stayer SC210BW Operating Instructions Manual page 24

29.Locking button for the upper resting position
30.Locking button for the tiltable guard hood
31.Locking button for the lower resting position
32.Counterweight spring for the cutting head
33.Adjustment cam for the indicator for horizontal angles
34.Stationary lower guard
35.Nut for retaining the adjustment of the locking in the
lower position
36.Screw for adjusting the locking in the lower position
37.Keel of the upper table
38.Lock for the guard of the upper table
39.Fastening screw for the adjusting system for fixed-
length cutting
40.Fastening wedge of the adjusting system for fixed-
length cutting
41.Support for the adjusting system for fixed-length cutting
42.Adjustable stopper of the adjusting system for fixed-
length cutting
43.Adjusting wing nut for the movable stopper guide of the
upper table
44.Insertion hollow of the system for fixed-length cutting
45.Cutting length scale of the upper table
46.Keel height adjusting screw
47.Brush-holder lid
48.Fastening screw for the brush-holder cover
49.Brush-holder
50.Brush-holder connecting screw
51.Brush pressing spring
52.Brush
53.Horizontal head movement button.
54.Adjustment screws crankcase.
55.Cover fixing bolts of the keel top table.
56.Cover top table keel.
6. Limitations regarding environmental
conditions
The IP degree of this machine is 20. This machine is
protected against its dangerous parts being accessed by a
finger and against solid foreign particles having diameters
of 12'5 mm and more.
This machine does not have any kind of protection against
the entry of water so that its use in exterior or interior
environmental conditions with a risk of precipitations is
forbidden.
7. List of contents
1.Provided uses of the machine
2.Unpackaging and assembling
3.Setting or fastening the machine in a stable position
4.Connection to the grid, wiring, fuses, socket type for the
jack and grounding conditions
5.Illustrated descriptions of functions
6.Limitations regarding environmental conditions
7.List of contents
8.Settings and testing
9.Changing tools
10.Fixing for operation
11.Limits regarding the workpiece size
12.General instructions for use
13.Precautions and working garment
14.Special safety precautions
ENGLISH
24
15.Measures for preventing machine-specific risks
16.Dust extraction
17.General safety instructions
18.Regular cleaning, maintenance and greasing
19.Repair service by the manufacturer or commercial agent
20.List of parts that may be replaced by the user
21.Special tools as possibly required
22.Safe operation
23.Technical specifications
24.Warrantee
25.Declaration of conformity
8. Settings and testing
Warning!
Before any intervention on the electrical tool remove jack
from power socket.
If the machine has been subject to prolonged or intense
use, it must be checked and adjusted so as to ensure the
machine's correct quality of service and safety.
This requires knowledge, experience and special tools.
The official technical service of Stayer Iberica S.A.
will carry out that work for you in a quick thorough and
inexpensive manner.
Adjusting the locking in the lower resting position
IMAGES A C
Checking
1.On starts from the machine being locked in the upper
resting position.
2.Unlock by pressing button 29.
3.Lower down to the lower stop by means of
4.Press button 31. If the bolt of the button is well adjusted,
it must enter until abutting. Otherwise proceed to adjusting.
Adjusting
1.Loosen fastening screw 35.
2.Lower the head down to the lower stop by means of 4.
3.Tighten or loosen screw 36 until button 31 smoothly
penetrates until abutting. Whilst retaining screw 36, fasten
screw 35.
Adjusting the horizontal mitre angle to +- 45º
IMAGES A B R I
Checking
1.Raise locking bolt 14 (SC2500W, Turn the locking knob
14 toward the left and press the button 53 to move the
head).
2.Move the head horizontally until it locks at +45º
(SC2500W/SC2600W Rotate the knob 14 to adjust the
head in the desired position).
3.Check that the indicator for horizontal angles marks
exactly 45º. If not, proceed to adjusting.
4.Repeat the same sequence for the horizontal angle at -45º.
Adjusting
1.Keep locking bolt 14 raised .
2.Loosen fastening screw of cam 33.
24