Removing The Camera From The Housing; Using The Camera Built-In Flash - Fantasea Line FG7X III R Instruction Manual

7. Turn the camera on and check that the
extended camera lens does not catch or extended camera lens does not catch or
bend the black rubber seat on the inside of bend the black rubber seat on the inside of
the lens port. It is vital that this rubber seat
does not disturb the lens (image does not disturb the lens (image #14).
8. Test housing control buttons to make sure Test housing control buttons to make sure
that the camera was properly installed that the camera was properly installed
inside the housing and that nothing inside the housing and that nothing
interferes with normal operation of the interferes with normal operation of the
camera. It is recommended to take a few
images once the camera has been installed images once the camera has been installed
inside the housing and prior to the dive in inside the housing and prior to the dive in
order to ensure proper operation. order to ensure proper operation.
9. If making use of the internal camera
flash diffuser on the housing and attach the flash diffuser quick release secure string in order to flash diffuser on the housing and attach the flash dif
avoid losing it underwater.
10. Prior to diving with the housing, submerge it in Prior to diving with the housing, submerge it in a shallow tub of water or rinse tank
the housing to make sure no bubbles are escaping from it and that no water i the housing to make sure no bubbles are escaping from it and that no water is entering. the housing to make sure no bubbles are escaping from it and that no water i
11. If a Vacuum Safety System is made use of
the housing. See "Hybrid Vacuum Safety System" section for further instructions. the housing. See "Hybrid Vacuum Safety System" section for further instructions. the housing. See "Hybrid Vacuum Safety System" section for further instructions.

REMOVING THE CAMERA FROM THE HOUSING

1. After use, thoroughly rinse the housing fresh water. P , thoroughly rinse the housing fresh water. Prior to opening the housing, make sure
both your hands and the housing are clean and dry. It is recommended to have a clean, dry both your hands and the housing are clean and dry.
soft towel handy in order to dry your hands and the water drops on the housing.
2. Prior to opening a vacuumed housing, the vacuum should be released using the Vacuum V Prior to opening a vacuumed housing, the vacuum should be released using the Vacuum Valve. Prior to opening a vacuumed housing, the vacuum should be released using the Vacuum V
For further instructions, please refer to the section "Fantasea Hybrid Vacuum Safety System". For further instructions, please refer to the section "Fantasea Hybrid Vacuum Safety System". For further instructions, please refer to the section "Fantasea Hybrid Vacuum Safety System".
3. When opening the housing, it is important to hold it so the lens port is facing down. This will opening the housing, it is important to hold it so the lens port is facing down. This will opening the housing, it is important to hold it so the lens port is facing down. This will
prevent the camera from slipping out of the housing while being opened. prevent the camera from slipping out of the housing while being opened.
4. Open the housing as described
camera from the housing. Take sufficient care that no water drips from your hair and body onto
the housing and camera.

USING THE CAMERA BUILT-IN FLASH

1. The Canon G7 X Mark III camera
subjects. For stronger lighting, illuminating For stronger lighting, illuminating subjects that are farther away, avoiding backscatter,
check that the
vital that this rubber seat
to take a few
camera flash, install the removable
made use of, perform a pre-dive check to confirm the watertight seal of
FROM THE HOUSING
order to dry your hands and the water drops on the housing. order to dry your hands and the water drops on the housing.
bed in the section "Opening the Housing" and carefully remove
Take sufficient care that no water drips from your hair and body onto Take sufficient care that no water drips from your hair and body onto
IN FLASH
camera has a built-in flash capable of illuminating nearby underwater
fuser quick release secure string in order to
check to confirm the watertight seal of
rior to opening the housing, make sure
FG7X III R Housing Instruction Manual
19
Image #14
rinse tank. Carefully look at
to have a clean, dry and
carefully remove the
nearby underwater
avoiding backscatter,
Instruction Manual 20200220