Krick Klemm L25-D Assembly Instructions Manual page 33

4.16 The engine mount is put together from the five parts R-35 and glued into the grooves of the engine
bulkhead. Its length makes it possible to fit standard, 1930s-class external rotors.
4.17 Attach the engine hood and align it according to the engine shaft. Then screw it onto the left and right
sides of the fuselage sing two screws on each side.
4.18 Stick two magnets on each side of the middle section of the wing. Make sure that they are stuck onto
the wings with the correct polarity. You can also place the magnets onto the wing with film in between,
then apply adhesive and attach the whole thing to the fuselage. This ensures a perfect fit and secure
hold.
5. Outer parts of the wing
No. Designation
TF-01 Main panelling, bottom front
TF-01u Main panelling, rear bottom
TF-01o Main panelling, rear top
TF-02u Trailing edge panelling, inside bot. 2
TF-02o Trailing edge panelling, inside top
TF-03u Trailing edge panelling, outside bot. 2
TF-03o Trailing edge panelling, outside top 2
TF-04 Root panelling, two pieces
TF-05 Rib panelling
TF-06 Rib panelling
TF-07 Rib panelling
TF-08u Rib panelling, top
TF-08o Rib panelling, bottom
TF-09 Rib panelling
TF-10 Rib panelling
TF-11 Rib panelling
TF-12 Rib panelling
TF-13 Rib panelling
TF-14 Rib panelling
TF-15u Rib panelling, top
TF-15o Rib panelling, top
TF-16 Main spar
TF-17 Root rib
TF-18 Wing rib
TF-19 Wing rib
TF-20 Wing rib
TF-21 Wing rib
TF-22 Wing rib
TF-23 Wing rib
TF-24 Wing rib
TF-25 Wing rib
TF-26 Wing rib
TF-27 Wing rib
TF-28 Wing rib
TF-29 Wing rib
TF-30 Shear webbing plug-in mount,
bottom section
TF-31 Shear webbing plug-in mount,
top section
TF-32 Shear webbing
TF-33 Shear webbing
TF-34 Shear webbing
TF-35 Shear webbing
TF-36 Shear webbing
TF-37 Shear webbing
TF-38 Shear webbing
TF-39 Shear webbing
TF-40 Shear webbing
TF-41 Shear webbing
TF-42 Trailing edge
TF-43 Nose board
TF-44 Corner reinforcement
TF-45 Root rib doubler magnet, front
Quantity Material
4 Balsa
2 Balsa
2 Balsa
Balsa
2 Balsa
Balsa
Balsa
4 Balsa
4 Balsa
4 Balsa
4 Balsa
2 Balsa
2 Balsa
4 Balsa
4 Balsa
4 Balsa
4 Balsa
4 Balsa
4 Balsa
2 Balsa
2 Balsa
4 Pine
2 Birch
2 Birch
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
2 Poplar
Dimensions Comments/plate
1.5 mm Laser-cut part 15
1.5 mm Laser-cut part 13/14
1.5 mm Laser-cut part 12
1.5mm Laser-cut part 15
1.5 mm Laser-cut part 8/9
1.5 mm Laser-cut part 15
1.5 mm Laser-cut part 11
1.5 mm Laser-cut part 18
1.5 mm Laser-cut part 13
1.5 mm Laser-cut part 14
1.5 mm Laser-cut part 14
1.5 mm Laser-cut part 9
1.5 mm Laser-cut part 8
1.5 mm Laser-cut part 13
1.5 mm Laser-cut part 14
1.5 mm Laser-cut part 13
1.5 mm Laser-cut part 14
1.5 mm Laser-cut part 13
1.5 mm Laser-cut part 13
1.5 mm Laser-cut part 13
1.5 mm Laser-cut part 13
3 x 10 x 775 mm Square strip
3 mm Laser-cut part 6
3 mm Laser-cut part 6
3 mm Laser-cut part 1
3 mm Laser-cut part 2
3 mm Laser-cut part 1
3 mm Laser-cut part 2
3 mm Laser-cut part 1/2
3 mm Laser-cut part 1/2
3 mm Laser-cut part 1/3
3 mm Laser-cut part 1/2
3 mm Laser-cut part 2
3 mm Laser-cut part 2
3 mm Laser-cut part 1
3 mm Laser-cut part 4
3 mm Laser-cut part 4
3 mm Laser-cut part 3
3 mm Laser-cut part 3/4
3 mm Laser-cut part 2/4
3 mm Laser-cut part 1/4
3 mm Laser-cut part 3
3 mm Laser-cut part 3
3 mm Laser-cut part 1/2
3 mm Laser-cut part 2
3 mm Laser-cut part 1
3 mm Laser-cut part 1
3 mm Laser-cut part 4
3 mm Laser-cut part 4
3 mm Laser-cut part 1/2
3 mm Laser-cut part 1/2