Failure Information - Goodwe HT Series User Manual

First level menu
Grid-tie power generation
Long press for 2s
Power = XXXXX watts
Short press
Daily power generation: Long press for 2s
0.0 kWh
Short press
Total power generation:
Long press for 2s
0.0 kWh
Short press
Input voltage:
Long press for 2s
0.0/0.0/0.0/0.0 V
Short press
Input Current:
Long press for 2s
0.0/0.0/0.0/0.0A
Short press
Utility voltage:
Long press for 2s
230/230/230 volts
Short press
Output current (A):
Long press for 2s
0.0/0.0/0.0
Short press to change the number
Short press
Utility frequency: Long press for 2s
0.00 Hz
Short press
Error history
Long press for 2s
Power = XXXXX watts
Short press
GW100K-HT
Long press for 2s
Power = XXXXX watts
Short press
Software version:
V1.XX.XX.XX
Short press
Long press for 2s
Set time
Power = XXXXX watts
Short press
Long press for 2s
Signal strength: 0% W/L restart
Power = XXXXX watts Power = XXXXX watts
Short press
W/L reload Long press for 2s
Power = XXXXX watts
Short press
Power factor adjustment
Long press for 2s
Power = XXXXX watts
Short press
Long press for 2s
Shadow mode OFF Shadow mode ON
Power = XXXXX watts Power = XXXXX watts
Short press Short press
Long press for 2s
Power limit OFF Power limit ON
Power = XXXXX watts Power = XXXXX watts
Short press
Set power limit
XXX%
Short press
Set Modbus address Long press for 2s
Power = XXXXX watts
Long press for 2s
Low voltage ride through ON Low voltage ride through OFF
Power = XXXXX watts Power = XXXXX watts
Short press
Grid type Long press 2s to enter
Power = XXXXX watts
Initial password: 1111
Long press 2s to enter
USB operation mode
25
Second level menu
50Hz grid voltage
Locked
W: 16 S: 0
C: 0
Serial No.:
xxxxxHTUxxxxxxxx
No error
Grid loss
190520 05: 21
Wait
50Hz GridDefault Setting up...
2000-00-00 00:00
Long press for 2s Long press for 2s
Wait
2000-00-00 00:00
Long press for 2s
Wait
······ Setting up...
Long press for 2s
Wait
2000-00-00 00:00
Wi/L restarted successfully
Wait
Wi/L restarting
Wi/L restart failed
Wi/L reload successfully
Wait
Wi/L reloading
Wi/L reload failed
Wait
Unregulated
Short press to select
Short press
"leading" or "lagging"
Wait
Lagging 0.95
Setting up...
Short press to select 8 or 9 Wait
Lagging 0.95
Wait
Lagging 0.95
Wait
Set power limit
XXX%
Long press for 2s
Set power limit Wait
Setting up...
XX%
Long press for 2s
Set power limit Wait
XX%
Long press for 2s
Wait
Set address: XXX
Long press for 2s
Wait
Setting up...
Set address: XXX
Long press for 2s
Wait
Set address: XXX
Long press for 2s
Wait
Star shape
Setting up...
Short press
Wait
Triangle
Wait
Host
Short press Setting up...
Wait
Slave

5.3 Failure Information

The error message in the following table will be displayed on the screen when the abnormal
situation occurs:
Error Message
Internal Communication Failure
EEPROM R/W Failure
Fac Failure
Relay Check Failure
Setting is completed successfully
PV** hardware current over range
Setup failed
DC Injection High
Isolation Failure
Setting is completed successfully
Vac Failure
Setup failed
External Fan Failure
PV Over Voltage
Over Temperature
Internal Fan Failure
DC Bus High
Ground I Failure
Setting is completed successfully
Utility Loss
Setup failed
Reference Voltage Check Failure
GFCI Device Failure
Setting is completed successfully
Setup failed
Setting is completed successfully
Setup failed
Setting is completed successfully
Setup failed
Setting is completed successfully
Setup failed
26