Beckhoff BK5200 Documentation page 40

Parameterization and Commissioning
LEDs Network Sta-
tus NS
(duo LED)
Products
BK5200 X
BK5210B1
BK5210B2
BK5220
BK5250
LC5200
IP Compact
Box
IP Coupler
Box
LEDs NS
red flashing Time-Out, no
connection to
master, check
cabling
red ON Duplicate MAC
Id fault, check
for same ad-
dress in net-
work
Bus OFF, check
cabling, check
bus termination,
check bus
length
CAN Rx/Tx
Overrun, reduce
IO cycle time for
device at scan-
ner
red OFF No baud rate,
Device is not
able to detect
DeviceNet baud
rate (IO LEDs
ON)
all OFF No baud rate,
Device is not
IO LEDs ON
able to detect
DeviceNet baud
rate (IO LEDs
ON)
all OFF
IO LEDs OFF
40
Module Status Network Sta-
MS tus NS
(duo LED) (duo LED)
X
X
X
X
X
MS NS
K-Bus error, Time-Out, no
check for error connection to
at connected master, check
terminals cabling
Diagnostic of
connected ter-
minal
Duplicate MAC
Id fault, check
for same ad-
dress in net-
work
Bus OFF, check
cabling, check
bus termination,
check bus
length
CAN Rx/Tx CAN Rx/Tx
Overrun, reduce Overrun, reduce
IO cycle time for IO cycle time for
device at scan- device at scan-
ner ner
No error BusSense error
(all OFF, includ-
ing IO LEDs)
No baud rate,
Device is not
able to detect
DeviceNet baud
rate (IO LEDs
ON)
No baud rate, No baud rate,
Device is not Device is not
able to detect able to detect
DeviceNet baud DeviceNet baud
rate (IO LEDs rate (IO LEDs
ON) ON)
BusSense error
(all OFF, includ-
ing IO LEDs)
Version: 2.0.0
Module Status Net/Mod Sta-
MS tus NMS
(duo LED) (duo LED)
X
X
X
X
MS NMS
K-Bus error, Time-Out, no
check for error connection to
at connected master, check
terminals cabling
Diagnostic of K-Bus error,
connected ter- check for error
minal at connected
terminals
CAN Rx/Tx Duplicate MAC
Overrun, reduce Id fault, check
IO cycle time for for same ad-
device at Scan- dress in net-
ner work
Bus OFF, check
cabling, check
bus termination,
check bus
length
CAN Rx/Tx
Overrun, reduce
IO cycle for de-
vice time at
scanner
BusSense error BusSense error
(all OFF) (all OFF, includ-
ing IO LEDs)
No baud rate,
Device is not
able to detect
DeviceNet baud
rate (IO LEDs
ON)
No baud rate, No baud rate,
Device is not Device is not
able to detect able to detect
DeviceNet baud DeviceNet baud
rate (IO LEDs rate (IO LEDs
ON) ON)
BusSense error BusSense error
(all OFF, includ- (all OFF, includ-
ing IO LEDs) ing IO LEDs)
ADR RUN
(LED red) (LED green)
X X
X X
X X
ADR RUN
MAC-ID (Node
Address) is set
by software, dif-
fers from adjust-
ments of DIP
switches
CAN Rx/Tx
Overrun, reduce
IO cycle time for
device at Scan-
ner
MAC Id (Node
address) from
DIP switches is
valid
No baud rate, No baud rate,
Device is not Device is not
able to detect able to detect
DeviceNet baud DeviceNet baud
rate (IO LEDs rate (IO LEDs
ON) ON)
BusSense error BusSense error
(all OFF, includ- (all OFF, includ-
ing IO LEDs) ing IO LEDs)
BK52x0 and LC5200