Chapter 5: Operations Page - Watlow Integrated Controller User Manual Rev C EZ-ZONE PM User Manual

5

Chapter 5: Operations Page

To go to the Operations Page from the Home Page,
press both the Up ¿ and Down ¯ keys for three sec-
onds. [``Ai] will appear in the upper display and
[oPEr] will appear in the lower display.
• Press the Up ¿ or Down ¯ key to move through
the menus.
• Press the Advance Key ‰ to move to a submenu.
• Press the Up ¿ or Down ¯ key to move through
the submenus.
Home
Page Operations Page Parameters
[~~p~] [``Ai] [~~~I]
ˆ ˆ ˆ
[~~Sp] [oPEr] [``Ai] [`ain]
<> ‰ ‰
Hold both keys
Analog Input 1 Process
for 3 seconds.
Input Menu Value
Submenu
<
<
> >
ˆ Input 2 Same as above.
Submenu
ˆ
[`diO] [~~~5]
ˆ ˆ
[oPEr] [`diO] [`do; S ]
‰ ‰
Digital In- Digital I/O 5 Output State Event Input
put/Output
Submenu
Menu
<
>
<
>
ˆ Digital I/O 6 Same as above.
Submenu
ˆ
[LiM]
ˆ
[oPEr] [`LL; S ] [`Lh; S ]
‰ ‰
Limit Limit Low Limit High
Menu Set Point Set Point
<
>
ˆ
[Mon]
ˆ
[oPEr] [C; M A] [`h; P r]
‰ ‰
Monitor Control Heat Power
Menu Mode Active
<
>
ˆ
[Loop]
ˆ
[oPEr] [`r; E n] [`r; t Y]
‰ ‰
Loop Menu Remote Remote Set
Enable Point Type
<
>
ˆ [ALM] [~~~I]
ˆ ˆ
[oPEr] [ALM] [`A; L o]
‰ ‰
Alarm Alarm 1 Alarm Low
Menu Set Point
Submenu
<
<
> >
ˆ Alarm 2 to 4 Same as above.
Submenus
ˆ [CUrr]
ˆ
[oPEr] [`C; h i] [`C; L o]
‰ ‰
Current Current High Current Low
Menu Set Point Set Point
<
>
[P; S tA]
ˆ
ˆ
[oPEr] [P; S tr] [P; A Cr]
‰ ‰
Profi le Profi le Start Profi le
Status Action
Menu Request
<
>
®
Watl o w EZ-ZO N E PM In t eg r a te d Co n t r o lle r
[`i; E r] [`i; C a]
‰ ‰ ‰
Input Error Input
Status Calibration
Offset
[`Ei; S ]
‰ ‰
Status
‰
[`C; P r] [`C; S P] [`Pu; A ]
‰ ‰ ‰ ‰
Cool Power Closed Loop Process
Working Set Value Active
Point
[`C; M ] [A; t SP] [`AUt] [`C; S P]
‰ ‰ ‰ ‰
Control Autotune Autotune Closed Loop
Mode Set Point Request Set Point
[`A; h i]
‰ ‰
Alarm High
Set Point
[`CU; r ] [`C; E r] [`h; e r]
‰ ‰ ‰ ‰
Current Read Current Error Heater Error
[`Stp] [S; t YP] [tg; S P] [AC; S P]
‰ ‰ ‰ ‰
Active Step Active Step Active Target Active Set
Type Set Point Point
• Press the Advance Key ‰ to move through the pa-
rameters of the menu or submenu.
• Press the Infinity Key ˆ to move backwards
through the levels: parameter to submenu; sub-
menu to menu; menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds
to return to the Home Page.
Note: Avoid continuous writes within loops. Excessive writes to
EEPROM will cause premature EEPROM failure. The EEPROM is
rated for 1,000,000 writes.
Navigating the Operations Page
Note:
Some of these menus and parameters may not appear, depending
on the controller's options. See model number information in the
Appendix for more information.
If there is only one instance of a menu, no submenus will appear.
[`id; S ] [`h; P b] [`h; h Y]
‰ ‰ ‰ ‰
Idle Set Heat Propor- Heat Hyster-
Point tional Band esis
[`S; t i] [Ent1] [``JC]
‰ ‰ ‰ ‰
Step Time Active Event Jump Count
Remaining Output Remaining
(1 or 2)
28
• •
[`C; P b] [`C; h y] [``ti] [``td]
‰ ‰ ‰
Cool Propor- Cool Hyster- Time Integral Time Deriva-
tional Band esis tive
Chapter 5 Operatio ns Page
[``db] [`o; S P]
‰ ‰ ‰
Dead Band Open Loop
Set Point