stayer SC210BW Operating Instructions Manual page 25

3.Move the whole of head and cutting table horizontally
until it locks at 45º.
4.Turn cam 33 against guide 13 until indicator 9 coincides
with the 45º marking of indicator 7.
5.Tighten the fastening screw of cam 33.
6.Release locking bolt 14.
7.Repeat the same sequence for the horizontal angle at 45º.
Adjustment for SC2500W / SC2600W
1.Turn the locking knob 14 to the left, and click the button
53 to move the head.
2.Horizontally move the head assembly and cutting table
up to 45 degrees.
3.Release the button 53 of the locking knob 14 and turn
right to secure.
4.Repeat the same sequence for the horizontal angle of
-45 degrees.
Adjusting the vertical mitre angle to 90º
IMAGES A B G
Checking
1.Release vertical adjustment of the head by loosening
control element or nut 15 (with Allen key).
2.Move head to the right stopper (90º).
3.Lock the vertical adjustment of the head by tightening
control element or nut 15 (with Allen key).
4.Check the angle by means of a duly calibrated angle
chart or a goniometer (minimum precision +- 5º) applying
one of the surfaces thereof on cutting table 6 and the other
on cutting disk 21.
5.Should the side of the angle chart not adjust exactly to
the disk or if the direct measurement of the goniometer
reached a deviation of more than +- 20º, proceed to
adjusting.
Adjusting
1.Release the vertical adjustment of the head by loosening
control element or nut 15 (with Allen key).
2.Move the head to the right stop (90º).
3.Remove retainer nut 18.
4.Place a goniometer (minimum precision +- 5º) applying
one of its sides on cutting table 6 and the other on cutting
disk 21.
5.Act on adjusting screw 19 until obtaining a measurement
of 90º.
6.Fasten the adjustment by tightening retainer nut 18
whilst retaining screw 19 with a screwdriver so as to
prevent it from moving.
7.Block the vertical adjustment of the head by tightening
control element or nut 15 (with Allen key).
Adjusting the vertical mitre angle to 45º
IMAGES A E
Checking
1.Release the vertical adjustment of the head by loosening
control element or nut 15 (with Allen key)
2.Move head to the left stop (45º).
3.Block the vertical adjustment of the head by tightening
the control element or nut 15 (with Allen key).
ENGLISH
25
4.Check the vertical adjustment by means of a duly
calibrated angle chart or a goniometer (minimum precision
+- 5º) applying one of its sides on cutting table 6 and the
other on cutting disk 21.
5.Should the side of the angle chart not adjust exactly to
the disk or if the direct measurement of the goniometer
reached a deviation of more than +- 20º, proceed to
adjusting.
Adjusting
1.Release the vertical adjustment of the head by loosening
control element or nut 15 (with Allen key).
2.Move head to the left stopper (45º).
3.Remove retainer screw 17.
4.Check the vertical adjustment by means of a duly
calibrated angle chart or a goniometer (minimum precision
+- 5º) applying one of its sides on cutting table 6 and the
other on cutting disk 21.
5. Act on adjusting screw 16 until obtaining a measurement
of 45º on the goniometer or until the surface of the angle
chart that contacts the disk has full (it does not allow any
light to pass through) contact.
6.Fasten the adjustment by tightening retainer screw
17 whilst retaining screw 16 with a screwdriver so as to
prevent it from moving.
7.Block the vertical adjustment of the head by tightening
control element or nut 15 (with Allen key).
Adjusting the keel of the upper cutting table
IMAGES A J I P
Information!
1.You will need a slide gauge and a ruler (not included) to
carry out this adjustment.
Checking
1.Remove the locking element 38 of the guard 26 of the
upper table.
2.Tilt guard 26 backwards.
3.The distance between the inside of keel 37 and the
outside of the teeth of the disk must be between 3mm
and 5mm at any visible point. If the measurements are not
within the range of the figure, proceed to adjusting.
4. The keel 37 must be perfectly aligned with the disc 21. If
not do not use the machine and take it to service.
Adjusting
1.Remove the locking element 38 of the guard 26 of the
upper table.
2.Tilt guard 26 backwards.
3.Loosen the adjusting screws 46 of the keel.
4.Adjust the height of the keel in such a manner that the
distance between the inside of keel 37 and the outside of
the teeth of the disk must be between 3mm and 5mm at
any visible point.
5.Tighten adjustment screws 46 of the keel.
6.Place the guard in its position.
25