Table of Contents
Advertisement
CARE & MAINTENANCE
CARE & MAINTENANCE
The Fantasea FRX100 VA R Housing require
performance. The following tips will enable you to get the best results:
performance. The following tips will ena
1. Always rinse your housing in streaming
water tub or rinse tank for about 20 minutes after every dive in order to dissolve the salt
water crystals from around the controls and openings of the housing.
water crystals from around the controls and openings of the housing. Manipulate each of the
movable controls to assist the removal of salt particles from these tight areas.
movable controls to assist the removal of salt particles from these tight areas.
movable controls to assist the removal of salt particles from these tight areas.
2. Allow the housing to dry thoroughly before packing away for the day or for the trip home.
using to dry thoroughly before packing away for the day or for the trip home.
using to dry thoroughly before packing away for the day or for the trip home.
You may use a soft towel or cloth to dry the housing. Be sure there is no grease or other
You may use a soft towel or cloth to dry the housing. Be sure there is no grease or other
You may use a soft towel or cloth to dry the housing. Be sure there is no grease or other
debris on the towel.
3. Visually check the condition of the
Visually check the condition of the black O-ring before every dive. If it is dirty, clean it with
fresh water and dry it with a soft cloth as described
fresh water and dry it with a soft cloth as described throughout the manual. If it is damaged
in any way, such as cut or perforated, replace it
in any way, such as cut or perforated, replace it before using the housing again.
4. It is recommended to slightly lubricate the
It is recommended to slightly lubricate the black O-ring periodically. It's important to note
that the amount of lubrication required on the O
the amount of lubrication required on the O-ring is only enough to allow it to slip into
place without friction, so it does not twist or become dislodged. More grease is not
place without friction, so it does not twist or become dislodged.
necessarily better, and in some
5. Use only the supplied silicone grease for lubricating the
other grease might impair the watertight seal of the housing.
other grease might impair the watertight seal of the housing.
6. Avoid removing the white O-ring featured on t
damaged.
7. Be careful not to get greasy fingerprints or dirt on the lens port. This will affect the image
Be careful not to get greasy fingerprints or dirt on the lens port. This will affect the image
Be careful not to get greasy fingerprints or dirt on the lens port. This will affect the image
quality. Wipe any dirt or grease off with fresh water and a soft cloth.
quality. Wipe any dirt or grease off with fresh water and a soft cloth.
8. Never handle the housing with your ha
Never handle the housing with your hands coated in suntan, oil or cream. Avoid getting
creams or petrol-related substances or liquids on the housing surface, as this can distort and
damage the housing materials.
damage the housing materials.
9. Do not drop the housing on hard surfaces
Do not drop the housing on hard surfaces, it could crack and its watertight seal might be
damaged.
10. Do not disassemble or modify the housing, as this may cause leaks.
Do not disassemble or modify the housing, as this may cause leaks.
11. Do not leave the housing in direct sunlight, inside a car in hot weather, or near a heater. Heat
Do not leave the housing in direct sunlight, inside a car in hot weather, or near a heater. Heat
Do not leave the housing in direct sunlight, inside a car in hot weather, or near a heater. Heat
may warp the housing and cause leaks. If you have to leave the h
p the housing and cause leaks. If you have to leave the housing in the sun, it is
important to cover it with a towel.
important to cover it with a towel.
requires only a minimum amount of care for safe and
in streaming fresh water and if possible soak the housing in
nk for about 20 minutes after every dive in order to dissolve the salt
nk for about 20 minutes after every dive in order to dissolve the salt
in some cases might interfere with the housing watertight seal.
cases might interfere with the housing watertight seal.
cone grease for lubricating the back door black O-ring. Use of any
ring featured on the back side of the front door unless it's
nds coated in suntan, oil or cream. Avoid getting any oils,
related substances or liquids on the housing surface, as this can distort and
related substances or liquids on the housing surface, as this can distort and
If it is dirty, clean it with
before using the housing again.
ring periodically. It's important to note
ring is only enough to allow it to slip into
More grease is not
he back side of the front door unless it's
ousing in the sun, it is
FRX100 VA R Housing Instruction Manual
35
safe and reliable
housing in a fresh
Manipulate each of the
If it is damaged
ring. Use of any
ight seal might be
Instruction Manual 20200225
Hide quick links:
Advertisement
Table of Contents
