1. Manuals
  2. Brands
  3. Avaya Manuals
  4. Switch
  5. 8800 Series
  6. Installation manual

Avaya 8800 Series Installation Manual

Ethernet routing switch hardware components
Hide thumbs Also See for 8800 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation — SFP, SFP+, XFP, and OADM
Hardware Components
Avaya Ethernet Routing Switch 8800/8600
Release 7.2.10
NN46205-320
Issue 07.02
August 2013

Advertisement

Table of Contents
loading

Related Manuals for Avaya 8800 Series

Summary of Contents for Avaya 8800 Series

  • Page 1 Installation — SFP, SFP+, XFP, and OADM Hardware Components Avaya Ethernet Routing Switch 8800/8600 Release 7.2.10 NN46205-320 Issue 07.02 August 2013...
  • Page 2 Product provided by Avaya including the selection, arrangement and to users of its products. Documentation does not include marketing design of the content is owned either by Avaya or its licensors and is materials. Avaya shall not be responsible for any modifications,...
  • Page 3 See the Avaya Support website: http://support.avaya.com for product notices and articles, or to report a problem with your Avaya product. For a list of support telephone numbers and contact addresses, go to the Avaya Support website: http://support.avaya.com, scroll to the bottom of the page, and select Contact Avaya Support.
  • Page 4 Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 5: Table Of Contents

    Chapter 2: Introduction...................... Purpose of this document......................... 21 Related resources............................. 21 Documentation..........................21 Training............................21 Avaya Mentor videos........................22 Support..............................22 Chapter 3: New in this release................... Chapter 4: Safety and equipment care information............Handling, safety, and environmental guidelines..................25 Electrostatic Discharge prevention....................
  • Page 6 1000BASE-T SFP specifications....................... 64 1000BASE-SX (LC) SFP specifications....................64 1000BASE-SX (MT-RJ) SFP specifications....................65 1000BASE-LX SFP specifications......................66 1000BASE-XD CWDM SFP specifications....................67 1000BASE-ZX CWDM SFP specifications....................67 1000BASE-SX DDI SFP specifications..................... 68 1000BASE-LX DDI SFP specifications..................... 69 1000BASE-XD DDI 1310 nm SFP specifications..................69 1000BASE-XD DDI 1550 nm SFP specifications..................

  • Page 7: Chapter 1: Regulatory Information And Safety Precautions

    Read the information in this section to learn about regulatory conformities and compliances. International Regulatory Statements of Conformity This is to certify that the Avaya 8000 Series chassis and components installed within the chassis were evaluated to the international regulatory standards for electromagnetic...
  • Page 8 CE Marking Statement (Europe only) EN 55022 Statements This is to certify that the Avaya 8800/8600 Series chassis and components installed within the chassis are shielded against the generation of radio interference in accordance with the application of Council Directive 2004/108/EC. Conformity is declared by the application of EN 55022 Class A (CISPR 22).
  • Page 9 National Electromagnetic Compliance (EMC) Statements of Compliance EN 300386 Statement The Ethernet Routing Switch 8800/8600 Series chassis complies with the requirements of EN 300386 V1.3.3 for emissions and for immunity for a Class A device intended for use in either Telecommunications centre or locations other than telecommunications centres given the performance criteria as specified by the manufacturer.
  • Page 10 Avaya is not responsible for any modifications to the product made on or for use on the territory of Russia, Belarus and Kazakhstan other than modifications executed and certified by Avaya itself.
  • Page 11 National Electromagnetic Compliance (EMC) Statements of Compliance Chinese EMI and safety warnings Voltage: Risk of injury by electric shock Before working on this equipment, be aware of good safety practices and the hazards involved with electrical circuits. Use only power cords that have a good grounding path. Ensure that the switch is properly grounded before powering on the unit.
  • Page 12 CE Marking Statement (Europe only) EN 60 950 Statement This is to certify that the Avaya 8000 Series chassis and components installed within the chassis are in compliance with the requirements of EN 60 950 in accordance with the Low Voltage Directive.
  • Page 13 Norma Oficial Mexicana (NOM): Exportador: Avaya Inc. 4655 Great America Parkway Santa Clara, CA 95054 USA Importador: Avaya Communication de México, S.A. de C.V. Av. Presidente Masarik 111 Piso 6 Col Chapultepec Morales Deleg. Miguel HIdalgo México D.F. 11570...
  • Page 14 Safety Messages This section describes the different precautionary notices used in this document. This section also contains precautionary notices that you must read for safe operation of the Avaya Ethernet Routing Switch 8800/8600. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 15 Electrostatic alert: PRECAUCIÓN ESD (Descarga electrostática) El aviso de ESD brinda información acerca de cómo evitar una descarga de electricidad estática y el daño posterior a los productos Avaya. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013...
  • Page 16 Schäden an Avaya-Produkten verhindert. Caution: PRECAUCIÓN Los avisos de Precaución brindan información acerca de cómo evitar posibles interrupciones del servicio o el daño a los productos Avaya. Caution: CUIDADO Os avisos de cuidado oferecem informações sobre como evitar possíveis interrupções do serviço ou danos aos produtos da Avaya.
  • Page 17 Avaya products. Warning: AVERTISSEMENT La mention Avertissement fournit des informations sur les moyens de prévenir les risques de blessure lors de la manipulation de produits Avaya. Warning: WARNUNG Warnhinweise bieten Informationen dazu, wie man Personenschäden bei der Arbeit mit Avaya-Produkten verhindert.
  • Page 18 Le indicazioni Pericolo—Alta tensione forniscono informazioni per evitare situazioni o condizioni che potrebbero causare gravi danni alle persone o il decesso a causa dell'alta tensione o di scosse elettriche. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 19 National Environmental Statements of Compliance Danger Notice Danger: Danger notices provide information about how to avoid a situation or condition that can cause serious personal injury or death. Danger: La mention Danger fournit des informations sur les moyens de prévenir une situation ou une condition qui pourrait entraîner un risque de blessure grave ou mortelle.
  • Page 20 RoHS Directive are Lead (including solder used in PCB’s), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Avaya declares compliance with the European Union (EU) RoHS Directive (2002/95/EC). WEEE Directive Compliance Statement This product at end of life is subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore is marked with the symbol shown at the left.

  • Page 21: Chapter 2: Introduction

    Related resources Documentation See the Avaya Ethernet Routing Switch 8800/8600 Documentation Roadmap, NN46205-103, for a list of the documentation for this product. Training Ongoing product training is available. For more information or to register, you can access the website at http://avaya-learning.com/.

  • Page 22: Avaya Mentor Videos

    Introduction Avaya Mentor videos Avaya Mentor is an Avaya-run channel on YouTube that includes technical content on how to install, configure, and troubleshoot Avaya products. Go to http://www.youtube.com/AvayaMentor and perform one of the following actions: • Enter a key word or key words in the Search Channel to search for a specific product or topic.

  • Page 23: Chapter 3: New In This Release

    Chapter 3: New in this release The following section lists new features to Avaya Ethernet Routing Switch 8800/8600 Installation — SFP, SFP+, XFP, and OADM Hardware Components, NN46205-320 for Release 7.2.10. New SFP+ devices for Release 7.2.10 Release 7.2.10 adds support for the following SFP+ devices: •...
  • Page 24 New in this release Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 25: Chapter 4: Safety And Equipment Care Information

    Chapter 4: Safety and equipment care information This section contains important safety and regulatory information. Read this section before you install Small Form Factor Pluggable (SFP), Small Form Factor Pluggable Plus (SFP+) and 10 gigabit SFP (XFP) transceivers. Handling, safety, and environmental guidelines Before you install an SFP, an SFP+ or an XFP read the following handling, safety, and environmental guidelines: •...

  • Page 26: Care Of Fiber Optic Equipment

    If you suspect damage to a fiber optic cable, either due to mishandling or an abnormally high error rate observed in one direction, reverse the cable pairs. If the high error rate appears in the other direction, replace the cable. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 27: Fiber Optic Connector Care

    Care of fiber optic equipment Caution: Risk of equipment damage Do not crush fiber optic cable. If fiber optic cable is in the same tray or duct with large, heavy electrical cables, it can be damaged by the weight of the electrical cable. Fiber optic connector care Before connecting fiber optic connectors to transmission equipment, test equipment, patch panels, or other connectors, ensure fiber optic connectors are clean.

  • Page 28: Cleaning Single Connectors

    1. Remove dust or debris by applying canned air to the cylindrical and end-face surfaces of the connector. 2. Gently wipe the cylindrical and end-face surfaces with a tissue dampened with optical-grade isopropyl alcohol. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 29: Cleaning Duplex Connectors

    Care of fiber optic equipment 3. Gently wipe the cylindrical and end-face surfaces with a dry tissue. Important: Do not let the IPA evaporate; wipe it dry immediately. Alcohols can leave a residue that is difficult to remove. 4. Dry the connector surfaces by applying canned air. 5.

  • Page 30: Cleaning Receptacles

    • You need a high-quality canned compressed air with extension tube. Compressed air must be free of dust, water, and oil, or filmy deposits or scratches on the surface of the connector can result. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 31 Care of fiber optic equipment Caution: Risk of equipment damage To avoid contamination, optical ports must only be cleaned when there is evidence of contamination or reduced performance, or during their initial installation. To prevent oil contamination of connectors, use only high-quality canned compressed air. Do not allow the air extension tube to touch the bottom of the optical port.
  • Page 32 Safety and equipment care information Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 33: Chapter 5: Small Form Factor Pluggable Transceivers

    You can use the Power Management function to monitor the power usage of modules containing SFPs. For more information, see Avaya Ethernet Routing Switch 8800/8600 Administration, NN46205-605. For information about the minimum software versions required to support the hardware described in this document, see Avaya Ethernet Routing Switch 8800/8600 Administration, NN46205-605.
  • Page 34 Job aid SFPs are hot-swappable input and output enhancement components designed for use with Avaya products to allow gigabit Ethernet ports to link with other gigabit Ethernet ports over various media types. The SFPs described in this section do not have Digital Diagnostic Interface capability, and are RoHS -E5 compliant.
  • Page 35 8800/8600 Performance Management, NN46205-704. The SFPs described in this section are all RoHS -E6 compliant. The following tables list and describes the Avaya SFP models with DDI capability. All the optical SFPs use LC connectors. Table 1: 100BASE Small form factor pluggable transceivers...

  • Page 36: Installing An Sfp

    SFP specifications page 61. Installing an SFP Install an SFP to provide an interface between the switch and the network cable. Installing an SFP takes about three minutes. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 37 Installing an SFP Prerequisites • Verify that the SFP is the correct model for your network configuration. • Before you install the optical connector, ensure it is clean. Warning: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port.
  • Page 38 The following figure shows the 1000BASE-SX MT-RJ SFP. Push the tab to release the device. The following figure shows the wrap-around latch-type extraction mechanism. To remove the device, push the collar towards the module. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 39: Removing An Sfp

    Removing an SFP Removing an SFP Remove an SFP to replace it or to commission it elsewhere. Prerequisites • Wear an antistatic wrist strap. Warning: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port.
  • Page 40 5. Store the SFP in a safe place until needed. Important: If you discard the SFP, be sure to dispose of it according to all national laws and regulations. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 41: Chapter 6: Small Form Factor Pluggable Plus Transceivers

    CPU# [date time] COP-SW INFO Slot #: 1G SFP detected in 10G SFP+ port #. Port offline. In addition, the port is prevented from coming online. This is true even if the inserted part is Avaya- qualified. Selecting an SFP+ About this task Use an SFP+ transceiver to interface a device motherboard to a fiber optic cable.

  • Page 42: Job Aid

    SFP+ transceivers are hot-swappable input and output enhancement components that allow 10 gigabit connections. All Avaya SFP+ transceivers use Lucent connectors (LC) to provide precision keying and low interface losses. The following table lists and describes the Avaya SFP+ models.

  • Page 43: Installing An Sfp

    Installing an SFP+ SFP+ order number Description AA1403019-E6 10GBASE-CX 4-pair direct attach twinaxial copper cable to connect 10 Gb ports. The length is 3 m. AA1403020-E6 10GBASE-CX 4-pair direct attach twinaxial copper cable to connect 10 Gb ports. The length is 5 m. AA1403153-E6 10GBASE-ER CWDM SFP+ AA1403154-E6...
  • Page 44 Apply a light pressure to the SFP+ until the device clicks and locks into position in the module. 4. Remove the dust cover from the SFP+ optical bores and insert the fiber optic cable. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 45: Job Aid

    Removing an SFP+ Job aid Depending on the transceiver manufacturer, the SFP+ transceiver uses bail-latch type of locking and extractor mechanism. The following figure shows typical mechanism used on SFP+ transceivers; other locking and extractor mechanisms exist. SFP+ transceivers are similar to SFPs in physical appearance. In the following figure, the SFP+ uses the bore plug.
  • Page 46 5. Store the SFP+ transceiver in a safe place until needed. Important: If you discard the SFP+ transceiver, dispose of it according to all national laws and regulations. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 47: Chapter 7: 10 Gigabit Small Form Factor Pluggable Transceivers

    XFP models. Important: Avaya recommends that you only use Avaya-qualified XFPs. If you do choose to use other vendor XFPs, be aware that Avaya does not support the use of other XFPs.
  • Page 48 Caution: Risk of equipment damage Avaya recommends that you install only one 10GBASE-ZR/ZW XFP for each module due to cooling limitations on the 8683XLR and 8683XZR modules. Avaya further recommends the installation of the XFP only in port 1. You can install a 10GBASE-SR, -LR/LW, or - ER/EW in one or both of the remaining ports.

  • Page 49: Installing An Xfp

    Caution: Risk of equipment damage Avaya recommends that you install only one 10GBASE-ZR/ZW for each module due to cooling limitations on the 8683XLR and 8683XZR modules. Avaya further recommends the installation of the XFP only in port 1. You can install a 10GBASE-SR, -LR/LW, or -ER/EW in one or both of the remaining ports.
  • Page 50 Depending on the transceiver manufacturer, your XFP transceiver can have various types of locking and extractor mechanisms. The following figure shows a typical bail-type mechanism used on XFP transceivers. Pull the bail down to release the device. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 51: Removing An Xfp

    Removing an XFP Removing an XFP Remove an XFP to replace it or to commission it elsewhere. Warning: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port.
  • Page 52 10 Gigabit small form factor pluggable transceivers Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 53: Chapter 8: Optical Multiplexers

    Chapter 8: Optical multiplexers The Avaya optical routing system supports high-speed data communications in Metropolitan Area Networks (MAN) by connecting gigabit Ethernet ports with fiber optic networks, and by combining multiple wavelengths on a single fiber to expand available bandwidth.
  • Page 54 1. Support the chassis so that all of the mounting holes in the optical shelf align with the corresponding holes in the rack. 2. Attach two rack mounting bolts to each side of the rack. 3. Tighten all of the bolts in rotation. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 55: Installing A Multiplexer

    Installing a multiplexer Installing a multiplexer OADMs and OMUXs are passive devices that require no power for their operation. You can insert them in the optical shelf, and then connect them into your network. Procedure steps 1. Align the plug-in module with the optical shelf. 2.
  • Page 56 5. Connect the east backbone fiber optic cable to the OADM east connector. Job aid The Avaya passive CWDM optical add drop multiplexer (OADM) sends and receives signals to and from CWDM SFPs installed in the switch. The OADM adds or drops a specific wavelength from the optical fiber, and allows all other wavelengths to pass through unaffected.

  • Page 57: Connecting An Omux

    Connecting an OMUX Connecting an OMUX Use this procedure to connect the OMUX to an SFP and to east and west backbone interfaces. Prerequisites • Follow proper safety and cleaning procedures. Warning: Risk of personal or equipment damage Multiplexing together several SFPs can produce a radiant power level in the fiber that exceeds the class 1 laser limit.
  • Page 58 5. Connect the network backbone west fiber optic cables to the west (right) OMUX. Job aid The Avaya passive optical multiplexer/demultiplexer (OMUX) sends and receives signals to and from SFP transceivers installed in the switch. It multiplexes and demultiplexes four or eight CWDM wavelengths from a two-fiber (east and west) circuit.

  • Page 59: Removing A Multiplexer

    Removing a multiplexer The following figure shows the CWDM OMUX-8 version, with eight equipment side connections. Figure 1: CWDM OMUX-8 network and equipment side connections Removing a multiplexer OADMs and OMUXs require no power for their operation. You can remove them from the optical shelf after you disconnect them from your network.
  • Page 60 3. Loosen the captive screws on both sides of the module. 4. To release the module, gently pull on both screws at the same time. 5. Slide the module out of the shelf. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 61: Chapter 9: Sfp Specifications

    Bit Error Rate (BER) of 10 SFP labels The Avaya label on a typical SFP contains an Avaya serial number, a bar code, a manufacturer code, an interface type, and a part number.

  • Page 62: General Sfp Specifications

    – 5 to 85C for RoHS -E6 models 0 to 60C for RoHS -E5 models Storage temperature – 40 to 85C Maximum supply current 300 mA unless otherwise stated Maximum power consumption 1.0 W unless otherwise stated Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 63: 100Base-Fx Sfp Specifications

    100BASE-FX SFP specifications 100BASE-FX SFP specifications The 100BASE-FX SFP provides 100 Mbit/s Ethernet Carrier Sense Multiple Access with Collision Detection (CSMA-CD) connectivity using multimode optical fiber. The 100BaseFX uses an LED transmitter. The centre wavelength, spectral width, and optical rise/fall time satisfy the trade-off curves in the FDDI PMD document (ISO/IEC 9314–3:1900).

  • Page 64: 1000Base-T Sfp Specifications

    10 or 100 Mb/s and duplex mode to half or full. The part number for this model is AA1419043-E6. Important: Avaya recommends setting all 1000BaseT ports to auto-negotiate in accordance with the IEEE 802.3ab standard. By default, SFPs inserted into certain product-specific modules are set for autonegotiation = True.

  • Page 65: 1000Base-Sx (Mt-Rj) Sfp Specifications

    1000BASE-SX (MT-RJ) SFP specifications Table 8: IEEE 802.3z 1000BASE-SX (LC) SFP specifications Parameter Specifications Connectors Duplex LC Cabling • 62.5 µm MMF optic cable • 50 µm MMF optic cable Distance • up to 275 m using 62.5 µm MMF optic cable •...

  • Page 66: 1000Base-Lx Sfp Specifications

    Link optical power budget 10.5 dB Transmitter characteristics Launch power – 9.5 to – 3.0 dBm Receiver characteristics Receiver sensitivity – 20 dBm Maximum input power – 3.0 dBm Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 67: 1000Base-Xd Cwdm Sfp Specifications

    CWDM OADM or CWDM OMUX. For more information about how to determine the expected signal loss for an optical add drop multiplexer (OADM), an optical multiplexer (OMUX), or fiber length, see Avaya Ethernet Routing Switch 8800/8600 Planning and Engineering — Network Design, NN46205-200.

  • Page 68: 1000Base-Sx Ddi Sfp Specifications

    Maximum electrical power consumption 1 watt (W) Connector Duplex LC Cabling Data rate 1.0 Gb/s Line rate (8B/10B code) 1.25 Gb/s Link optical power budget 7.5 dB Transmitter characteristics Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 69: 1000Base-Lx Ddi Sfp Specifications

    1000BASE-LX DDI SFP specifications Parameter Specifications Launch power – 9.5 to -4.0 dBm Receiver characteristics Receiver sensitivity – 17 dBm Maximum receiver power 0 dBm 1000BASE-LX DDI SFP specifications This SFP provides 1000BASE-LX gigabit Ethernet connectivity at 1310 nanometers (nm) using single mode or multimode optical fiber.

  • Page 70: 1000Base-Xd Ddi 1550 Nm Sfp Specifications

    Maximum electrical power consumption 1.0 W Connectors Duplex LC Cabling SMF, 9 µm Data rate 1.0 Gb/s Line rate (8B/10B code) 1.25 Gb/s Link optical power budget 22 dB Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 71: 1000Base-Zx Ddi Sfp Specifications

    1000BASE-ZX DDI SFP specifications Parameter Specification Maximum dispersion power penalty 2 dB at 40 km Transmitter characteristics Launch power – 2.0 to 3.0 dBm Receiver characteristics Receiver sensitivity – 24 dBm Maximum receiver power 0 dBm 1000BASE-ZX DDI SFP specifications The following table describes the 1000BASE-ZX DDI SFP.

  • Page 72: 1000Base-Xd Ddi Cwdm Sfp Specifications

    Maximum receiver power – 3.0 dBm 1000BASE-ZX DDI CWDM SFP specifications The following table describes specifications for CWDM SFPs numbered AA1419061-E6 to AA1419068-E6. Caution: Risk of equipment damage Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 73: 1000Base-Bx10 Ddi Sfp Specifications

    1000BASE-BX10 DDI SFP specifications To prevent damage to the optical receiver, ensure that at least 8 dB of attenuation is present between the transmit and receive ports. Table 19: 1000BASE-ZX CWDM SFP DDI (70 km) specifications Parameter Specifications Maximum electrical power consumption 1.0 W Connectors Duplex LC...

  • Page 74: 1000Base-Ex Ddi Sfp Specifications

    The following table describes the 1000BASE-EX DDI SFP. This SFP operates at 1550 nm and has a reach of up to 120 km. The part number of this SFP is AA1419071-E6. Caution: Risk of equipment damage Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 75 1000BASE-EX DDI SFP specifications To prevent damage to the optical receiver, ensure that at least 14 dB of attenuation is present between the transmit and receive ports. To attain the BER of 10 , the minimum attenuation between the transmit and receive ports is 15 dB.
  • Page 76 SFP specifications Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 77: Chapter 10: Sfp+ Specifications

    CPU# [date time] COP-SW INFO Slot #: 1G SFP detected in 10G SFP+ port #. Port offline. In addition, the port is prevented from coming online. This is true even if the inserted part is Avaya- qualified. Important: Passive DACs are not supported but may be recognized. If so, they will display as 10GbOther.

  • Page 78: General Sfp+ Specifications

    Connectors LC ultra physical contact (UPC) Storage temperature –40 to 85C Operating temperature –5 to 85C for RoHS -E6 models 0 to 60C for RoHS -E5 models Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 79: Sfp+ Transceiver Specifications

    SFP+ transceiver specifications SFP+ transceiver specifications The following sections provide specifications for supported SFP+ transceivers: • 10GBASE-SR/SW SFP+ specifications on page 79 • 10GBASE-LRM SFP+ specifications on page 80 • 10GBASE-LR/LW SFP+ specifications on page 83 • 10GBASE-ER/EW SFP+ specifications on page 84 •...
  • Page 80 The stressed sensitivity values are for system level BER measurements, which include the effects of clock and data recovery (CDR) circuits. Avaya recommends that you allocate at least 0.4 dB additional margin if you make component level measurements without the effect of CDR circuits.
  • Page 81 SFP+ transceiver specifications The following table lists the transmitter and receiver specifications for the 10GBASE-LRM SFP +. These parameters meet the IEEE 802.3aq-2006 standard. The part number of this SFP+ is AA1403017-E6. In this table, the OMA, average launch power, and peak power specifications apply at TP2, after accounting for patch cord loss.
  • Page 82 Standards Organization, IEC denotes International Electrotechnical Commission, and OFL denotes Over Filled Launch. The following table uses the 802.3aq standard and specifies the measurement conditions for each fiber type. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 83 SFP+ transceiver specifications Table 26: Launch conditions for each fiber type Parameter Minimum encircled flux Notes Optical launch for OM1 and Uses 62.5 μmmode • 30% within 5 μm radius FDDI-grade fiber conditioning patch cord • 81% within 11 μm radius Optical launch for OM2 and Uses 50 μmmode •...
  • Page 84 1530 to 1565 nm; nominal 1550 nm Distance Up to 40 km Link optical power budget 15 dB Transmitter and dispersion power penalty 3.0 dB at 40 km Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 85 SFP+ transceiver specifications Parameter Specifications Transmitter characteristics Launch power -– 4.7 to 4.0 dBm Minimum side mode suppression ratio 30 dB Minimum launch power in OMA minus – 2.1 dBm transmission and dispersion penalty (TDP) Minimum optical modulation amplitude – 1.7 dBm Maximum average launch power of OFF -–...
  • Page 86 Wavelength range 1280 to 1575 nm. Sensitivity specified for 1530 to 1565 nm. Maximum receiver sensitivity (average -24 dBm power) Maximum receiver (average) power, BER -7.0 dBm Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 87 SFP+ transceiver specifications Parameter Specifications Receiver damage threshold (average power) +5.0 dBm Receiver reflectance (maximum) -27 dB * Achievable link distance is primarily dependent on cable plant insertion loss. 70 km is not possible in some situations. 10GBASE-ER CWDM SFP+ specifications The following table lists the part numbers of the 10GBASE-ER CWDM SFP+ with corresponding wavelengths.
  • Page 88 – 14.1 dBm, P_OMA IEEE 10GBASE-ER Stressed Rx Sensitivity – 11.3 dBm, P_OMA Receiver overload – 1 dBm, P_avg Receiver reflectance – 26 dB Receiver damage threshold +4 dBm Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 89: Chapter 11: Xfp Specifications

    XFPs, be aware that Avaya does not support the use of other XFPs. XFP labels As shown in the following figure, the Avaya label on a typical XFP contains an Avaya serial number, a bar code, a manufacturer code, an interface type, and a part number.

  • Page 90: General Xfp Specifications

    The 10GBASE-SR SFP provides 10 GbE service at 850 nm. The following table lists the specifications for the 10GBASE-SR XFP. The part number of this XFP is AA1403005-E5. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 91 10GBASE-SR XFP specifications For more information about the 10GBASE-SR XFP, including test and measurement information, see the IEEE 802.3ae standard. The 10GBASE-SR XFP is supported by the Ethernet Routing Switch 5530 (not by the 5510 or 5520), and by the Ethernet Routing Switch 5600 Series. Caution: Risk of equipment damage To prevent damage to the optical receiver, ensure that at least 1 dB of attenuation is present...

  • Page 92: 10Gbase-Lrm Xfp Specifications

    The stressed sensitivity values are for system level BER measurements, which include the effects of clock and data recovery (CDR) circuits. Avaya recommends that you allocate at least 0.4 dB additional margin if you make component level measurements without the effect of CDR circuits.
  • Page 93 10GBASE-LRM XFP specifications Parameter Specifications Link optical power budget 1.7 to 1.9 dB, for more information, see Table 36: 10GBASE-LRM channel insertion loss and range on page 93 Maximum transmitter waveform and 4.7 dB dispersion penalty (TWDP) Transmitter characteristics Average launch power –...
  • Page 94 • 81% within 11 μm radius Optical launch for OM3 and — • 30% within 5 μm radius 50 μm fiber • 81% within 11 μm radius Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 95: 10Gbase-Lr/Lw Xfp Specifications

    10GBASE-LR/LW XFP specifications 10GBASE-LR/LW XFP specifications The 10GBASE-LX XFP provides 10 GbE or OC-192 service at a nominal wavelength of 1310 nm. This XFP can attain link lengths of up to 10 km. The following table lists the transmitter and receiver specifications for the 10GBASE-LR/LW XFP.

  • Page 96: 10Gbase-Er/Ew Xfp Specifications

    (8683XLR and 8612XLRS are LAN-only modules, and 8683XZR is a LAN or WAN module). Model numbers ending in R denote a LAN interface; model numbers ending in W denote a WAN interface. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 97 10GBASE-ER/EW XFP specifications Table 39: IEEE 802.3ae 10GBASE-ER/EW XFP specifications Parameter Specifications Line rate (nominal) 10GBASE-ER 10.3125 Gb/s ±100 ppm (10 GbE) 10GBASE-EW 9.95328 Gb/s ±20 ppm (OC-192) MTBF 675 000 hours Center wavelength range 1530 to 1565 nm; nominal 1550 nm Distance Up to 40 km Link optical power budget...

  • Page 98: 10Gbase-Zr/Zw Xfp Specifications

    Side mode suppression ratio (minimum) 30 dB Average launch power 0 to 4.0 dBm Optical modulation amplitude (minimum) – 1.7 dBm Average launch power of OFF transmitter – 30 dBm (maximum) Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 99 10GBASE-ZR/ZW XFP specifications Parameter Specifications Extinction ratio (ER) minimum 3.5 dB end of life maximum 7.0 dB start of life OMA (maximum) – 128 dB/Hz Maximum optical return loss tolerance – 26 dB Maximum transmitter reflectance – 12 dB Receiver characteristics Wavelength range 1280 to 1575 nm.
  • Page 100 XFP specifications Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 101: Chapter 12: Multiplexer Specifications

    Chapter 12: Multiplexer specifications This section describes multiplexer specifications. Use the specifications to help ensure proper network operation. Multiplexer loss values include connector loss. One nanometer (nm) offset exists between the stated wavelength for the Coarse Wavelength Division Multiplexing (CWDM) SFP and the CWDM optical add drop multiplexers (OADM) due to a shift in the center wavelength of the CWDM SFP as it reaches typical system operating temperature.
  • Page 102 4.5 dB Sigma TX to RX Network (Mux) 0.4 dB 0.5 dB RX to TX Network (Demux) 0.4 dB 0.5 dB Isolation > 10 dB > 10 dB Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 103 Parameter Specification Demux > 50 dB > 50 dB Directivity < -55 dB Optical OMUX Wavelengths 1491 nm 1471 nm 1531 nm 1491 nm 1571 nm 1511 nm 1611 nm 1531 nm 1551 nm 1571 nm 1591 nm 1611 nm Installation —...
  • Page 104 Multiplexer specifications Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 105: Appendix A: Translations Of Safety Messages

    Appendix A: Translations of Safety Messages This section contains translations of precautionary notices that you must read and follow for safe operation of the Ethernet Routing Switch. Electromagnetic interference caution statement Caution: This device is a Class A product. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users are required to take appropriate measures necessary to correct the interference at their own expense.

  • Page 106: Electrostatic Discharge Caution Statement

    Instandhaltung dieses Produkts immer ein antistatisches Band am Handgelenk, das mit einer ESD-Buchse verbunden ist. Stellen Sie sicher, dass das Band am Handgelenk Kontakt zur Haut hat. Electrostatic alert: PRECAUCIÓN ESD (Descarga electrostática) Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 107: Laser Eye Safety Warning Statement

    Laser eye safety warning statement Para prevenir el daño producido por una descarga electrostática, use siempre una pulsera antiestática conectada a un enchufe de descarga electrostática (ESD) al realizar el mantenimiento de este producto. Asegúrese de que la pulsera antiestática haga contacto con su piel.

  • Page 108: Laser Eye Safety Connector Inspection Warning Statement

    Risk of eye injury When inspecting a connector, ensure that light sources are off. The light source used in fiber optic cables can damage your eyes. Warning: AVERTISSEMENT Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 109: Connector Cleaning Safety Warning Statement

    Connector cleaning safety warning statement Risques de blessure oculaire Assurez-vous que toutes les sources de lumière ont été désactivées avant de procéder au contrôle d'un connecteur. La source de lumière utilisée dans les câbles de fibres optiques risque de provoquer des lésions oculaires. Warning: WARNUNG Verletzungsrisiko der Augen...
  • Page 110 óculos de segurança ao trabalhar com lata de ar comprimido. Para evitar irritação dos olhos, use óculos de segurança ao trabalhar com álcool isopropílico. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 111: Multiplexing And Power Safety Warning Statement

    Multiplexing and power safety warning statement Warning: AVVISO Rischio di lesioni agli occhi Quando si esamina un connettore, assicurarsi che le sorgenti di luce siano spente. La sorgente di luce utilizzata nei cavi a fibre ottiche potrebbero danneggiare gli occhi. Per evitare l'accidentale introduzione di detriti negli occhi, indossare gli occhiali di sicurezza quando si lavora con un'impolveratrice ad aria compressa.

  • Page 112: Optical Fiber Damage Caution Statement

    électriques lourds car leur poids risquerait de les endommager. Caution: ACHTUNG Risiko von Geräteschäden Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 113: Optical Fiber Connector Damage Caution Statement

    Optical fiber connector damage caution statement Das Glasfaserkabel darf nicht zerdrückt werden. Wenn sich ein Glasfaserkabel zusammen mit großen und schweren Elektrokabeln im gleichen Kabelkanal oder in der gleichen Führung befindet, kann es durch das Gewicht der Elektrokabel beschädigt werden. Caution: PRECAUCIÓN Riesgo de daños en los equipos...
  • Page 114 ótico. Para evitar a transferência de óleo ou outro agente contaminador de seus dedos para a extremidade final da ponteira, manuseie os conectores com cuidado. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 115: Sfp Damage Caution Statement

    SFP damage caution statement Caution: ATTENZIONE Rischio di danno all'apparecchio Per evitare ulteriori contaminazioni, pulire l'apparecchio a fibre ottiche solo in presenza di evidente contaminazione. Per evitare contaminazioni, assicurarsi che le porte ottiche di tutti i dispositivi attivi siano coperte da un tappo antipolvere o da un connettore ottico. Per evitare il trasferimento di olio o di altri agenti contaminanti dalle dita alla parte finale della ghiera, maneggiare con cura i connettori.

  • Page 116: Sfp+ Damage Caution Statement

    Afin d'éviter tout risque d'insertion incorrecte, les modules SFP+ sont verrouillés. Si vous ne parvenez pas à insérer un module SFP+, ne forcez pas. Retournez-le et renouvelez l'opération. Caution: VORSICHT Risiko von Geräteschäden Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 117: Xfp Damage Caution Statement

    XFP damage caution statement Die SFP+s sind so konstruiert, dass ein falsches Einsetzen verhindert wird. Lässt sich ein SFP+ auch auf Druck hin nicht einsetzen, versuchen Sie nicht, es gewaltsam einzusetzen, sondern drehen Sie es um, und setzen Sie es erneut ein. Caution: PRECAUCIÓN Riesgo de daños en los equipos...
  • Page 118 ATTENZIONE Rischio di danni all'apparecchio Gli XFP dispongono di chiavi in modo da evitarne l'inserimento errato. Se l'XFP resiste alla pressione, non forzarlo ma capovolgerlo e reinserirlo. Installation — SFP, SFP+, XFP, and OADM Hardware Components August 2013 Comments? infodev@avaya.com...

This manual is also suitable for:

8600 series

Table of Contents