Related Manuals for Nice Pro-H
Summary of Contents for Nice Pro-H
- Page 1 Pro-H Automation for sectional and rolling doors EN - Instructions and warnings for installation and use...
- Page 2 NICE CANADA warrants that materials and workmanship are free from defects for a period of two years from the date of invoice. Materials returned to Nice deemed defective after examination will be returned at the option of Nice with repaired, new or re-manufactured parts.
- Page 3 C NTENTS ANTY E I ICATI N E AT S ECI ICATI NS SA ETY INST CTI NS INSTA ATI N E ECT ICA C NNECTI NS AN SETTIN S IMIT S ITC STMENT INSTA ATI N INST CTI NS ___________ STMENT STMENT...
- Page 4 CTI NS E I ICATI N E AT pon delivery of your Nice heavy-duty ackshaft door operator, please inspect the unit carefully for damage. erify that operator control wiring option, , voltage, phase and amperage correspond to available power supply and door application.
- Page 5 I IN TY E TI NS ption ull eature logic board Smart compliant . Note Nice compatible primary entrapment device must be connected for , T or TS momentary or timer activation on close feature. ption elay logic controls with Interface Module compliant .
- Page 6 TANT SA ETY INST CTI NS A NIN CE T E IS EA AN INST CTI NS Never allow children to operate or play with door controls. eep the remote control where provided away from children. ersonnel should keep away from a door in motion and keep the moving door in sight until it is completely closed or opened.
- Page 7 INSTA ATI N INST CTI NS A NIN N T INSTA T IS E AT E EA IN T IS MAN A CA E Note Installation of operator must be done by a ualified installer. oor must be properly installed and working smoothly.
- Page 8 As a general rule, the door operator should be installed below the drive shaft and as close to the door as possible. The ideal distance between the operator drive shaft and the door shaft is approximately cm to cm . The operator may be wall bench mounted or bracket shelf mounted.
- Page 9 - models Install hand chain by wrapping it through chain guard holes and pocket wheel. Allow chain to hang down towards floor. Cut chain and connect so that chain is from the floor. Install chain keeper to wall near hand chain at approximately from floor.
- Page 10 A C MME CIA E AT M ST A E IT S E ICATE NICE I Y EC MMEN S T AT EAC IN I I A C MME CIA E AT A E AN E TE NA CI C IT...
- Page 11 SECTI N A PRO- PRO-H tandard rela logic controls (not ) compliant not a ailable in C NNECTI N Y AN C NT STATI N I IN se - cm diameter holes for all power wiring. . Single phase Connect single phase power supply to terminals...
- Page 12 C NNECTI N A E E SIN E E E ICE AN C NT ACCESS eversing Edge device must be normally open contact Note If the door is controlled by any device or wired in such a manner that the door is not controlled by constant pressure on close then an appropriate reversing edge must be installed.
- Page 13 NOTE: THIS OPERATOR COMES WITH AN INTERFACE MOUDLE INTEGRATED INTO THE CONTROL CIRCUIT. THE PURPOSE OF THE INTERFACE MODULE IS TO ALLOW FOR FAILSAFE MONITORING OF A NICE COMPATIBLE SAFETY DEVICE AS PER UL 325 (2010) REQUIREMENTS Important ollow these steps carefully and in the order shown...
- Page 14 ingle phase operators The operators leave the factory with correct motor and limit shaft direction according to standard door installations. owever, for special fire door, thru- wall mounting or other special door applications, the motor direction and limit switch direction may need to be reversed. To reverse the motor rotation, interchange black and white wires going to motor on the reversing contactor.
- Page 15 . Primar monitored safet de ice Nice monitored failsafe photo beams or Nice compatible monitored failsafe devices must be connected to terminals if momentary close on pushbutton is re uired mode .
- Page 16 SECTI N C PRO- ( ) PRO-H( ) ull feature logic board mart ) compliant) Note The operator is shipped from the factory in the mode setting constant pressure open and close . The operator should remain in this mode until all connections and limit switch ad ustments are completed.
- Page 17 . rimary monitored safety device Nice monitored failsafe photo beams or Nice compatible monitored failsafe devices must be connected to terminals as primary monitored safety device. rimary monitored safety device must be connected if momentary activation on close is re uired in , T and TS modes.
- Page 18 Secondary non-monitored safety device s A standard -wire safety edge, non-monitored photo beams or any other non-monitored reversing devices with a N. contact can be connected to terminals S and S as secondary non-monitored safety device. Note More than one secondary non-monitored safety device can be connected to terminals S and S . Important o not remove the resistor that is factory installed across terminals S and S unless installing a -wire electric edge.
- Page 19 Momentary open, constant pressure close • pen utton Momentary activation opens the door. hen door is closing, momentary activation reverses the door I E . Momentary contact from mid-stop opens the door to full open position. Constant activation when door is opening, bypass mid-stop if enabled. •...
- Page 20 • Timer to close Closes the door from mid-stop or full open. Momentary activation of stop button will de-activate the timer. hen door is closing, momentary activation of safety devices will reverse the door to mid-stop if enabled or full open and de-activates the timer.
- Page 21 , activation of close button will delay to T amount of time. ECEI E AMMIN This logic board has a built-in radio receiver and can only be used with Nice single button, -button EN C SE ST and -channel radio transmitters. INSTA IN T E ANTENNA...
- Page 22 Note If an external radio-receiver Nice or other is used instead of the built-in radio receiver, it is highly recommended to disconnect the co-axial cable from the logic board.
- Page 23 Nice recommends . sec reverse is . seconds is . seconds delay on reverse for all applications Standard motor...
- Page 24 SECTI N or all operator control types IMIT S ITC A STMENT Ad ustment of door travel is done by moving the limit cams on the threaded shaft. The position of the limit switches are factory ad usted and should not be altered. The limit switches are pen limit switch End of door travel in the fully open position - Closed limit switch End of door travel in the fully closed position - Advanced pen or Auxiliary advanced closed limit switch...
- Page 25 NEMA infrared photo systems are for use only with Nice logic board operators or relay logic operators e uipped with the Nice failsafe interface module. se of this device on other than recommended operators can lead to severe or fatal in ury. ollow these instructions carefully.
- Page 26 - Connect these paired wires to the terminals on the logic board or interface module if applicable as shown in igure . NICE N- T CE he M photocell s stem has a ma imum range of...
- Page 27 Nice photo beams must be connected for the door to close in momentary mode unless a Nice monitored wire edge is connected . hen the photo system is properly installed and aligned, the infrared beam will detect any obstruction in the path of the beam.
- Page 28 A A N- - EAM T CE he M photocell s stem has a ma imum range of un isor protector optional Select a location on the wall no more than inches from the floor to install wall mounting brackets on the left and right side of the door.
- Page 29 TC A STMENT emove cotter pin tapped to pulley. otate clutch nut counterclockwise loosen until there is insufficient tension to permit clutch to drive door. radually tighten clutch nut until the tension on belleville washers is sufficient to permit clutch to drive door smoothly but will allow clutch to slip if door is obstructed.
- Page 30 ENCY MAN A E ATI N - and - operators are e uipped with an emergency disconnect device with interlocked power cut-out switch to manually operate door in case of emergency. This feature should not be used to manually operate a malfunctioning door. A NIN CE T E IS N T ATTEM T T...
- Page 31 E AT MAINTENANCE A NIN CE T E IS N T ATTEM T T SE ICE T E E AT N ESS Y AS EEN ISC NNECTE Inspect manual function of the door every -months. Make sure that door runs smoothly. If door does not manually open or close freely, have a ualified service person make repairs.
- Page 44 HEADQUARTERS HEAD OFFICE CHICAGO ATLANTA PHOENIX Nice Canada Nice S.p.A. 1380 St-Regis 721 W. Racquet Club Dr. 2885 N. Berkeley Lake Rd. 1236 W. Southern Ave. Oderzo, TV Italy 31046 Dorval, QC Canada Addison, IL USA Suite 7, Duluth, GA USA...