stayer SC210BW Operating Instructions Manual page 26

9. Changing tools
Attention!
This operation must be carried out with the machine
unplugged and with the disk still. Use protective gloves.
- Use obligatorily disk according to normative EN 847-1
- Use obligatorily disc thicker than the riving knife
- Use obligatorily the regulatory push stick and save it
away if not use it.
- Use of fast steel discks prohibited (HSS)
- Use of defective or deformed prohibited
- Replace the table insert when worn
Removal of the cutting disk
IMAGES A B K L
1.Place the head in its upper blocking position by tilting
the head upwards until abutting.
2.Immobilize flange 23 by means of the flange wrench as
delivered together with the equipment.
3.Loosen hexagon head screw 22 clockwise with the
tubular key as delivered together with the equipment.
4.Tighten button 30 to unblock the movable guard 5.
5.Clear guard 5 by pulling it upwards.
6.Hold the disc with one hand
7.Remove the flange and the hexagon head screw.
8.Remove the disk to be changed.
Only SC2500W
1.Place the head in its upper blocking position by tilting
the head upwards until abutting.
2.Loosen the 5 screws 54 holding the casing 1.
3.Loosen the 2 screws keel 55 of the top 56 top table
4.Immobilize flange 23 by means of the flange wrench as
delivered together with the equipment.
5.Loosen hexagon head screw 22 clockwise with the
tubular key as delivered together with the equipment.
6.Tighten button 30 to unblock the movable guard 5.
7.Clear guard 5 by pulling it upwards.
8.Hold the disc with one hand
9.Remove the flange and the hexagon head screw.
10.Remove the disk to be changed.
Changing the cutting disk
1.Carefully clean sawdust and debris from the supports,
flanges and the insides of the guards.
2.Place the new cutting disk in such a manner that the
direction of the arrow of the front side of the casing 1
coincides with the arrow engraved in the disk and with the
direction of the disk teeth as such.
3.Place the flange and the hexagon head screw 22.
4.Block flange 23 with the flange wrench as delivered
together with the equipment.
5.Tighten screw 22 counter clockwise by means of the
tubular key as delivered together with the equipment.
6.Place guard 5 in its original protective position.
7.Revise the operation by carrying out a cutting operation
with no load.
ENGLISH
26
10. Fixing for operation
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene.
During the cut, keep the workpiece fixed to the support.
ALL MACHINES ARE PREPARED FOR MOUNTING
CLAMPS ALLOWING FASTENING THE PROFILE IN A
SAFE MANNER.
To avoid deformations of the workpieces during fixing
thereof, the use of wooden profiles being easily applicable
to the movable jaws of the clamps is advised. Clamps can
be easily extracted and leave the working surface totally
clear.
For cutting long workpieces under safe conditions it is
essential to hold them with additional supports.
11. Limits regarding the workpiece size
Limits for all models as included in the present manual
12. General instructions for use
Warning!
1. Do NOT use the machine if it is in a bad condition or
lacks parts including the prescribed upper guards (the
illustrations of the present manual may be used as an
orientative guide). Unplug it, remove it from the working
area and immediately send it to an authorized technical
service.
2.Know and comply with all safety measures before you
start the machine.
3. Obligatory used of aspiration particle system when
cutting the wood.
Starting and stopping the machine
IMAGES A B N
Information
1.The machine is provided with a locking button 3 for
starting allowing the motor to run without needing to push
switch 2 permanently.
2.The equipment is provided with a safety module
protecting it against unexpected starts. If, whilst the
machine is running, the supply of electrical power should
cease, the machine will not start after reestablishment
thereof. To release the protection push the starting button
2 twice.
3.All models are single speed.
Warnings!
1.Avoid locking whenever possible (button 3).
2.Never leave running machine unattended.
3.Never start the machine with locked disk and, before
starting a cut, always wait until the cutting disk has
reached its maximum speed.
4.Before stopping the machine the disk must be clear and
be rotating freely.
Starting with the manual switch
1.Push switch 2 to actuate the motor.
Stopping the machine when actuated with the manual
switch.
1. Stop pushing switch 2.
26