ATTO Technology iPBridge 2600 Installation And Operation Manual page 57

ReadOnlyPassword
Specifies a read only password for all sessions: TCP/IP,
FTP and ExpressNAV web-based interface. You are
prompted for the current password, to enter the new
password, and to confirm the new password. Passwords
are case sensitive, 0-32 characters with no spaces.An
empty password can be configured by entering the
Password confirmation prompts with no parameters. The
command RestoreConfiguration default sets the
password to its default value.
Default: Password
set ReadOnlyPassword
Requires a SaveConfiguration command
ReadOnlyUsername
Specifies a read only user name for all TCP/IP, FTP and
ExpressNAV web server sessions. User name is case
insensitive, 1-32 characters with no spaces.
Default: user
set ReadOnlyUsername
Requires a SaveConfiguration command
get Username
RMON
Collects and stores Ethernet data on data ports at
specified intervals.
Refer to
http://tools.ietf.org/html/rfc2819
You can display the entire table requested, or a single
entry based on the index (and sample index for the
Ethernet History table). Setting the history control entries
takes effect immediately, but changes must be saved to be
persistent over a reboot.
Default: See Exhibit 7.1-7 on page 48.
get RMON [ethernetStat | historyControl] <idx>
Valid range for ethernetStat: 1-3
Valid range for historyControl: 1-6
Lists the contents of either the Ethernet Statistics table
(statistics measured by the probe for each monitored
Ethernet interface on the device) of the History Control
table (periodic statistical sampling of data from various
Exhibit 7.1-7 RMON command: default history Control table (buckets and interval in hexadecimal).
Idx DataSrc
====================================================================
001 43.6.1.2.1.2.2.1.1.1 00000032 00000032 0000001e monitor 00000004
002 43.6.1.2.1.2.2.1.1.1 00000032 00000032 00000708 monitor 00000004
003 43.6.1.2.1.2.2.1.1.2 00000032 00000032 0000001e monitor 00000004
004 43.6.1.2.1.2.2.1.1.2 00000032 00000032 00000708 monitor 00000004
005 43.6.1.2.1.2.2.1.1.3 00000032 00000032 0000001e monitor 00000004
006 43.6.1.2.1.2.2.1.1.3 00000032 00000032 00000708 monitor 00000004
BktReq BktGrant Interval Owner
types of networks). If idx is not specified, the entire table
is listed.
get RMON [ethernetHistory] <idx sampleIdx>
Valid range for ethernetHistory idx: 1-6
Valid range for ethernetHistory sampleIdx: 1-180
Lists the contents of the Ethernet History table (a
collection of periodic statistcial examples from an
Ethernet network). If idx sampleIdx is not specified, the
entire table is listed. Entries in the Ethernet History table
are not valid when the Sample Index is 0.
set RMON [idx] [bucketsRequest] [interval] [valid | invald ]
Valid range for bucketsRequest: 1-180
Valid range for interval: 1-3600
Sets values in the History Control table to control the
sampling period (interval is specified in seconds). Can
also be used to set entries in the History Control table to
valid or invalid.
Username
Specifies a user name for all TCP/IP, FTP and
ExpressNAV web server sessions. Username is case
insensitive, 1-32 characters with no spaces.Changes to
the Admin Level user name requires an Admin Level
password.
Default: root
set Username
Requires entering a password
Requires a SaveConfiguration command
get Username
VLAN
Creates up to eight Virtual LAN IDs for each Ethernet
data port. Each VLAN ID is assigned a VLAN name of up
to 64 characters. If no VLALN ID exists for a data port,
VLAN is disabled for that port.Refer to
Virtual Local Area Network on page 14
set VLAN [dp [n]] [[VLAN ID] [VLAN Name] <delete>| [all]
[delete]]
Requires a SaveConfiguration command
get VLAN [dp[n]]
Status
Set up a VLAN:
48
Interfaces: CLI