7
PB6
PA2
PA3
PB5
PB4
PA4
PA5
PB3
PB2
PA6
PA7
SLAVE
PB0
PE4
GND
UX10
/RES
MASTER
J1
J3
C1
UX11
RC15
RCM2
RC24
R1
RC19
R4
RC20
RC23
R3
UX9
C3
R5
R2
RC14
RC17
RC22
RC16
RC13
UX3
RC21
RC12
R21
RC10
RC2
UX2
RC11
GND
NC
PD1
PD0
GND
+3.3V
PD7
PD6
VBAT
VRAM
PD3
PD2
EXT
/RES
SM1
PD5
PD4
IN
SM0
/IORD
PG3
PG2
/IOWR
PG4
PG1
PG0
PG5
PG6
PD4
PD5
RCM2JA
RCM2JB
PG7
PE0
PC5
PC4
PE1
PE3
PC3
PC2
PE4
PE5
PC1
PC0
PE6
PE7
PF0
PF1
U1
PF7
PF6
PF2
PF3
PF5
PF4
PA0
PA1
C5
PB7
PB6
PA2
PA3
C8
RCM2JA
RCM2JB
PB5
PB4
PA4
PA5
C6
RESET
S2
S3
PB3
PB2
PA6
PA7
RxC TxC
PB0
/RES
STATUS
GND
C7
J4
J5
RS-232
TxB RxB
GND
position — install a single module in the
MASTER
RN5
D1
R20
C13
R17
U4
C12
U5
+5V
Battery
+3.3V
BT1
J15
GND
GND
GND
+5V
+3.3V
+3.3V
J8
+3.3V
+3.3V
+5V
+5V
RC6
RC7
C16
DISPLAY BOARD
U6
C9
U3
UX5
R14
RC9
UX7
RCM30/31/32XX SERIES
PROTOTYPING BOARD
PG6
PG7
J10
J7
DS1
DS2
DISPLAY BOARD
or the
MASTER
SLAVE
RabbitCore RCM3100
L1
C17
J11
2.5 MM JACK
D2
GND
+DC
+5V
+3.3V
GND
+5V
UX4
RC25
RC4
RC5
C14
RC27
U3
RC28
RC29
RC26
UX13
DISPLAY BOARD
position
Advertisement
Table of Contents
