Table of Contents
Advertisement
Safety
1.1 General considerations
General safety instructions
•
Before operating this equipment please read this manual thoroughly and retain it for future reference.
•
Installation and preliminary adjustments should be performed by qualified Barco personnel or by
authorized Barco service dealers.
•
All warnings on the projector and in the documentation manuals should be adhered to.
•
All instructions for operating and use of this equipment must be followed precisely.
•
All local installation codes should be adhered to.
•
IEC/EN 60825-1: 2014 Laser class 1 RG2 or RG3.
•
IEC/EN 62471-5:2015 RG2 or RG3.
•
Additional instructions to supervise children, no staring, and not use optical aids.
•
Additional instructions to install above the reach of children.
•
Notice is given to supervise children and to never allow them to stare into the projector beam at any
distance from the projector.
•
Notice is given to use caution when using the remote control for starting the projector while in front of the
projection lens.
•
Notice is given to the user to avoid the use of optical aids such as binoculars or telescopes inside the
beam.
•
"As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015".
•
"WARNING: MOUNT ABOVE THE HEADS OF CHILDREN. The use of a ceiling mount is recommended
with this product to place it above the eyes of children.
Notice on safety
This equipment is built in accordance with the requirements of the applicable international safety standards.
These safety standards impose important requirements on the use of safety critical components, materials
and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and
having access to live parts. Safety standards also impose limits to the internal and external temperature rises,
radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of
fire. Simulated single fault condition testing ensures the safety of the equipment to the user even when the
equipment's normal operation fails.
Laser safety precautions for G100 Series
This product is classified as CLASS 1 LASER PRODUCT - RISK GROUP 2 of IEC 60825-1 : 2014 and also
complies with 21 CFR 1040.10 and 1040.11 except for conformance as a Risk Group 2 LIP as defined in IEC
62471-5:Ed. 1.0. For more information, see Laser Notice No. 57, dated May 8, 2019.
When installed with G LENS (2.0 - 4.0 : 1) and G LENS (4.0-7.2 : 1) lens (throw ratio greater than 2.0), this
projector may become Class 1 Laser Product-Risk Group 3 (RG3) according to IEC 60825-1:2014, IEC
62471-5: 2015, and also make a variance approvals under 21 CFR 1010.4 for RG3 LIP according to
Classification and Requirements for Laser Illuminated Projectors (LIPs) (Laser Notice No. 57).
To ensure safety operation, read all laser safety precautions before installing and operating the projector.
•
This projector uses extremely high brightness laser. Do not stare into the direct light beam, as the
extremely high
brightness may cause permanent eye damage. (Risk Group 2 of IEC 62471-5:2015).
•
No direct exposure to the beam shall be permitted. (Risk Group 3 of IEC 62471-5:2015).
•
This product is not for household use.
•
Possibly hazardous optical radiation emitted from this product.
•
This projector has a built-in Class 4 laser module. Never attempt to disassemble or modify the laser
module.
•
Any operation or adjustment not specifically instructed in the User manual creates the risk of hazardous
laser
radiation exposure.
•
Do not stare into beam when the projector is on. When turning on the projector, make sure no one within
projection range is looking into the lens.
•
Follow the control, adjustment, or operation procedures to avoid damage or injury from exposure of laser
radiation.
8
R5913459 /00
G100
Advertisement
Table of Contents
