Table of Contents
Advertisement
No
Item
<AUTO/MANUAL> switch operation
40
display
41 GPS display
Audio monitor volume adjustment
42
display
43 Front audio level volume display
*1
May be displayed depending on other settings.
*2
Displayed when the remaining capacity becomes smaller.
*3
Displayed during shooting.
Mode check display
The camera settings and status can be displayed on the viewfinder or LCD monitor screen for check.
Each time the <DISP/MODE CHK> switch on the camera is pushed towards the <CHK> side, the five screens are switched.
[STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [META INFO] screen display → no
display
Each screen is displayed for approximately five seconds. Pushing the <DISP/MODE CHK> switch towards the <CHK> side while the screen is displayed
moves to the next screen.
[FUNCTION] screen
Displays the video output status and information of the recording media.
[SDI OUT]
[P2CARD STATUS]
[PROXY]
[NETWORK]
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
[AUDIO]
[A.IN]
[LEVEL]
Chapter 7 Display — Screen status display
Shooting
Playback
—
l
—
l
l
l
—
l
—
Displays the status of the signal output from the <SDI OUT> terminal.
Displays the format of the signal output from the <SDI OUT> terminal by [HD-SDI]/
[TYPE]
[SD-SDI].
Displays the superimposition status of characters selected in the main menu → [OUTPUT
[CHAR]
SEL] → [SDI OUT CHAR] by [ON]/[OFF].
Displays the status of the P2 card inserted in the card slot, remaining capacity, and total
used capacity.
The statuses of cards to be displayed are as follows:
—
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to "P2 card access LEDs and status of P2 cards" (page 34).
Displays the remaining capacity/total capacity totaled for slots 1 and 2 (or slots 3) and the
[TOTAL P2/mP2]
recording media ([P2] or [mP2]).
Displays the status of the microP2 memory card in slot 1 and remaining capacity/total
[SLOT1]
capacity.
Displays the status of the microP2 memory card in slot 2 and remaining capacity/total
[SLOT2]
capacity.
[SLOT3]
Displays the status of the P2 memory card in slot 3 and remaining capacity/total capacity.
Displays the media selection status for proxy recording.
[MEDIA]
[P2]/[P2&SD]/[OFF]
Displays the setting status for proxy recording mode.
[MODE]
[AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]
[PROXY ERROR]
Displays the operation error on the proxy module.
[NETWORK]
Displays the network to be used and its status.
Displays the built-in microphone status set in the main menu → [AUDIO SETUP] → [INPUT
SETTING] → [INT MIC].
f [STEREO]: Records audio from two directions in the front with the 2ch stereo
microphone.
[INT MIC]
f [MONO]: This mode records clearer audio from the front by enhancing the directionality
forward like a shotgun microphone. Audio recorded on the left and right are the same.
f [OFF]: Disables audio of the built-in microphone.
Displays the audio input signal status set in the main menu → [AUDIO SETUP] →
[AUDIO OUT]
[OUTPUT SETTING] → [AUDIO OUT].
[CH1/CH2]/[CH1]/[CH2]/[CH3/CH4]/[CH3]/[CH4]
Displays the input status of each channel.
[CH1/2/3/4]
[INT(L)]/[INT(R)]/[INPUT1]/[INPUT2]
Displays the recording level adjustment method currently selected on each channel.
f [VR]: Displayed when manual adjustment using the adjustment dial is set.
f [MENU]: Displayed when manual adjustment using [LEVEL CONTROL CH3]/[LEVEL
[CH1/2/3/4]
CONTROL CH4] is set in the main menu → [AUDIO SETUP] → [RECORDING CH
SETTING].
f [AUTO]: Displayed when automatic adjustment is set.
– 146 –
<DISP/
<DISP/MODE
MODE CHK>:
CHK>: <OFF>
<CHK>
—
l
—
l
—*
—*
1
1
—*
—*
1
1
<DISP/MODE CHK>: <ON>
[OTHER DISPLAY]
[ALL]
[PARTIAL]
[USER]
l
l
—
l
—*
—*
1
1
—*
—*
1
1
l
l
—*
1
—*
1
Advertisement
Table of Contents
