Table of Contents
Advertisement
Item
[SDI&HDMI SELECT]
[3G-SDI OUT]
[SDI OUT CHAR]
[SDI EDH]
[HD SDI REMOTE]
[DOWNCON MODE]
[DOWNCON SETTING]
[DETAIL]
[H.DTL LEVEL]
[V.DTL LEVEL]
[DTL CORING]
[H.DTL FREQ]
[VIDEO OUT]
[VIDEO OUT CHAR]
[VIDEO OUT ZEBRA]
[TC OUT]
[TC OUTPUT REF]
Chapter 6 Menu Operations — Menu list
Selects output signals from the <SDI OUT> terminal and <HDMI OUT> terminal.
[SYSTEM MODE]: Follows the setting in [SYSTEM MODE] → [LINE&FREQ].
[1080i]: Converts into interlaced signals and outputs them when [1080-59.94P] or [1080-50P] is selected
in [SYSTEM MODE] → [LINE&FREQ]. This cannot be selected when other settings are made.
[DOWNCON]: Down converts to SD signal and outputs.
f Factory setting: [SYSTEM MODE]
Selects 1080P signals of the HD SDI output in 1080P mode.
[LEVEL-A]: Selects the LEVEL-A method.
[LEVEL-B]: Selects the LEVEL-B DL method.
f Factory setting: [LEVEL-B]
Selects whether to superimpose characters on <SDI OUT> terminal output images.
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
Selects whether to superimpose EDH when output from the <SDI OUT> terminal is SD signal (480i and
576i).
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [ON]
Sets whether to use the control function of recording operation for an external device (such as a recorder)
connected to the <SDI OUT> terminal at HD SDI output.
[ON]: Controls the recording operation of the external device.
[OFF]: Does not control the recording operation of the external device.
f Factory setting: [OFF]
Selects the mode of the down converter output signal mode from the <SDI OUT> or <GENLOCK IN/
VIDEO OUT> terminal in HD mode (1080P, 1080i, or 720P).
[SIDE CROP], [LETTER BOX], [SQUEEZE]
f Factory setting: [LETTER BOX]
Turns detail function for the down converter output signal [ON]/[OFF].
[ON], [OFF]
The down converter output signal contains detail components set during HD signal processing.
This setting superimposes the detail components exclusive to down converter output to that signal.
f Factory setting: [ON]
Sets horizontal detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [8]
Sets vertical detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [4]
Sets the detail noise removal level.
[0]...[15]
f Factory setting: [1]
Selects the horizontal detail frequency.
[2.5MHz], [3MHz], [3.5MHz], [4MHz], [4.5MHz]
f Factory setting: [3.5MHz]
Selects the <GENLOCK IN/VIDEO OUT> terminal output [ON]/[OFF].
[ON]: Performs output.
[OFF]: Stops output.
f Factory setting: [OFF]
Selects whether to superimpose characters on <GENLOCK IN/VIDEO OUT> terminal output images.
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [ON]
Selects whether the zebra pattern is superimposed over the output video signals from the<GENLOCK IN/
VIDEO OUT> terminal.
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
Sets the type of time code output from the <TC IN/OUT> terminal.
[TCG]: Outputs the time code generator value of the camera at all times.
[TCG/TCR]: Outputs the time code generator value for camera image output, and the time code value of
the video being played back for video playback output.
f Factory setting: [TCG]
Sets the output delay of time code output from the <TC IN/OUT> terminal.
[RECORDING]: Outputs the recorded time code with no delay. This is used when performing simultaneous
recording on two cameras with the time code of this camera as the master.
[VIDEO OUT]: Matches to output images.
f Factory setting: [VIDEO OUT]
– 132 –
Description of settings
Advertisement
Table of Contents
