Idea 32 Hiline - 42 Hiline; After Use; Vacuum Machine Cleaning; External Cleaning - Orved IDEA 30 User And Maintenance Manual

9.6.2 IDEA 32 HiLine – 42 HiLine
CAUTION!
When the maximum number of set vacuum cycles is reached, the icon
message appear every time the appliance is switched on.
ICON OR
PICTOGRAM
Cool the product: the alarm appears when the set vacuum level cannot be
reached, due to the too high temperature of the product to be packed
Operate the pump dehumidification cycle H2OUT: The alarm appears, when the
machine detects a decrease of efficiency, due to the humidity absorbed by the
pump.
Gas failure: the alarm appears when the machine detects anomalies in inert GAS
inlet system.
Change the oil: the alarm appears when the 5.000 vacuum cycles have been
operated.
In case of pump overheating, all functions stop automatically and the alarm message
appears.
WARNING!
If a thermal safety alarm is triggered, switch the machine off and wait for about 15 minutes until
it cools down. If the alarm persists once the machine is switched on again, switch the machine
off and disconnect it from the mains. Contact your authorised service centre.

10 AFTER USE

 Switch the machine Off:
- pressing for 5" (Models IDEA 30-40 – IDEA 31-41)
- pressing and once again to Switch Off (Models IDEA32 Hi-Line – IDEA42 Hi-Line)
 Clean and dry the packaging machine and the accessories used.
 When the vacuum chamber is completely dry, release the piston (pushing it backwards) and lower the
lid in the rest position, in order to protect the vacuum chamber from dirt and dust.

11 VACUUM MACHINE CLEANING

 Switch the machine Off:
- pressing for 5" (Models IDEA 30-40 – IDEA 31-41)
- pressing and once again to Switch Off (Models IDEA32 Hi-Line – IDEA42 Hi-Line).
 Remove the plug from the socket before each intervention.
 Do not use stainless steel sponges, scrapers, abrasive, acid or aggressive materials which may irreversibly
damage the surfaces, to clean the machine.
 Use a soft cloth and a mild detergent.
 Water and/or steam, could reach live parts and cause short circuit
ELECTRICAL HAZARD!
Never use running water or steam cleaning equipment: Electric shock hazard!
_______________________________________________________________________________________
ORVED S.P.A Rev.01 – 09/2019 – cod. 1500735-00EN – User Manual for
and the oil change
DESCRITPION
IDEA vacuum packing machines Pag. 52 a 76
 Cleaning and routine maintenance, due to the user, cannot be performed by children without supervision.
11.1

EXTERNAL CLEANING

 For steel parts it is advisable to clean by following the direction of the satin finish.
 For the lid and front control panel, use a soft, clean and damp cloth.
 Do not use any solvent, alcohol, corrosive or poisonous liquids.
WARNING!
Do not remove the serial number plates during cleaning.
These provide important information regarding the appliance for any technical support.
WARNING! Do not use water jets or vapour to rinse or clean the machine; avoid using water jets
and vapour near the appliance. Do not spray water on the vacuum chamber suction point.

11.2 VACUUM CHAMBER CLEANING

1) Wait until the sealing bar has cooled down completely.
2) Remove the sealing bar by pulling it up.
3) Avoid cleaning the suction point with water. Water could damage the vacuum packing machine, if
sucked up.
4) Clean with a soft cloth moistened with warm water. Use a mild disinfectant if necessary.
5) Dry thoroughly using a soft cloth.

11.3 SEALING BAR CLEANING

1) Wait until the sealing bar has cooled down completely.
2) Remove the sealing bar by pulling it up.
3) Clean with a soft cloth moistened with warm water.
4) Dry thoroughly using a soft cloth before using the vacuum packing machine.

11.4 External vacuum accessory cleaning

1) Use hot water and dish detergent.
2) Rinse thoroughly.
3) Dry with a clean cloth.
4) Pay attention to reuse the accessory once it has completely dried.

12 oil pump dehumidification cycle (H2OUT)

The vacuum pump is the heart of the machine. It is necessary to follow some simple recommendation, to
prevent pump from internal surfaces oxidation and subsequent blockage of rotor. This is caused by the
presence of oxidized residues, deriving from condensation of water vapour – sucked together with the air-
and remaining into the pump for long:
1) Always pack the product cold, possibly at 3-4°C. The hotter the product, the shorter the foodstuff shelf-life
(due to the bacteria proliferation) and the more condensation forms inside the pump, causing oxidation
and severe damages.
2) If the machine is used only occasionally, please perform at least 2-3 complete USER CYCLES (VAC 99%
AND VAC+ 60") before packaging the products. This allows to pre-heat the oil and the evacuate the water
in the pump.
3) If the vacuum machine is used in catering or restaurant sector, the pump dehumidification cycle must be
performed daily, at the end of working day. In other cases, it must be performed at least weekly.
4) An oil change, has to be scheduled before a long stop or a period of inactivity longer than 2 moths.
_______________________________________________________________________________________
ORVED S.P.A Rev.01 – 09/2019 – cod. 1500735-00EN – User Manual for IDEA vacuum packing machines Pag. 53 a 76