Subscribe to Our Youtube Channel
Related Manuals for Teldat K Seres
Summary of Contents for Teldat K Seres
- Page 1 Manual Teldat S.A. Teldat K/KF router Installation Manual Copyright© Teldat-DM540-I Version 5.1 7/2015 Teldat S.A. Teldat K/KF router...
- Page 2 This publication is subject to change. Teldat S.A. offers no warranty whatsoever for information contained in this manual. Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv- ery, supply or use of this manual.
-
Page 3: Table Of Contents
Chapter 2 Teldat K / Teldat KF Routers ......4 Features........ - Page 4 CE Marking ........Teldat K/KF router...
- Page 5 B.3.6 Technical Documents on http://www.teldat.com ..... . Standards Compliance ....... .
- Page 6 Table of Contents Teldat S.A. Teldat K/KF router...
-
Page 7: I Related Documents
Related Documents Teldat S.A. I Related Documents Teldat-Dm 748-I Software Updating Teldat K/KF router... -
Page 8: About This Manual
1 About This Manual Teldat S.A. Chapter 1 About This Manual This is the installation manual for the Teldat K router family and contains information on how to correctly install this device in a working environment. 1.1 Supported Devices The information provided only applies to the Teldat K router family. - Page 9 1 About This Manual Teldat S.A. Tel.: +34 918 076 565 Fax: +34 918 076 566 Email: support@teldat.com Teldat K/KF router...
-
Page 10: Teldat K / Teldat Kf Routers
2.1.2 Hardware Monitoring The only way to monitor the Teldat K router family hardware is through the LEDs panel. The LEDs provide visual in- formation on what is happening in the device. They indicate the state of the hardware components, if there is con- nectivity, data flow, etc. -
Page 11: Components And Power Supply
Auxiliary antenna 2 for the Teldat K cellular module. Auxiliary antenna 1 for the Teldat K cellular module. 3.1.2 Rear Panel The following figure shows the rear panel. Here you can see all the connectors for the Teldat K router family. Rear panel Fig. 2:... -
Page 12: Side Panels
Two WiFi antennas are located on the side panels, one on either side. Right hand side panel Left hand side panel Fig. 3: and Fig. 4 3.1.4 Underside Panel The following elements can be found on the underside panel: Teldat K/KF router... -
Page 13: Top Panel (Leds)
Underside panel elements table Item Description SIM tray for the internal module. This is only found on the Teldat K. It’s accessed from the underside of the router. Platform where the label containing the information on the product is placed. This label contains information on the device model, mac, serial number, etc. - Page 14 3 Components and Power Supply Teldat S.A. Leds panel Fig. 6: The LEDs for the Teldat K router family are shown in the above figure. The table below contains a description on them. LEDs table Status Description Monochrome Green Off -> not being powered through PoE.
-
Page 15: Mounting In Rack
3.2.2 Wall mounting The Teldat K can be mounted on the wall. The Teldat KF can be as well, but this doesn’t make much sense as it doesn’t have a 3G module incorporated. There are two slots on the underside of the device which are used to fix it to the wall. You can see this in section “Underside Panel... - Page 16 Wall-Mounting Features on the Teldat K/KF router Fig. 7: Figure 7 shows the wall-mounting features on the Teldat K/KF routers. Wall screws 10.2 cm (4.02 inches) Chassis mounting holes (on...
-
Page 17: Plug-In Modules
Fig. 8 on page 11. 3.4 Power Source The Teldat K router family is powered though an external AC/DC source or through an Ethernet cable (if it complies with the POE 802.3at standard). Warning The equipment must be used with the power supply provided by the manufacturer, or equivalent. -
Page 18: External Power Source
3.4.2 PoE The Teldat K router family can be powered through an Ethernet cable if the latter complies with the POE 802.3at standard. The port enabled for this is the Eth WAN. To connect the Ethernet cable with PoE power to the router, please carry out the steps outlined in section “... -
Page 19: Disconnect
• With the device switched off, keep the RST button pressed and switch on the router through the ON/OFF switch (1). • The PSU LED (green) will light up and the Alert LED will begin to blink (amber). This blinking will continue for 10 seconds. Teldat K/KF router... -
Page 20: Cargalan Mode
The Teldat K router family has the following data connections. 3.6.1 4-port Ethernet Switch The Teldat K router family incorporates a 4-port 10/100/1000 BaseT Switch with automatic MDI/MDIX to connect to a local area network (LAN). Please pay careful attention to the labeling so you do not confuse this switch with other types of ports: LAN switch PORTs Fig. -
Page 21: Wan Connection
The Teldat K router family incorporates an Ethernet WAN 10/100/1000 BaseT port with automatic MDI/MDIX. The WAN port is independent from the switch and is managed like any other interface. The Teldat K has a special li- cense, the 1GELAN, that deactivates the switch. When doing this, the WAN connection becomes the LAN and its in- terface, which was previously the switch interface, becomes the Ethernet0/0. -
Page 22: Wireless Lan Antenna Connection (Wi-Fi Connectors)
3.6.4 Wireless LAN Antenna Connection (Wi-Fi connectors) The Teldat K router family has three RF antenna connectors for external antennas in order to improve the quality of the signal received and transmitted by the Wireless LAN module. -
Page 23: Connecting A 3G Usb Device (Usb Connector)
3.7 Installing the SIM card The Teldat K family has a Wireless WAN interface, which means that at least one SIM card must be inserted in the device for it to work. There are certain services (CDMA) provided by several carriers in some countries that do not require SIM cards. - Page 24 Teldat S.A. The other SIM tray belongs to the internal 3G module, only available in the Teldat K. To access it, you need to go to the underside of the router and open the flap that is shown in the following figure to insert the SIM card.
-
Page 25: Appendix A Technical Information
The connection is carried out through the Switch, which has the Ethernet0/0 interface. If the router is a Teldat K with a 1-GE-LAN license, then the connection is via the WAN as the LAN will be inactive and the WAN becomes the Ethernet0/0. -
Page 26: Licenses
Basic: 4xGE. Optional: WiFi, USB, hardware encryption, 1xGE-WAN, 1xGE-LAN (disables 4xGE switch). Below, you can find the information on the optional licenses for each router in the Teldat K family. WiFi: Activation license for the WLAN 802.11bgn. USB: Activation license for the USB port to be used for the WWAN modems. -
Page 27: Wwan Connector (Female)
A.5.5 USB Connector USB Type A DATA- DATA+ Shell Shield A.5.6 Power Supply Connector Internal POSITIVE External NEGATIVE A.6 Technical Specifications A.6.1 Hardware Architecture PROCESSORS Freescale QorQ MEMORY 128 Mbytes in SDRAM STORAGE UNIT FLASH Memory (32 Mbytes) Teldat K/KF router... -
Page 28: Lan Interface
3 RF SMA Female A.6.6 USB Interface 3G USB MODEMS Please see the Teldat website http://www.teldat.com to get a list of the supported 3G USB modems. SPEED The interface complies with the USB 2.0 (480 Mbps) standard; the end speed de- pends on the 3G USB modem used. -
Page 29: Configuration Interface
LENGTH x WIDTH x HEIGHT 242 x 179 x 48 mm WEIGHT 0.8 kg A.6.11 Environmental Specifications TEMPERATURE OPERATING NORMALLY: 0 °C to 45 °C STORED: -30 °C to 85 °C RELATIVE HUMIDITY On: 5 % to 90 % Teldat K/KF router... -
Page 30: Appendix B Regulatory Compliance And Safety Information
B.1 Recycling and the Environment Please do not, under any circumstances, throw away any Teldat K/KF with normal domestic waste. Ask your local town hall for information on how to correctly dispose of them in order to protect the environment against e-waste. Al- ways respect the current laws regarding waste material. -
Page 31: Translated Safety Warnings
Regulatory compliance and safety information Teldat S.A. B.2 Translated Safety Warnings Connecting Disconnect Teldat K/KF router... -
Page 32: Declaration Of Conformity
Teldat S.A. B.3 Declaration of Conformity Compliance Information for the Teldat K/KF routers relevant to the European Union and other countries following the EU Directive 1999/5/EC (R&TTE Directive) This section contains compliance information for Teldat K/KFrouters. This information is relevant to the European Union and other countries that are following the EU Directive1999/5/EC. -
Page 33: Declaration Of Conformity With Regard To The Eu Directive 1999/5/Ed (R&Tte Directive)
Regulatory compliance and safety information Teldat S.A. B.3.1 Declaration of Conformity with regard to the EU Directive 1999/5/ED (R&TTE Directive) Teldat K/KF router... -
Page 34: Counties Where The Equipment Is Intended To Be Used
B.3.2 Counties where the equipment is intended to be used B.3.3 CE Marking For the Teldat K/KF, the following CE mark and class 2 identifier are added to the equipment. B.3.3.1 Standards The following standards were applied during the assessment of the product against the requirements of the Directive... - Page 35 Later in this paragraph you will find an overview of countries in which additional restrictions and/or requirements are applicable. The requirements for any country may evolve. Teldat recommends that you check with the local authorities for the latest status of their national regulations for 2.4 and 5 GHz wireless LANs.
- Page 36 The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm). B.3.4 Product Usage Restrictions This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted. Teldat K/KF router...
- Page 37 This product is designed to be used with the antennas defined by the manufacturer. B.3.5 Third Party Software or Firmware The use of software or firmware not supported/provided by Teldat may result in the equipment no longer being com- pliant with the regulatory requirements.
- Page 38 Operation of this equipment in a residential area is likely to cause harmful inter- ference, in which case the user will be required to correct the interference at his own expense. Teldat K/KF router...
Need help?
Do you have a question about the K Seres and is the answer not in the manual?
Questions and answers