Removing The Camera From The Housing - Fantasea Line FRX100 VA R Instruction Manual

6. Gently try pulling the back door away from the front door. If the housing is properly closed, it should Gently try pulling the back door away from the front door. If the housing is properly closed, it should Gently try pulling the back door away from the front door. If the housing is properly closed, it should
be impossible to open the back door. be impossible to open the back door.
7. Visually inspect the black O-ring
sure it isn't twisted or out of the groove and that no foreign matter has been caught in the seal, sure it isn't twisted or out of the groove and that no foreign matter has been caught in the seal sure it isn't twisted or out of the groove and that no foreign matter has been caught in the seal
such as secure lines, sand, grit, hairs or any other foreign substance.
8. Turn the camera on and check that the
extended camera lens does not catch or extended camera lens does not catch or
bend the black rubber seat on the inside bend the black rubber seat on the inside
of the lens port. It is vital that this rubber of the lens port. It is vital that this rubber
seat does not disturb the lens (image seat does not disturb the lens (image
#18).
9. Test housing control buttons to make Test housing control buttons to make
sure that the camera was properly at the camera was properly
installed inside the housing and that installed inside the housing and that
nothing interferes with normal operation nothing interferes with normal operation
of the camera. It is recommended to take of the camera. It is recommended to take
a few images once the camera has been a few images once the camera has been
installed inside the housing and prior to installed inside the housing and prior to
the dive in order to ensure proper operation.
10. If making use of the internal camera
flash diffuser on the housing and attach the flash diffuser quick release secure string in order to flash diffuser on the housing and attach the flash diffuser quick release secure string in order to flash diffuser on the housing and attach the flash diffuser quick release secure string in order to
avoid losing it underwater.
11. Prior to diving with the housing, submerge Prior to diving with the housing, submerge it in a shallow tub of water or rinse tank
the housing to make sure no bubbles are escaping from it and that no water is entering. the housing to make sure no bubbles are escaping from it and that no water is entering. the housing to make sure no bubbles are escaping from it and that no water is entering.
12. If a Vacuum Safety System is made use of, perform a pre If a Vacuum Safety System is made use of, perform a pre-dive check to confirm the watertight seal of
the housing. See "Hybrid Vacuum Safety System" section for further instructions. the housing. See "Hybrid Vacuum Safety System" section for further instructions. the housing. See "Hybrid Vacuum Safety System" section for further instructions.

REMOVING THE CAMERA FROM THE HOUSING

1. After use, thoroughly rinse the housing fresh water. P , thoroughly rinse the housing fresh water. Prior to opening the housing, make sure
both your hands and the housing are clean and dry. It is recommended to have a clean, dry both your hands and the housi
soft towel handy in order to dry your hands and the water drops on the housing. soft towel handy in order to dry your hands and the water drops on the housing. soft towel handy in order to dry your hands and the water drops on the housing.
2. Prior to opening a vacuumed housing, the vacuum should be released using the Vacuum Valve. Prior to opening a vacuumed housing, the vacuum should be released using the Vacuum Valve. Prior to opening a vacuumed housing, the vacuum should be released using the Vacuum Valve.
For further instructions, please refer to the section "Fantasea Hybrid Vacuum Safety System".
3. When opening the housing, it is important to hold it so the lens port is facing down. This will opening the housing, it is important to hold it so the lens port is facing down. This will opening the housing, it is important to hold it so the lens port is facing down. This will
prevent the camera from slipping out of the housing while being opened. prevent the camera from slipping out of the housing while being opened.
ring through the transparent back door for proper closure.
sand, grit, hairs or any other foreign substance.
check that the
roper operation.
camera flash, install the removable
FROM THE HOUSING
tions, please refer to the section "Fantasea Hybrid Vacuum Safety System". tions, please refer to the section "Fantasea Hybrid Vacuum Safety System".
check to confirm the watertight seal of
rior to opening the housing, make sure
FRX100 VA R Housing Instruction Manual
21
for proper closure. Make
Image #18
rinse tank. Carefully look at
to have a clean, dry and
Instruction Manual 20200225