Hardware Connections; Attach Module To Prototyping Board - Rabbit RabbitCore RCM3000 User Manual

2.2 Hardware Connections

2.2.1 Attach Module to Prototyping Board

Turn the RCM3000 module so that the Ethernet connector end of the module extends off
the Prototyping Board, as shown in Figure 1 below. Align the pins from headers J1 and J2
on the bottom side of the module into header sockets RCM2JA and RCM2JB on the Proto-
typing Board (these sockets were labeled J12 and J13 on earlier versions of the Prototyping
Board).
RCM3000
Do not press down
here.
Figure 1. Install the RCM3000 Module on the Prototyping Board
Although you can install a single module into either the
on the Prototyping Board, all the Prototyping Board features (switches, LEDs, serial port
drivers, etc.) are connected to the
MASTER position.
NOTE: It is important that you line up the pins on headers J1 and J2 of the RCM3000
module exactly with the corresponding pins of sockets RCM2JA and RCM2JB on the
Prototyping Board. The header pins may become bent or damaged if the pin alignment
is offset, and the module will not work. Permanent electrical damage to the module may
also result if a misaligned module is powered up.
Press the module's pins firmly into the Prototyping Board header sockets—press down in
the area above the header pins using your thumbs or fingers over the connectors as shown
in Figure 1. Do not press down on the middle of the RCM3000 module to avoid flexing
the module, which could damage the module or the components on the module.
Should you need to remove the RCM3000 module, grasp it with your fingers along the sides
by the connectors and gently work the module up to pull the pins away from the sockets
where they are installed. Do not remove the module by grasping it at the top and bottom.
6
RN1
GND NC PD1 PD0
RCM1JA GND RCM1JB
GND +3.3V PD7 PD6
VBAT
RCM3000 ETHERNET CORE MODULE
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0 PF1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4 PA4 PA5
PB3 PB2 PA6 PA7
SLAVE
PB0 /RES PE4 GND UX10
MASTER
J1 J3
C1
UX11
RC15 RCM2
RC24
R1 RC19
R4
RC20
RC23
R3
UX9
C3
R5
R2
RC14
RC22
RC17
RC16
RC13
UX3
RC21
RC12
R21
RC10
RC2
UX2
RC11
GND NC PD1 PD0
GND +3.3V PD7 PD6
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
RCM2JA RCM2JB
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0 PF1
U1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
C5
PB7 PB6 PA2 PA3
C8
RCM2JB
PB5 PB4 PA4 PA5 RCM2JA
C6
RESET
S2
PB3 PB2 PA6 PA7
RxC TxC
PB0 /RES STATUS GND C7
J5
J4
RS-232
TxB RxB GND
MASTER position — install a single module in the
RN5
D1
C13
R20
R17
U4
C12
+5V
Battery
+3.3V
BT1
J15
GND
GND
GND
+3.3V +5V
+3.3V
J8
+3.3V +3.3V
+5V +5V
RC6 RC7
C16
DISPLAY BOARD
U6
C9
U3
UX5
R14
RC9
UX7
RCM30/31/32XX SERIES
PROTOTYPING BOARD
S3
PG7
PG6
J10
DS1 DS2 DISPLAY BOARD
MASTER or the SLAVE
RabbitCore RCM3000
L1
C17
J11
2.5 MM JACK
D2 GND +DC
U5
+5V
+3.3V
GND
+5V
UX4
RC25
RC4
RC5
C14
RC27
U3
RC28
RC29
RC26
UX13
J7
DISPLAY BOARD
position