Fault Information - Goodwe GW250K-HT User Manual

Menu
Long press for 2 s
Grid-tied power generation
50 Hz grid voltage
Power = XXXXX watts
Long
Short press
press
Daily power generation:
for 2 s
0.0 kWh
Long
Short press
press
Total power generation:
for 2 s
0.0 kWh
Long
Short press
press
Input voltage:
for 2 s
xxxxxHTUxxxxxxxx
0.0/0.0/0.0/0.0 V
Long
Short press
press
Input Current:
for 2 s
0.0/0.0/0.0/0.0A
Long
Short press press
Utility voltage: for 2 s
230/230/230 volts
Long
Short press
press
Output current (A): for 2 s
50 Hz GridDefault
0.0/0.0/0.0
Long
Short press Short press to change
press
Utility frequency:
for 2 s
2000-00-00 00:00
0.00 Hz
Long
Short press
press
2000-00-00 00:00
Error history
for 2 s
Power = XXXXX watts
Long
Short press press
for 2 s
GW250K-HT
Power = XXXXX watts
2000-00-00
Short press
Software version:
V1.XX.XX.XX
Long
press
Short press
for 2 s
Set time
Short press
Power = XXXXX watts
Long
Short press
press
Power factor adjustment
for 2 s
Power = XXXXX watts
Short press
Long press
for 2 s
Shadow mode OFF Shadow mode ON
Power = XXXXX watts Power = XXXXX watts
Short press Short press
Long press
for 2 s
Power limit OFF Power limit ON
Power = XXXXX watts Power = XXXXX watts
Short press
Set power limit
XXX%
Short press
Set Modbus address Long press for 2 s
Power = XXXXX watts
Long press for 2 s
Low voltage ride through ON Low voltage ride through OFF
Power = XXXXX watts Power = XXXXX watts
Short press
23
Submenu
Locked
W: 16 S: 0
C: 0
Serial No.:
No error
Grid loss
190520 05: 21
Wait
Setting up...
Long press for 2 s Long press for 2 s
Wait
Long press for 2 s
Wait
Setting up...
······
Long press for 2 s
Wait
00:00
Wait
Do not adjust
Short press to select "leading" or "lagging" Wait
Lagging 0.95
Setting up...
Short press to select 8 or 9 Wait
Lagging 0.95
Wait
Lagging 0.95
Wait
Set power limit
XXX%
Long press for 2 s
Set power limit
Wait
Setting up...
XX%
Long press for 2 s
Set power limit Wait
XX%
Long press for 2 s
Wait
Set address: XXX
Long press for 2 s
Wait
Setting up...
Set address: XXX
Long press for 2 s
Wait
Set address: XXX
Long press for 2 s

5.2 Fault Information

When abnormal situation occurs, the following error message may display on the screen:
Error Message
Grid outage
Vac Fail
Fac Fail
Isolation Fail
Setup successfully
GFCI Fail
Setup failed
DCI High
Over Temperature
Setup successfully
Relay Fail
Setup failed
Relay Fail
EEPROM Fail
ExFan Fail
Setup successfully
InFan Fail
Setup failed
Ref-V Chek Fail
DC Bus High
Setup successfully
SPI Comm Fail
Setup failed
Setup successfully
Setup failed
Error Message
GFCI Chk Fail
AC HCT Fail
Gnd I Fail
DC Bus Low
HCT Chk Fail
PV over Curr
PV over Curr
PV soft OverCurr
Model Error
PV Over Voltage
PV Voltage Low
PV HCT Fail
Bus Unbalance
DC Bus High
PV1..PV12 over Curr
24