1 ATTO iPBridge provides storage options ...1 iPBridge 1500/1550 features 1.1 ATTO iPBridge 1500D ...3 Dimensions Environment Power SCSI port Ethernet port LED indicators Reset switch 1.2 ATTO iPBridge 1500E ...5 Dimensions Environment Power Reset switch SCSI port Ethernet port...
Page 5
2.1 Target management ...13 Target names Default target node Map devices automatically Map devices manually Multiple target nodes Automatically configure multiple targets Manually configure multiple target nodes 2.2 System setup options ...19 Change mapping Change the current user name, password Create a read only password or user name Performance optimization Set up a VLAN: Virtual Local Area Network...
Page 6
6 ExpressNAV provides web-based interface ...29 Optimizing ExpressNAV in Internet Explorer Opening an ExpressNAV session 6.1 ExpressNAV pages ...31 Status Serial Port Configuration Time & Date Configuration Ethernet Port Configuration Remote Management SCSI Configuration iSCSI Configuration Automatic iSCSI Target Management iSCSI Target Management (Manual) Bridge Configuration Firmware Update...
Page 9
Appendix C Glossary ...v Appendix D Safety standards and compliances ...vi Appendix E ATTO accessories ...viii Appendix F Contact ATTO Technology, Inc..ix...
To make sure you have the most up-to-date version of the firmware, visit the ATTO Technology website, www.attotech.com ATTO Technology Inc. iPBridge Installation and Operation Manual iPBridge 1500/1550 features • One independent Gigabit Ethernet port and one independent Ultra 160 SCSI port •...
1.1 ATTO iPBridge 1500D The ATTO iPBridge 1500D is a 1-Gigabit Ethernet to SCSI embeddable bridge for midrange performance, cost effective solutions in SMB/SME environments. The iPBridge 1500D includes a single Ethernet port which may be used for either data transfer or configuration, a serial management port and a SCSI port.
Page 13
Exhibit 1.1-1 iPBridge 1500D back panel power air vents connector Ethernet Ethernet SCSI port Power speed LED activity LED activity LED Installation: ATTO iPBridge 1500D...
68-pin “P” interface: 160 MB/sec. maximum throughput, downward compatible with all forms of single-ended SCSI. ATTO Technology Inc. iPBridge Installation and Operation Manual The iPBridge supports SCSI devices including hard disk drives, tape drives RAID controllers, DVD, MO and CD libraries.
Page 15
Exhibit 1.2-1 iPBridge 1500E board layout Mounting hole Mounting hole Reset SCSI Activity pin 1 Serial port Mounting hole Ethernet port Exhibit 1.2-2 iPBridge 1500E board profile and dimensions E t h e r n e t P o r t E t h e r n e t P o r t .
The iPBridge supports SCSI devices including hard disk drives, tape drives, RAID controllers, DVD and CD libraries. ATTO Technology Inc. iPBridge Installation and Operation Manual Ethernet port The 100/1000 GbE RJ45 Ethernet port uses the Intel 8254x family gigabit Ethernet chipset to...
Page 17
Exhibit 1.3-1 iPBridge 1550D back panel Serial air vents SCSI port Ethernet port port power connector Ready/SCSI Activity Speed Power port activity Reset switch Installation: ATTO iPBridge 1550D...
68-pin “P” interface: 160 MB/sec. maximum throughput, downward compatible with all forms of single-ended SCSI. ATTO Technology Inc. iPBridge Installation and Operation Manual The iPBridge supports SCSI devices including hard disk drives, tape drives, RAID controllers, DVD, MO and CD libraries.
Page 19
Exhibit 1.4-1 iPBridge 1550E board layout Mounting hole Mounting hole Reset SCSI Activity pin 1 Serial port Mounting hole Ethernet port Exhibit 1.4-2 iPBridge 1550E board profile and dimensions E t h e r n e t P o r t E t h e r n e t P o r t .
• The switch(es) must allow UDP broadcast messages to be passed through. ATTO Technology Inc. iPBridge Installation and Operation Manual • No router is in place between the computer and the iPBridge. • If you are managing your iSCSI system...
• If you wish to view information about the unit or make any changes, use the ExpressNAV interface by clicking Launch Browser. Refer to ExpressNAV provides web-based interface page 29 and ExpressNAV pages Install MS iSCSI Initiator for Windows Download the latest version of Microsoft Software Initiator from www.microsoft.com/downloads.
When the action is complete, the iSCSI Target Management page appears. From there you ATTO Technology Inc. iPBridge Installation and Operation Manual If you divide the default single target node into multiple target nodes, you must set up access to each node separately.
Multiple target nodes Multiple targets allow you to create a more configurable mapping scheme which can segregate storage into different iSCSI nodes within the iPBridge, with each iSCSI target having its own set of access criteria. For example, if you have two servers and a library with four tapes and a media changer, the default node would provide both servers access to all tapes and the media changer (default target mode).
Page 26
Exhibit 2.1-3 Automatic iSCSI Target Management page and the results of clicking either Map all devices to the default target or Map each device to its own target. Unmapped SCSI devices ATTO Technology Inc. iPBridge Installation and Operation Manual...
Note The user name is case insensitive and password is case sensitive. Click Submit. ATTO Technology Inc. iPBridge Installation and Operation Manual The user name and password for all Telnet, FTP and ATTO ExpressNAV sessions are changed. Create a read only password or user name You may set a read only password or a read only user name.
On the menu presented, go to the Microsoft VM, Java permissions and make sure Disable Java is not selected. Go to the Miscellaneous topic and select METAREFRESH Set up a VLAN: Virtual Local Area Network A Virtual LAN (VLAN) is a group of devices on the same physical LAN which can communicate with each other as if they were all on different physical LANs.
• All means warnings, critical events and informational messages are sent. • Critical means only critical event notifications are sent. ATTO Technology Inc. iPBridge Installation and Operation Manual • Warning means only warnings and critical event notifications are sent. • None means no notification is sent.
The iPBridge firmware is distributed as a compressed .zip file and can be obtained from the ATTO Technology, Inc. web site or by contacting ATTO Technical Support at www.attotech.com Preliminary steps The iPBridge firmware is distributed as a compressed .zip file and can be obtained from...
Check for problems on attached devices Check the following in order to find problems on attached devices: • LEDs ATTO Technology Inc. iPBridge Installation and Operation Manual 5 Troubleshooting using the CLI directly (refer to ExpressNAV based interface...
Check host versions Check the following to find problems on attached hosts: • Operating system version • Service pack version • Host adapter version • Host adapter firmware version Check iPBridge product versions For a current list of required updates, visit www.attotech.com.
Refer to Ping on page 49. ATTO Technology Inc. iPBridge Installation and Operation Manual If the host cannot ping the iPBridge ports and the iPBridge ports are properly configured, continue to the Local Area Network/Wide Area Network section, page 25.
NICs come in two types: accelerated and un- accelerated. Accelerated NICs use some hardware to offload some of the TCP processing from the host. Un- accelerated NICs make the OS do all TCP processing. To check the iSCSI host adapter or NIC Check cable integrity.
23. The current optimized frame size for the iPBridge is 9k. Smaller frame sizes can cause a decrease in performance. ATTO Technology Inc. iPBridge Installation and Operation Manual Checking the LAN/WAN Verify that the MTU size is set to optimal setting for the LAN/WAN environment.
optimal size for the particular SCSI device(s) connected to the iPBridge. Checking the host system The faster the host, the faster your transfer times are. The work flow goes only as fast as the slowest connection in the host system, so transferring data from an IDE drive, 100Mb connection, a DLT 4000, a high speed RAID volume across the country, or other applications, slows the system no matter how fast...
Select the Custom Level button. On the menu presented, go to the Microsoft VM, Java permissions and make sure Disable Java is not selected. ATTO Technology Inc. iPBridge Installation and Operation Manual Go to the Miscellaneous topic and select METAREFRESH. Opening an ExpressNAV session Point your browser at the IP address of the iPBridge.
Page 39
Exhibit 6.0-1 A typical ExpressNAV page. Ethernet port icon Product faceplate graphic provides links to specified port Sidebar: select the item you wish to view Parameter name Red print provides link to help text Serial port icon SCSI port icon Submit button same as typing all CLI commands and saveconfigruation norestart...
Refer to commands on page 43 for detailed information. SCSI Configuration Controls the SCSI port for the following parameters: ATTO Technology Inc. iPBridge Installation and Operation Manual • Bus speed • Sync transfer • Wide transfer • Initiator ID •...
Bridge Configuration Defines a name for the bridge, sets an administrator user name and password, a read only user name and password, restores defaults and controls the Identify Bridge feature. Refer to Maintenance commands details on each parameter. Firmware Update You may update firmware using ExpressNAV.
To verify that you have connected successfully, type help after the Ready prompt and press Enter. ATTO Technology Inc. iPBridge Installation and Operation Manual • If a list of all available commands does not appear on the screen, review the steps in this section, check the cable, or contact service personnel until the problem is solved.
Page 43
Exhibit 7.0-1 Start up messages. ATTO iPBridge 1550 (c) 2002 - 2006 ATTO Technology, Incorporated. Firmware version 3.70 release date Apr Base version 9.00 126 Megabytes of RAM Installed. 1 GbE Data Port(s). 1 Ultra160 SCSI Interface Port(s). World Wide Name = 20 00 00 10 86 20 02 A3 Serial Number = "IP1550L10001"...
(6 – 9 = 6, 7, 8, 9) ATTO Technology Inc. iPBridge Installation and Operation Manual • The set form is an action that changes the value of a parameter or configuration setting. It may require a SaveConfiguration command and a restart of the system before it is implemented.
CLI Error Messages The following error messages may be returned by the Command line Interface: ERROR. Invalid Command. Type 'Help' for command list. ERROR. Wrong/Missing Parameters Usage: <usage string> ERROR. Command Not Processed. Exhibit 7.1.1-1 If you enter a parameter for a CLI command incorrectly, the CLI help file displays with an error message.
0.0.0.0 IsReserved Password Password Ping ReadOnlyPassword Password ReadOnlyUsername user ATTO Technology Inc. iPBridge Installation and Operation Manual Defaults set accesscontrol default enabled set accessentry discovery all automap automaponboot disabled automaponbootdelay 60 get bridgemodel set bridgename Omega6 cleareventlog set date 03/25/1951...
ExpressNAV web server sessions. Username is case insensitive, 1-32 characters with no spaces. Default: user set ReadOnlyUsername [username] ATTO Technology Inc. iPBridge Installation and Operation Manual Requires a SaveConfiguration command RestoreConfiguration Restores configuration to either the default configuration or the configuration last saved into non-volatile memory.
VerboseMode Specifies the detail of feedback for the command line interface. Disabling this option removes parameter names from action commands and removes descriptions from information commands. Choices are enabled or disabled Default: enabled (returns have parameter information) set VerboseMode [enabled | disabled] get VerboseMode CLI commands...
The saved option undoes any changes made since the last save. RestoreConfiguration [Default | Saved] ATTO Technology Inc. iPBridge Installation and Operation Manual System setup options on page 19. SCSIPortReset Resets the specified SCSI bus.
SpeedWrite When enabled, improves the performance of SCSI WRITE commands to SCSI devices attached to the iPBridge. Specify SCSI bus (sb), target (st), LUN (sl) of a mapped SCSI device or (all) for each currently mapped device. set SpeedWrite SCSI [sb st sl | all] [enabled|disabled] get SpeedWrite SCSI [sb st sl | all] SpeedWriteDefault When enabled, SpeedWrite performance enhancement is...
Page 52
When enabled, records various system events to the event log. Default: enabled set EventLog [enabled|disabled] Requires a SaveConfiguration command get EventLog ATTO Technology Inc. iPBridge Installation and Operation Manual Remote system monitoring on page 21. Help Lists available commands. If command name is specified, displays detailed command-specific information.
Page 53
RMON RMON collects and stores Ethernet data on data ports at specified intervals. You can display the entire table requested, or a single entry based on the index (and sample index for the Ethernet History table). Entries in the Ethernet History table are not valid when their Sample Index is 0.
Page 54
SCSIPortSelTimeout [sb] SCSIPortSyncTransfer Specifies whether synchronous SCSI transfers should be negotiated with devices on the specified SCSI port. ATTO Technology Inc. iPBridge Installation and Operation Manual Default: enabled set SCSIPortSyncTransfer [[sb [enabled | disabled] ] Requires a SaveConfiguration command...
Page 55
SpeedWriteDefault When enabled, SpeedWrite performance enhancement is set as the default for any subsequent SCSI devices mapped manually or via an AutoMap operation. If disabled, the iPBridge does not attempt SpeedWrite performance enhancement to newly-mapped SCSI devices. Default: disabled set SpeedWriteDefault [enabled | disabled] get SpeedWriteDefault VirtualDriveResponse Allows the iPBridge to provide proxy responses to SCSI...
Page 56
SerialPortBaudRate [2400 | 9600 |19200 | 38400 | 57600 |115200] Requires a SaveConfiguration command get SerialPortBaudRate ATTO Technology Inc. iPBridge Installation and Operation Manual SerialPortEcho Enables/disables/reports the echoing of keyboard input. When enabled, all non-control character keyboard input is output to the display. Local ASCII terminal (or terminal...
Page 58
Default: enabled set IPDHCP [dp0|all] [enabled | disabled] Requires a SaveConfiguration command get IPDHCP dp0 ATTO Technology Inc. iPBridge Installation and Operation Manual IPGateway Controls the current gateway. If IPDHCP is enabled (see above), get command reports the current IP gateway assigned by the network DHCP server.
Page 59
ReadOnlyPassword Specifies a read only password for all sessions: Telnet, FTP and ExpressNAV web-based interface. You are prompted for the current password, to enter the new password, and to confirm the new password. Passwords are case sensitive, 0-32 characters with no spaces.An empty password can be configured by entering the password confirmation prompts with no parameters.
Page 60
Account Name (optionally the Initiator Name) and secret pair. The Account Name ATTO Technology Inc. iPBridge Installation and Operation Manual can be 1 to 223 characters. Account Names are case sensitive. Account name can not be all.
Page 61
iSCSITargetNameDisplay Displays the iSCSI target name. iSCSITargetNameDisplay iSCSIWANIPAddress Sets the IP address reported from the host. Setting the address to 0.0.0.0 causes the unit to report the LAN IP address. Default: 0.0.0.0 set iSCSIWANIPAddress [dp0 | all] [xxx.xxx.xxx.xxx] get iSCSIWANIPAddress [dp0 | all] iSNSLoginControl Specifies whether the iPBridge delegates its access control/authorization to an iSNS server.
Page 62
Default: enabled set AutoMapOnBoot [enabled | disabled] Requires a SaveConfiguration command get AutoMapOnBoot ATTO Technology Inc. iPBridge Installation and Operation Manual on page 13. AutoMapOnBootDelay Controls automatic device detection and mapping (automap) at bridge startup with a delay of up to 4.25 minutes (1-256 seconds).
Page 63
RouteDisplay Displays a combined list of the host protocol address to target destination device mappings. RouteDisplay iSCSI [default <lun> | Target Name <lun>] SCSIInitID Specifies the persistent SCSI initiator ID to be used on the specified SCSI port. All maps coinciding with the user- specified SCSIInitID are destroyed upon issuing this command.
Page 64
ExpressNAV web management iSCSI SANS Configuration save and restore ATTO Technology Inc. iPBridge Installation and Operation Manual into products throughout the family as much as possible, requiring only an upgrade of firmware to incorporate them into your SAN (Storage Area Network) or NAS (Network Attached Storage).
Page 65
FibreBridge Product features Number of FC ports FC interface Data transfers Number of SCSI ports SCSI interface Sustained data transfer rate (MB/sec.) Configurations Full duplex data transfers Supports Class 2 transfers Class 3 transfers intermix transfers direct fabric connect error recovery Bridge management available Serial Ethernet...
SCSI port. Each SCSI port is a bus capable of supporting 15 devices and each bus is capable of 40, 80 or 160 ATTO Technology Inc. iPBridge Installation and Operation Manual Appendix B Cabling Examples The SCSI specification limits total bus cable...
Each SCSI bus auto-negotiates the appropriate sync rates with the connected devices. If slower devices are mixed with faster devices, the bus communicates at the rate of the slowest device, thus wasting the performance capabilities of the faster devices. Connect slower devices to one SCSI port and connect faster devices to the other port.
SNTP Simple Network Time Protocol: uses a server to set the time and date over the Ethernet port. Target Node iSCSI synonym for zone ATTO Technology Inc. iPBridge Installation and Operation Manual and the IETF ( www.ietf.org Definition...
Appendix D Safety standards and compliances The equipment described in this manual generates and uses radio frequency energy. If this equipment is not used in strict accordance with the manufacturer's instruction, it can and may cause interference with radio and television reception. See the Technical Specification sheet for a full list of certifications. WARNING Risk of explosion if battery is removed and/or replaced by an incorrect type.
Page 70
This Declaration will only be valid when this product is used in conjunction with other CE approved devices and when the entire system is tested to the applicable CE standards and found to be compliant. ATTO Technology Inc. iPBridge Installation and Operation Manual...
Appendix E ATTO accessories The following accessories are available through ATTO Technology. Contact an ATTO Technology authorized sales representative to order. iSCSI Bridge board-level models ATTO iPBridge 2600C IPBR-2600-CR0 4 Gigabit Ethernet by 2 LVD Ultra320 SCSI ATTO iPBridge 2700C...
155 CrossPoint Parkway Amherst, New York 14068 (716) 691-1999 • voice (716) 691-9353 • fax www.attotech.com ATTO Technology can also be reached via e-mail at the following addresses: Sales Support: sls@attotech.com Technical Support:techsupp@attotech.com ATTO Technology Inc. iPBridge Installation and Operation Manual...