Analog Output Setting - Mitsubishi Electric Super-S ME96SS Series Manual

uSelect with or without harmonic display.
uHarmonic display
SET
When the display is set to "on," the harmonic value measured will be
displayed on an additional screen.
Select another set-up menu or end set-up
Set-up menu
‡To continue to set-up
Select the menu
No. using the
Set-up menu 6: Analog output setting
* Only in the case of ME96SSHA-MB or ME96SSRA-MB, it is applicable.
This menu will not appear if ME-4210-SS96 (optional) is not installed.
Adjust the set-up menu No. to "6".
Set-up menu
qSet the output items for "analog output CH1".
Select the measured items to be output from the table below.
When 3-phase 4-wire system has been selected
DISPLAY SET
non
A
1
A
2
A
3
A
N
qAnalog output CH1
A
AVG
output items
Demand A
Demand A
Demand A
Demand A
Demand A
V
DISPLAY SET 1N
V
2N
V
3N
V
AVG
wAnalog output CH1
wSet the details for "analog output CH1."
detailed settings
(The following settings can be made separately from the measurement items included in the display pattern.)
(1) If analog output is selected for current, demand current, voltage,
power, reactive power, power factor (set-up menu: 6.1.1)
Output item
Demand A
var
DISPLAY SET
PF
(2) If analog output is selected for current, demand current, power
(set-up menu: 6.1.2)
Output item
Demand A
oFF on
(without) (with)
or button.
(only when ME-4210-SS96 is installed)
Three phase 4-wire
V PF
12
V PF
23
V PF
31
V (L-L) PF
AVG
W Hz
1
(CH1) W Harmonic A
2
W Harmonic A
1 3
W (CH3) Harmonic A
Σ
2
var Harmonic A
3 1
var Harmonic V
N 2
var Harmonic V
AVG 3
var Harmonic V
Σ
VA
1
VA
2
(L-N) (CH2) VA
3
VA
Σ
AVG: Average value, Σ: Total effective value
Setting range
CT primary current value (value set for set-up menu 1.4.1 primary current setting )
A
SP. (special primary current value)
+10 steps (approx. 250%)
±0 steps (100%: standard max. scale value)
V
−18 steps (approx. 20%)
+3 steps (approx. 120%)
W
±0 steps (100%: instrument rating)
−18 steps (approx. 20%)
−0.5~1~0.5
Setting range
+3 steps (approx. 120%)
A
±0 steps (100%: instrument rating)
−10 steps (approx. 40%)
Positive-only Positive/Negative
W
‡To finish set-up
Press the or button
to display the End screen,
then press the button
SET
to save settings.
1
2
3
(CH4)
Σ
1
2
3
N
Notes 1. The same measurement items can be set for all channels.
1N
Notes 2. Measurement items not included in the selected display pattern can also be chosen.
2N Notes 3. Channels set to "non" will have minimum output (4mA). Additionally, set-up will proceed to the
next channel.
3N
Notes 4. Underlined specifications are factory default settings of measurement items allocated to each
channel.
Notes 5. Harmonic current is output at the scale of 0~60% (with respect to rated value) of the total
effective value. Harmonic voltage is output at the scale of 0~20% of the total distortion ratio.
mA
20
12
−0~1~0
4
−
0.5 1 0.5
<Positive-only>
mA
20
4
0
40kW
u
q
w(1)
DISPLAY
w(2)
mA
20
12
4
−
0 1 0
<Positive/Negative>
mA
20
DISPLAY
12
4
−
40kW 0 40kW
To next channel settings
SET
SET
20