Operating Instructions; Functions; Lcd Functions; Button Functions - Mitsubishi Electric Super-S ME96SS Series Manual

Operating Instructions

Functions

‡
»LCD Functions
1
3
4
7
8
9
13 14 15 16
»Button Functions
Basic functions
Button
Set up setting items such as primary voltage and
SET
current, and choose and indicate setting itmes
Change setting and bar graph display
or
Change display from Max/Min to instantaneous value
MAX/MIN
PHASE Change phase
Change display
DISPLAY
Set-up
‡
For correct measurement, it is necessary to set the primary voltage/current in set-up mode.
Access set-up mode from the measurement mode and set the necessary items. Factory default settings will apply to items not set.
»Set-up workflow (in the case of ME96SSHA-MB)
Set-up menu End Set-up menu 1 Set-up menu 2
End display
Phase/ Wire
Display
pattern
Using VT/
MODBUS
Cancel
direct input
address
display
MODBUS
CT current
baud rate
MODBUS
Frequency
parity
Change/
Confirm
values set
Rolling demand MODBUS
Measurement screen
stop bit
time limit
Enter
set-up
Demand current
mode
time limit
Enter setting value
confirmation mode
Notes 1. Basic measurements are possible by adjusting settings in menu 1
( area enclosed by dotted line).
Notes 2. Item settings vary depending on the model.
Notes 3. Setting confirmation menu 9 (test mode) is not displayed in the setting mode.
No.
1 Lead Status
2 Lag status
2
3 Scale of the bar graph
4 Excessively low input
5 Excessively high input
6 Upper/lower limit alarm indicator
3
7 Bar graph status
5 8
Phase status
9 Digital
6
10 Unit
11 Metering status
12 Harmonics
10
13 Setup status
14
Test status
15 Clock status
11
16 Upper/lower limit alarm status
17 Communication status
17 12
Functions
Set-up menu 3
Current scale
Communication
Voltage scale
CC-Link MODBUS ® TCP
® RTU
Power scale
station No IP address
RTU CC-Link MODBUS TCP Reactive
® ®
baud rate sub-net mask power scale
Use/non-use of
® RTU CC-Link
Power factor
MODBUS TCP
®
version setting
default gateway
® RTU CC-Link MODBUS ® TCP Power used
reset default gateway scale
Harmonic
Communication
<When ME-0040C-SS95 is installed>
reset display
<When ME-0000MT-SS96 is installed>
Segment name
Power factor status is lead
Power factor status is lag
The scale of the bar graph
On when the measurement value is lower than the minimum scale value
On when the measurement value is higher than the maximum scale value
Flashing when the upper and lower limit alarm values have been set
The item expressed with the bar graph
The phase for each of the digital displays
The measured value is displayed in a digital number
The unit for each of the digital display
When it is blinking, the instrument is counting active energy
On when harmonics values are displayed
is on in the test mode.
is flashing in the set value check mode.
On in the test mode
When it is blinking, the instrument is counting operating time
Flashing when upper/lower limit alarm has occurred
On in normal state, and flashing or off in abnormal state
Special functions
Button
Push for 2s
DISPLAY
Push for 2s
PHASE
+ Push for 2s
+ Push for 2s
RESET
or Push for 1s
+ +
SET RESET PHASE
Set-up menu 4 Set-up menu 5 Set-up menu 6
Upper/Lower
Function Selection
limit alarm
display of options
items
Upper/Lower
Version
limit alarm
display
values
Analog
output 1
Backlight Alarm mask
brightness time
Analog
output 2
Backlight
Alarm reset
connection/
method
automatic
Analog
output 3
Display Backlight of
refresh time alarm
Analog
output 4
Motor starting
current mask
function
Output
limit
Pulse/Alarm
output function
<When ME-4210-SS96 is installed>
Pulse output
Symbol
Description
Functions
Manual display change < = > Cyclic display change
Manual phase change < = > Cyclic phase change
Zoom display of Wh, varh etc
Reset all the Max/Min values
Fast forward or fast return values when setting
Reset Wh, varh, Vah values to zero by
holding down the buttons for 2 sec
Set-up menu 7 Set-up menu 8
Time-based
Operating time
power used
display
display
Time-based
Operating time
power used
count target
toggle setting
Logging ID
Rolling
Operating time
demand
threshold value
display
Logging data
clearing
Rolling demand
Phase display
time limit
setting
adjustment setting
Logging
element
pattern
Contact IEC mode
display setting
Detailed data
logging
interval
Contact input
reset method
<When ME-0000BU-SS96 is installed>
Operation (function) details Button operation
SET +
Access set-up mode from operating mode RESET Simultaneously press for 2s
Access setting value confirmation
SET
mode from operating mode
SET
Save settings and return to operating mode
Select set-up menu
Move to next screen SET
Return to previous setting item DISPLAY
SET
Skip remaining settings
Select cancel
Setting value confirmation menu 9
Test mode
Press for 2s
or
Press for 1s
or
14