ABB Platinum standard Series Product Instruction page 120

Index
(continued)
R
Reference accuracy ............................... 1-12, 1-15, 1-16
Reference conditions ..................................................1-9
Remote diaphragm seals ..........................................1-17
Repair and replacement
Amplifier assembly
Installation .......................................................8-6
Removal ..........................................................8-6
Bolting
Installation .......................................................8-8
Removal ..........................................................8-8
Cell and characterization board assembly
Installation .......................................................8-5
Removal ..........................................................8-4
Electronics housing and housing cover.................8-7
Equipment required ...............................................8-1
EZ CAL option
Installation .....................................................8-11
Removal ........................................................8-11
Flange adapter installation ..................................8-11
Flange adapter removal ......................................8-11
Indicator
Installation .....................................................8-10
Removal ........................................................8-10
Optional equipment .............................................8-10
O-rings.................................................................8-10
Process flange
Installation .......................................................8-9
Removal ..........................................................8-9
Tagging ...............................................................8-12
Vent/drain plug and pipe plug installation............8-12
Vent/drain plug and pipe plug removal................8-11
Replacement parts ......................................................9-1
Rerange ......................................................................4-6
Reranging the analog output.......................................4-6
Resistance, load limits .....................................3-13, 3-16
Rezero ........................................................................4-6
RFI/EMI effects .........................................................1-10
Secondary engineering units................................5-4, 5-6
Secondary lower and upper range values...................5-4
Select mode ................................................................5-1
SEND CONFIG key.....................................................5-5
Setup and physical installation....................................3-1
Software functions.......................................................2-7
Spare parts lists ..........................................................9-1
SPECIAL FEATURE key.............................................5-5
Specifications ........................................... 1-9, 1-11, 1-14
Common................................................................1-9
Damping ........................................................1-10
Index - 4
S
Enclosure rating ............................................ 1-10
Humidity limits ............................................... 1-10
Loop load limits ............................................. 1-10
Output current limiting ................................... 1-10
Output signal ................................................. 1-10
Power supply effect....................................... 1-10
Reference conditions ...................................... 1-9
RFI/EMI effects ............................................. 1-10
Supply voltage............................................... 1-10
Surge tolerance............................................. 1-10
Temperature limits ........................................ 1-10
Vibration effect .............................................. 1-10
PTSDA
Measurement Range..................................... 1-16
Pressure limits............................................... 1-16
Reference accuracy ...................................... 1-16
Stability.......................................................... 1-16
Temperature effect........................................ 1-16
Turndown ratio .............................................. 1-16
Weight ........................................................... 1-16
Zero elevation ............................................... 1-16
Zero suppression .......................................... 1-16
PTSDD................................................................ 1-11
Measurement Range..................................... 1-11
Pressure limits............................................... 1-13
Reference accuracy ...................................... 1-12
Stability.......................................................... 1-12
Static pressure effect .................................... 1-13
Temperature effect........................................ 1-13
Turndown ratio .............................................. 1-11
Weight ........................................................... 1-13
Zero elevation ............................................... 1-11
Zero suppression .......................................... 1-11
PTSDG ............................................................... 1-14
Measurement Range..................................... 1-14
Pressure limits............................................... 1-15
Reference accuracy ...................................... 1-15
Stability.......................................................... 1-15
Temperature effect........................................ 1-15
Turndown ratio .............................................. 1-14
Weight ........................................................... 1-15
Zero elevation ............................................... 1-14
Zero suppression .......................................... 1-14
Spherical tank volume calculation .............................. 2-7
Stability ...................................................1-12, 1-15, 1-16
Standard configuration ............................................... 5-5
Startup and failure conditions ..................................... 5-3
Static pressure
Effect................................................................... 1-13
STATUS key ............................................................... 5-6
STT........................................................................... 3-16
Configuration procedure ....................................... 5-1
WBPEEUI110504A0