Lenovo ThinkAgile CP Hardware Part Replacement And Component Maintenance Procedures page 85

Obtain storage controller IP addresses
This section covers the procedure to obtain the storage controller IP addresses.
To obtain the storage controller IP addresses, follow these steps:
Step 1. To obtain the storage controller IP addresses from the Cloud Controller:
a. Navigate to the Organization Viewer topic.
b. Locate the rows of storage controller data.
c. Locate the IP column for the storage controller IP addresses.
Step 2. To obtain the storage controller IP addresses from the CLI:
a. Sign in to the interconnect as in "Access the storage controller using Support Mode" on page
75.
b. Enter the command:
c c a a t t / / v v a a r r / / l l i i b b / / d d h h c c p p / / d d h h c c p p d d . . l l e e a a s s e e s s | | g g r r e e p p s s t t o o r r a a g g e e - - B B 1 1 0 0 | | g g r r e e p p l l e e a a s s e e
IP addresses you can use to sign in to the storage controllers display.
Step 3. To obtain the IP address of the storage controller's Baseboard Management Controller (BMC),
enter the command:
c c a a t t / / v v a a r r / / l l i i b b / / d d h h c c p p / / d d h h c c p p d d . . l l e e a a s s e e s s | | g g r r e e p p A A t t h h e e n n a a - - B B 1 1 0 0 | | g g r r e e p p l l e e a a s s e e
Use these IP addresses to connect to the Web interface using HTTPS.
Transfer the VPD utility to the storage controller
This section covers the procedure to transfer the VPD utility to the storage controller.
To transfer the VPD utility to the storage controller, follow these steps:
Step 1. In the CLI, SSH into one of the storage controllers by entering:
s s s s h h - - I I . . s s s s h h / / c c l l d d t t [ [ tab to get support controller ID] ] c c l l d d t t x x _ _ s s u u p p p p o o r r t t @ @ <Storage IP>
Note: Use one of the storage controller IP addresses from "Obtain storage controller IP
addresses" on page 77.
Step 2. If there is an interconnect switch link, add the following to the command:
- - b b <primary or secondary interconnect IP>
This changes the command to:
s s s s h h - - I I . . s s s s h h / / c c l l d d t t [ [ tab to get support controller ID] ] – – b b <primary or secondary interconnect IP> c c l l d d t t x x _ _
s s u u p p p p o o r r t t @ @ [ [ Storage IP] ]
To check for the switch IP, execute i i p p a a and look for IPs under VLAN 4 or 5. An address ending in 1
will be the primary interconnect switch, while a 2 designates the secondary interconnect switch.
Create a directory named thinkagile_cpsb_vpd_tool on the proxy server to copy the thinkagile_
Step 3.
cpsb_vpd_tool_vX.X.tgz utility bundle from your laptop to the proxy server first.
Once the bundle is copied onto the proxy server, enter the following command to copy the utility to
the storage controller:
s s c c p p t t h h i i n n k k a a g g i i l l e e _ _ c c p p s s b b _ _ v v p p d d _ _ t t o o o o l l c c l l d d t t x x _ _ s s u u p p p p o o r r t t @ @ <storage IP>: : / / h h o o m m e e / / m m a a n n a a g g e e r r / /
.
Chapter 5 Part replacement and maintenance procedures
77