ES0152 / ES0152P CLI User Manual EMC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Overview Chapter 1, Introduction, introduces you the release version, purpose, and audience for ES0152 / ES0152P CLI user guide. Chapter 2, CLI Management, provides step-by-step instructions for CLI management, including login, commands of CLI, and global commands of CLI.
Page 11
ES0152 / ES0152P CLI User Manual Chapter 15, IPV6 Commands of CLI, shows a description, syntax, parameter, and example for IPV6 commands. Chapter 16, MORE of CLI, shows a description, syntax, parameter, and example for MORE commands. Chapter 17, NO Commands of CLI, shows a description, syntax, parameter, and example for NO commands.
For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller. Visit ATEN on the Web for a list of locations and telephone numbers: International...
Chapter 1 About This Guide Purpose This guide gives specific information on how to operate CLI to manage this switch. Audience The guide is intended for use by network administrators who are responsible for operating and maintaining network equipment; consequently, it requires a basic working knowledge of general switch functions, the RS-232 Console, Internet Protocol (IP), and Telnet Protocol.
Page 14
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
The following description briefly describes how to build up the network connection. Attach the RJ45 to DB9 Serial Console Cable to the console port on the ES0152 / ES0152P’s front panel for telnet configuration At “Com Port Properties” Menu, configure the parameters as below: (see the next section)
Example: Username: admin Password: F759a987 (example only*) ES0152# Note: For “<sys_name>#“, we will use ES0152 as an example for our ES0152 / ES0152P CLI User Manual. The password should be retrieved from the bottom sticker of the switch.
Chapter 2. CLI Management 2-2 Commands of CLI The CLI is divided into serveral modes. If a user has enouth privilege to run a particular command, the user has to run the command in the correct mode. To see the command modes, please input “?” after the system prompt, then all the commands will be listed in the screen.
Chapter 2. CLI Management 2-3 Global Commands of CLI Summary: ES0152# ? CableDiag Cable Diagnostic keyword clear Reset functions configure Enter configuration mode copy Copy from source to destination delete Delete one file in flash file system Directory of all files in flash file...
ES0152 / ES0152P CLI User Manual Exit Exit from EXEC mode. Syntax: Exit Parameters: None. Example: ES0152(config)# exit Help Description of the interactive help system. Syntax: Help Parameters: None. Example: ES0152# help Help may be requested at any point in a command by entering a question mark '?'.
Parameters: Parameter Description Interface Interface keyword GigabitEthernet 1 Gigabit Ethernet Port <port_type_id> Port ID in 1/1-48 Example: ES0152# CableDiag interface GigabitEthernet 1/1 Starting Cable Diagnostic - Please wait Interface Link Status Test Result Length ---------------------- ------------- ------------- GigabitEthernet 1/1 Link Down...
Page 24
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
Chapter 4 CLEAR of CLI Overview Table: CLEAR Commands Command Function access Access management access-list Access list dot1x IEEE Standard for port-based Network Access Control Clear DHCP Relay statistics ipv6 IPv6 configuration commands lacp Clear LACP statistics lldp Clear LLDP statistics for one or more given logging Syslog MAC Address Table...
ES0152 / ES0152P CLI User Manual ES0152# clear spanning-tree detected-protocols interface * 4-14 statistics Clear statistics for a given interface. Syntax: Clear statistics interface ( * | GigabitEthernet <port_list> ) Parameters: Parameter Description Interface Interface GigabitEthernet GigabitEthernet All switches or All ports <port__list>...
Page 33
Chapter 4. CLEAR of CLI Parameter Description Include Include lines that match <line> String to match output lines Example: ES0152# clear system led status software...
Page 34
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
Chapter 5 CONFIGURE Commands of CLI Overview Table: CONFIGURE Commands Command Function terminal Configure from the terminal Authentication, Authorization and Accounting access Access management access-list Access list aggregating Aggregation mode banner Define a banner clock Configure time-of-day clock default Set a command to its defaults DMS Mode To run exec commands in config mode dot1x...
Page 36
ES0152 / ES0152P CLI User Manual Command Function lldp LLDP configurations logging Syslog loop-protect Loop protection configuration MAC table entries/configuration monitor Monitoring different system events MVR multicast VLAN list mvrp Enable MVRP feature globally Negate a command or set its defaults...
ES0152 / ES0152P CLI User Manual Parameter Description Telnet Configure Telnet. HTTP Configure HTTP. Local Use local database for authentication. Radius Use RADIUS for authentication. TACACS Use TACACS+ for authentication. HTTPS Configure HTTPS. <0-65535> Service port (0..65535). Telnet Telnet. SSH.
Page 42
ES0152 / ES0152P CLI User Manual Parameter Description Don't-care the ingress interface. Interface Select an interface to configure. All switches or All ports. GigabitEthernet GigabitEthernet. <port_list> Port list in (1/1-52). Disable Disable metering. Disable Disable mirror. Disable Disable counter. <16-1000000000>...
Don't-care the value of source MAC address field. <mac_addr> The value of source MAC address field. Don't-care the value of etype field. <0x0000-0xFFFF> The value of etype field. Example: ES0152(config)# access-list ace 10 action deny 5-1.4 aggregation Aggregation mode. Syntax:...
Hour to start. (0..23). <1-12> Month to end. (1..12). <1-5> Week number to end. (1..5). <1-7> Weekday to end. (1..7). <0-23> Hour to end. (0..23). <1-1440> Offset to add in minutes. (1..1440). Example: ES0152(config)# clock set 2014/11/04 10:22:03 2014-11-04T10:22:03+00:00 ES0152(config)# do show clock...
ES0152 / ES0152P CLI User Manual System Time : 2014-11-04T10:22:48+00:00 5-1.7 default Set a command to its defaults. Syntax: Default access-list rate-limiter [ <rate_limiter_list> ] Parameters: Parameter Description Access-list Access list. Rate-limiter Rate limiter. <RateLimiterId : 1-16> Rate limiter ID.
Page 47
Chapter 5. CONFIGURE Commands of CLI Do < LINE >{[< LINE >]} Do clear access-list ace statistics Do clear ip dhcp relay statistics Do clear lldp statistics { global | [ interface ( GigabitEthernet <port_list> | * ) ] Do clear logging [ error | info | warning ] Do clear spanning-tree detected-protocols interface ( GigabitEthernet <port_list>...
ES0152 / ES0152P CLI User Manual Parameter Description Rmon Group ID RMON. Group ID SFP. Spanning-tree Group ID SPANNING-TREE. System Group ID SYSTEM. User Group ID USER. Warm-start Group ID WARM-START. Level Event group level. Syslog Syslog mode. Trap Trap mode.
Parameters: Parameter Description Time Config gvrp timer value in units of centi seconds [cs]. Example: ES0152(config)# gvrp max-vlans 333 ES0152(config)# gvrp time join-time 13 leave-all-time 3000 leave-time 200 5-1.16 help Description of the interactive help system. Syntax: Help Parameter: None.
ES0152 / ES0152P CLI User Manual argument. 2. Partial help is provided when an abbreviated argument is entered and you want to know what arguments match the input (e.g. 'show pr?'.) 5-1.17 hostname Set system’s network name. Syntax: Hostname <WORD>...
Fallback DHCP fallback settings. Timeout DHCP fallback timeout. <0-4294967295> DHCP fallback timeout in seconds (0..4294967295). Address Address configuraton. IPv6 mode. <port_list> Port List S/X-Y,Z (1/1-52). Example: ES0152(config)# interface GigabitEthernet 1/1-52 ES0152(config-if)# ES0152(config-if)# interface vlan 3 ES0152(config-if-vlan)# 5-1.19 ip Internet Protocol.
Page 56
ES0152 / ES0152P CLI User Manual Syntax: IP arp inspection IP arp inspection entry interface [ * | GigabitEthernet <port_id> ] <vlan_id> <mac_ucast> <ipv4_ucast> IP arp inspection vlan <vlan_list> IP arp inspection vlan <vlan_list> logging [ deny | permit | all ] IP dhcp pool <vlan_id>...
Page 57
Chapter 5. CONFIGURE Commands of CLI Parameter Description Entry Arp inspection entry. VLAN Arp inspection vlan setting. Interface Select an interface to configure. All switches or All ports. GigabitEthernet GigabitEthernet. <port_id> Port ID in (1/1-52). <vlan_id> Select a VLAN id to configure (1-4095). <mac_ucast>...
ES0152 / ES0152P CLI User Manual ES0152(config)# ipv6 mld snooping 5-1.22 lacp Lacp system configuration. Syntax: LACP system-priority <1-65535> Parameters: Parameter Description System-priority System priority. <1-65535> Aggregation group number (1..65535). Example: ES0152(config)# lacp system-priority 333 5-1.23 line Configure a terminal line.
Page 61
Chapter 5. CONFIGURE Commands of CLI LLDP holdtime <2-10> LLDP med datum [ wgs84 | nad83_navd88 | nad83_mllw ] LLDP med fast <1-10> LLDP med location-tlv altitude [ meters | floors ] <-32767-32767> LLDP med location-tlv civic-addr [ country | state | county | city | district | block | street | leading-street-direction | trailing-street-suffix | street-suffix | house-no | house-no-suffix | landmark | additional-info | name | zip-code | building | apartment | floor | room-number | place-type | postal-community-...
Page 62
ES0152 / ES0152P CLI User Manual Parameter Description Nad83_navd88 North American vertical datum 1983. Wgs84 World Geodetic System 1984. <1-10> Fast start repeat count (1..10). Altitude Altitude parameter. Civic-addr Civic address information and postal information. Elin-addr Emergency Location Identification Number.
Page 63
Chapter 5. CONFIGURE Commands of CLI Parameter Description Street-suffix Street suffix – Example. Word50 Example: Ave, Platz (word50) (for street-suffix). House-no House number. Word50 Example: 21 (word50) (for house-no). House-no-suffix House number suffix. Word50 Example: A, 1/2 (word50) (for house-no-suffix). Landmark Landmark or vanity address.
Page 64
ES0152 / ES0152P CLI User Manual Parameter Description South Setting latitude direction to south. <0-90> Setting latitude direction to south (0..90). East Setting longitude direction to east. West Setting longitude direction to west. <0-180> Setting longitude direction to east (0..180).
Enable syslog server. <1-6> Host number (1..6). <hostname> Donain name of the log server. <ipv4_ucast> IP address of the log server (X.X.X.X). Example: ES0152(config)# logging host 3 192.155.3.2 ES0152(config)# ES0152(config)# logging on 5-1.26 loop-protect Loop protection configuration. Syntax: Loop-protect Loop-protect shutdown-time <10-604800>...
ES0152 / ES0152P CLI User Manual Parameter Description <10-604800> Shutdown time in second (10..604800). <1-10> Transmit time in second (1..10). Example: ES0152(config)# loop-protect ES0152(config)# loop-protect shutdown-time 333 ES0152(config)# loop-protect transmit-time 3 5-1.27 mac MAC table entries/configuration. Syntax: MAC address-table aging-time <10-1000000>...
Page 70
ES0152 / ES0152P CLI User Manual Command Function Page aggregation Aggregation mode See p. 61 banner Define a login banner See p. 61 clock Configure time-of-day clock See p. 61 dot1x IEEE Standard for port-based Network See p. 62 Access Control...
Chapter 5. CONFIGURE Commands of CLI Command Function Page Unmap Shared VLAN Learning for a range See p. 82 or all FIDs switch2go-management SwitchAlert Management configuration See p. 83 system Set the SNMP server’s configurations See p. 83 tacacs-server Configure TACACS+ See p.
Guest VLAN even if an EAPOL frame has been received on the port for the life-time of the port. Tx-period The time between EAPOL retransmissions. Example: ES0152(config)# no dot1x authentication timer re- authenticate ES0152(config)# no dot1x guest-vlan supplicant ES0152(config)# no dot1x max-reauth-req ES0152(config)# no dot1x re-authentication...
ES0152 / ES0152P CLI User Manual Example: ES0152(config)# no enable secret level 15 ES0152(config)# no enable password level 15 5-1.31.9 green-ethernet Green ethernet (Power reduction). Syntax: No green-ethernet eee optimize-for-power Parameters: Parameter Description Powering down of PHYs when there is no traffic.
2004, clause 12.11. Leave-time Set GARP protocol parameter LeaveTime. See IEEE 802.1D-2004, clause 12.11. Example: ES0152(config)#no gvrp max-vlans 1 ES0152(config)#no gvrp time join-time 10 ES0152(config)#no gvrp time leave-all-time 2000 ES0152(config)#no gvrp time leave-time 70 5-1.31.11 hostname Set system’s network name. Syntax:...
Page 78
ES0152 / ES0152P CLI User Manual Syntax: No ip arp inspection No ip arp inspection entry interface { * | [ Gigabitethernet <port_id> ] } <vlan_id> <mac_ucast> <ipv4_ucast> No ip arp inspection vlan <vlan_list> logging No dhcp pool <vlan_id> No ip dhcp relay information [ option | policy ]...
Page 79
Select an unicast IP address to configure (X.X.X.X). <mac_ucast> Select an unicast MAC address to configure. Source Verify source. Example: ES0152(config)# no ip arp inspection vlan 3 logging ES0152(config)# no ip helper-address ES0152(config)# no ip igmp snooping ES0152(config)# no ip name-server...
ES0152 / ES0152P CLI User Manual ES0152(config)# no ip verify source 5-1.31.14 ipmc IPv4/IPv6 multicast configuration. Syntax: No mode No ipmc profile word16 No ipmc range word16 Parameters: Parameter Description Profile IPMC profile configuration. Range A range of IPv4/IPv6 multicast addresses for the profile.
Chapter 5. CONFIGURE Commands of CLI Example: ES0152(config)# no ipv6 mld snooping 5-1.31.16 lacp Lacp system configuration. Syntax: No lacp system-priority Parameters: Parameter Description System-priority System priority. Example: ES0152(config)# no lacp system-priority 5-1.31.17 lldp LLDP configurations. Syntax: No lldp holdtime...
Page 82
ES0152 / ES0152P CLI User Manual No lldp transmission-delay Parameters: Parameter Description Holdtime LLDP hold time. Media Endpoint Discovery. Reinit LLDP reinit time. Timer LLDP TX interval. Transmission-delay LLDP transmision-delay. Datum Datum type. Fast Number of times to repeat LLDP frame transmission at fast start.
Additional-code Additional code. <0~31> Policy id for the policy which is created (0..31). Example: ES0152(config)# no lldp holdtime ES0152(config)# no lldp med location-tlv civic-addr floor ES0152(config)# no lldp reinit ES0152(config)# no lldp timer ES0152(config)# no lldp transmission-delay 5-1.31.18 logging Syslog.
ES0152 / ES0152P CLI User Manual ES0152(config)# no logging host 3 ES0152(config)# no logging on 5-1.31.19 loop-protect Loop protection configuration. Syntax: No loop-protect No loop-protect shutdown-time No loop-protect transmit-time Parameters: Parameter Description Shutdown-time Loop protection shutdown time interval. Transmit-time Loop protection transmit time interval.
All switches or All ports. Gigabitethernet GigabitEthernet. <port_list> Port List S/X-Y,Z (1/1-52). Both Mirror both ingress and egress traffic. Mirror ingress traffic. Mirror egress traffic. Example: ES0152(config)# no monitor session 1 destination ES0152(config)# no monitor session 1 source interface GigabitEthernet 1/5 both...
ES0152 / ES0152P CLI User Manual 5-1.31.22 mvr Multicast VLAN Registration configuration. Syntax: No mvr Example: ES0152(config)# no mvr 5-1.31.23 mvrp None. Syntax: No mvrp Example: ES0152(config)# no mvrp 5-1.31.24 ntp Configure NTP. Syntax: No ntp No ntp server <1-6>...
The queue number for maaping to a specific DSCP value (0..7). <0-7> The queue number for mapping to a specific IP Precedence value (0..7). Example: ES0152(config)# no qos map cos-queue 3 5-1.31.30 radius-server Configure RADIUS. Syntax: No radius-server attribute [32 | 4 | 95]...
Page 90
UDP port number (0..65535). <AuthPort : 0-65535> UDP port number (0..65535). Example: ES0152(config)# no radius-server attribute 4 ES0152(config)# no radius-server deadtime ES0152(config)# no radius-server key ES0152(config)# no radius-server retransmit ES0152(config)# no radius-server timeout ES0152(config)# no radius-server host aa auth-port 3 acct-port 3...
Configure an RMON alarm. Event Configure an RMON event. <1-65535> Alarm entry ID (1..65535). <1-65535> Event entry ID (1..65535), Example: ES0152(config)# no rmon alarm 1000 5-1.31.32 sflow Statistics flow. Syntax: No sflow agent-ip No sflow collector-address No sflow collector-port No sflow max-datagram-size...
<Viewname : word32> MIB view name (word32). <Oidsubtree : word128> MIB view OID (word128). Example: ES0152(config)# no snmp-server access 333 model any level auth ES0152(config)# no snmp-server community v2c ES0152(config)# no snmp-server security-to-group model v2c name 132 ES0152(config)# no snmp-server View aa a 5-1.31.34 spanning-tree...
ES0152 / ES0152P CLI User Manual No spanning-tree mst max-hops No spanning-tree mst name Parameters: Parameter Description Mode STP protocol mode. STP bridge instance. <0-4094> MST instance ID , 0 is for CIST (0..4094). Forward-time Delay between port states. Max-age Max bridge age before timeout.
All switches or All ports. GigabitEthernet 1 Gigabit Ethernet Port. <port_type_list> Port list for all port types. <port_type_list> Port list in 1/1-26. Example: ES0152(config)# no switch2go-management port-name interface * 5-1.31.37 system Set the SNMP server’s configurations. Syntax: No system contact...
ES0152 / ES0152P CLI User Manual Parameter Description Description Clear the system description string. Reboot Erase all Switch Reboot scheduling. Example: ES0152(config)# no system name ES0152(config)# no system contact ES0152(config)# no system location 5-1.31.38 tacacs-server Configure TACACS+. Syntax: No tacacs-server deadtime No tacacs-server host word255 No tacacs-server host word255 port <AcctPort : 0-65535>...
Disable UDLD aggressive mode on all fiber-optic interfaces. Enable Disable UDLD on all fiber-optic interfaces. Example: ES0152(config)# no udld enable % Only fiber ports are allowed, port_no: 1 % Only fiber ports are allowed, port_no: 2 % Only fiber ports are allowed, port_no: 3...
ES0152 / ES0152P CLI User Manual Example: ES0152(config)# no upnp advertising-duration ES0152(config)# no upnp interface-vlan ES0152(config)# no upnp ttl 5-1.31.41 username Establish User Name Authentication. Syntax: No username word31 Parameters: Parameter Description Word31 User name allows letters, numbers and underscores (word31).
Dscp Prioritize packet based on the DSCP field in the IP header. IP-precedence Prioritize packet based on the IP precedence. Example: ES0152(config)# qos map cos-queue 3 to 5 5-1.38 radius-server Configure RADIUS. Syntax: Radius-server attribute 32 word255 Radius-server attribute 4 <ipv4_ucast>...
ES0152 / ES0152P CLI User Manual Parameter Description Set RADIUS encryption key. Retransmit Specify the number of retries to active server. Timeout Time to wait for a RADIUS server to reply. Word255 (word255). <ipv4_ucast> (X.X.X.X). <ipv6_addr> (X:X:X:X:X:X:X:X). <Minutes : 1-1440>...
Once the timeout reaches 0, the receiver and all its configuration is reset to defaults. <0-2147483647> Number in seconds . Example: ES0152(config)# sflow agent-ip ipv4 192.168.0.2 ES0152(config)# sflow collector-port 3 ES0152(config)# sflow max-datagram-size 333 ES0152(config)# sflow timeout 3333 5-1.41 smtp Set email information.
ES0152 / ES0152P CLI User Manual Parameter Description Exclude Excluded type from the view. Example: ES0152(config)# snmp-server view text .1 include 5-1.43 spanning-tree Spanning Tree protocol. Table: configure - spanning-tree Commands Command Function Page mode STP protocol mode See p. 102 STP bridge instance See p.
Page 119
The range is from 7 to 90 seconds(Currently default message time interval 7 sec is supported). Example: ES0152(config)# udld aggressive % Only fiber ports are allowed, port_no: 1 % Only fiber ports are allowed, port_no: 2 % Only fiber ports are allowed, port_no: 3...
ES0152 / ES0152P CLI User Manual % Only fiber ports are allowed, port_no: 21 % Only fiber ports are allowed, port_no: 22 % Only fiber ports are allowed, port_no: 23 % Only fiber ports are allowed, port_no: 24 % Only fiber ports are allowed, port_no: 25...
ES0152 / ES0152P CLI User Manual Parameter Description Encrypted Specifies an ENCRYPTED password will follow. None NULL password. Unencrypted Specifies an UNENCRYPTED password will follow. Word4-44 The ENCRYPTED (hidden) user password. Notice the ENCRYPTED password will be decoded by system internally.
VLAN ID required for the group to VLAN mapping (1-4095). <mac_ucast> 48 bit unicast MAC address: xx:xx:xx:xx:xx:xx. Example: ES0152(config)# vlan ethertype s-custom-port 0x1111 ES0152(config)# vlan protocol eth2 0x6000 group aa 5-1.52 voice Vlan for voice traffic. Syntax: Voice vlan oui <oui>...
ES0152 / ES0152P CLI User Manual Parameter Description VLAN voice_VLAN_mode help. Set a entry VLAN ID. OUI configuration. <vlan_id> VLAN IDs 1-4095 (1-4095). Aging-time Set a entry secure learning aging time. Class Set a entry traffic class. <AgingTime : Aging time, 10-10000000 seconds (10..10000000).
Chapter 10 DO Commands of CLI Overview To run exec commands in config mode. Syntax: Do <LINE>{[LINE]} Parameters: Parameter Description LINE Exec Command Example: ES0152# do show clock System Time : 2011-01-01T00:03:44+00:00...
Page 136
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
Dot1x initialize [ interface ( <port_type> [ <plist> ] ) ] Parameters: Parameter Description Initialize Force re-authentication immediately Interface Interface All switches or All ports Gigabitethernet 1 GigabitEthernet port <port_type_list> Port list for all port types <port_type_list> Port list in 1/1-52 Example: ES0152# dot1x initialize interface GigabitEthernet 1/1-...
Page 138
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
Firmware upgrade <tftp://server/path-and-filename> Parameters: Parameter Description Swap Swap between Active and Alternate firmware image Upgrade Upgrade <tftp://server/path-and- TFTP Server IP address, path and file name for the filename> server containing the new image Example: ES0152# firmware upgrade tftp://192.168.0.1/running- config Programming image...
Page 142
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
Chapter 17 NO Commands of CLI Overview Negate a command or set its defaults. Syntax: No debug prompt Parameters: Parameter Description Debug Debugging functions Terminal Set terminal line parameters Gdbserver Interrupt Application-handled interrupt source IPv6 IPv6 configuration commands Trace Output modifiers Begin Begin with the line that matches Exclude...
Page 150
ES0152 / ES0152P CLI User Manual Parameter Description Editing Enable command line editing Exec- Set the EXEC timeout timeout History Control the command history function Length Set number of lines on a screen Width Set width of the display terminal...
Virtual terminal <0~15> Send a message to multiple lines <LINE128> Message to be sent to lines, in 128 char's Example: ES0152# send * yes,i do Enter TEXT message. End with the character 'y'. ----------------------------------------- *** Message from line 0: yes,i do...
Page 158
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
Chapter 22 SHOW of CLI Overview Show running system information. Table: SHOW Commands Command Function Login methods. access Access management configuration. access-list Access list. aggregation Aggregation configuration and status. clock Configure time-of-day clock. dot1x IEEE Standard for port-based Network Access Control. event Show trap event configuration.
ES0152 / ES0152P CLI User Manual Command Function Power over ethernet. port-secuirty Show port security. privilege Display privilege level configuration. process Process. pvlan PVLAN status. Quality of Service. radius-server RADIUS configuration. rmon RMON statistics. running-config Current operating configuration. sflow Statistics flow.
Description LACP LACP local and neighbor info. Mode Traffic distribution mode. Status Aggregation port status. Example: ES0152# show aggregation mode Aggregation Hash Mode : src-dst-mac LACP System Priority : 32768 22-5 clock Configure time-of-day clock. Syntax: Show clock Example: ES0152# show clock...
ES0152 / ES0152P CLI User Manual Parameter Description All Ports. Gigbitethernet 1 Gigabit Ethernet Port. <port _list> Port ID (1/1-52). Show all dot1x statistics. Eapol Show EAPOL statistics. Radius Show Backend Server statistics. Example: ES0152# show dot1x statistics radius Rx Access Rx Other Rx Auth.
Chapter 22. SHOW of CLI GigabitEthernet 1/N 22-7 event Show trap even configuration. Syntax: Show event Example: ES0152# show event Group Name Severity Level -------------------------------- ---------------- ACCESS-MGMT Info Info ARP-INSPECTION Warning AUTH-FAILED Warning BSC-PROTECTION Info Cold-Start Warning DHCP Info DHCP-SNOOPING...
Page 166
ES0152 / ES0152P CLI User Manual PORT Info PORT-SECURITY Info RMON Info Info SPANNING-TREE Info SYSTEM Info USER Info Warm-Start Warning ES0152# show event Group Name Syslog Mode -------------------------------- ---------------- ACCESS-MGMT Enabled Enabled ARP-INSPECTION Enabled AUTH-FAILED Enabled BSC-PROTECTION Enabled Cold-Start...
Page 167
Chapter 22. SHOW of CLI Enabled SPANNING-TREE Enabled SYSTEM Enabled USER Enabled Warm-Start Enabled ES0152# show event Group Name Trap Mode -------------------------------- ---------------- ACCESS-MGMT Disabled Disabled ARP-INSPECTION Disabled AUTH-FAILED Disabled BSC-PROTECTION Disabled Cold-Start Disabled DHCP Disabled DHCP-SNOOPING Disabled IP-SOURCE-GUARD Disabled...
ES0152 / ES0152P CLI User Manual Example: ES0152# show history show evc statistics show green-ethernet EEE show green-ethernet EEE interface GigabitEthernet show history 22-10 interface Interface status and configuration. Syntax: Show interface vlan <vlan_list> Show interface vlan Show interface { * | [ GigabitEthernet <port _list>] } green-ethernet Show interface { * | [ GigabitEthernet <port _list>] } capabilities...
Page 171
Show error statistics. Packets Show packet statistics. Show ports which are up. Down Show ports which are down. Example: ES0152# show interface GigabitEthernet 1/1-3 capabilities GigabitEthernet 1/1 Capabilities: SFP Type: None SFP Vendor name: SFP Vendor PN: SFP Vendor revision:...
Page 172
ES0152 / ES0152P CLI User Manual Show ip arp inspection entry { [ dhcp-snooping interface ] | [ interface ] | [ static interface ] } { * | [ GigabitEthernet <port _list> ] } Show ip arp inspection interface { * | [ GigabitEthernet <port _list> ] } Show ip arp inspection vlan <vlan_list>...
Page 173
Chapter 22. SHOW of CLI Show ip verify source interface { * | [ GigabitEthernet <port _list>] } Parameters: Parameter Description Address Resolution Protocol. DHCP Dynamic Host Configuration Protocol. IGMP Internet Protocol. Interface IP interface status and configuration. Name-server Domain Name System. Route Display the current ip routing table.
ES0152 / ES0152P CLI User Manual Parameter Description Mrouter Multicast router port status in IGMP. VLAN Search by VLAN. Brief Brief IP interface status. Binding IP source binding. Interface IP verify source interface config. Source Verify source. Example: ES0152# show ip interface brief...
Multicast router port status in MLD. VLAN Search by VLAN. VLAN VLAN of IPv6 interface. <vlan_list> IPv6 interface VLAN list (1-4095). Brief Brief summary of IPv6 status and configuration. Interface Select an interface to configure. Example: ES0152# show ipv6 mld snooping detail...
Include Include lines that match. <LINE> String to match output lines. Example: ES0152# show line alive Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled.
ES0152 / ES0152P CLI User Manual Show lldp Show lldp interface { * | [ GigabitEthernet <port _list> ] } Show lldp med media-vlan-policy Show lldp med media-vlan-policy <policy_list> Show lldp med remote-device Show lldp med remote-device interface { * | [ GigabitEthernet <port _list> ] } Show lldp neighbors Show lldp neighbors interface { * | [ GigabitEthernet <port _list>...
ES0152 / ES0152P CLI User Manual Show mac address-table learning interface { * | [ GigabitEthernet <port _list> Show mac address-table vlan <vlan_id> Parameters: Parameter Description Address-table MAC Address Table. Address MAC address lookup. Aging-time Aging time. Conf User added static mac addresses.
Page 183
Parameters: Parameter Description Session MIRROR session. <1-5> MIRROR session number. Show all MIRROR sessions. Remote Show only Remote MIRROR sessions. Example: ES0152# show monitor Session 1 --------- Mode : Disabled Type : Mirror Source VLAN(s) CPU Port Session 2 ---------...
Page 184
ES0152 / ES0152P CLI User Manual Session 4 --------- Mode : Disabled Type : Mirror Source VLAN(s) CPU Port Session 5 --------- Mode : Disabled Type : Mirror Source VLAN(s) CPU Port 22-21 mrp MRP status. Syntax: Show mrp status [ all | mvrp ] interface [ ( * | GigabitEthernet ) <port_type_list>...
Configure NTP. Syntax: Show ntp status Parameters: Parameter Description Status Status. Example: ES0152# show ntp status NTP Mode : Disable Interval : 1440 min Server IP host address (a.b.c.d) or a host name string ------------------------------------------------- 22-24 platform Platform configuration. Syntax: Show platform phy [ interface ( <port_type>...
ES0152 / ES0152P CLI User Manual Show platform phy status [ interface ( <port_type> [ <v_port_type_list> ] ) ] [ | {begin | exclude | include } <LINE>] Parameters: Parameter Description PHYs’ information. Output modifiers. Begin Begin with the line that matches.
Page 189
All Switches or All ports. Gigabitethernet GigabitEthernet <port_list> Port List S/X-Y,Z (1/1-52). Show poe profile. <1-16> Profile id (1..16). Example: ES0152# show poe status interface GigabitEthernet 1/1-2 Interface PD Class Port Status ---------------------- -------- ------------------- GigabitEthernet 1/1 No PD detected...
ES0152 / ES0152P CLI User Manual 22-29 pvlan PVLAN status. Syntax: Show pvlan Show pvlan <pvlan_list> Show pvlan isolation Show pvlan isolation interface { * | [ GigabitEthernet <port _list> ] } Parameters: Parameter Description <pvlan_list> PVLAN ID to show configuration for (1-10).
Map for IP Precedence to queue. Queue-cos Map for queue to CoS. Queue-dscp Map for queue to DSCP. Queue-precedence Map for queue to IP Precedence. Example: ES0152# show qos map queue-precedence Queue to IP Precedence mappings Queue ---------------+------------------------ IP Precedence 22-31 radius-server RADIUS configuration.
ES0152 / ES0152P CLI User Manual Syntax: Show radius-server Show radius-server statistics Parameters: Parameter Description Statistics RADIUS statistics. Example: ES0152# show radius-server statistics Global RADIUS Server Timeout : 5 seconds Global RADIUS Server Retransmit : 3 times Global RADIUS Server Deadtime...
<1-65535> History entry list (1..65535). <1-65535> Statistics entry list (1..65535). <1-65535> Alarm entry list (1..65535). <1-65535> Event entry list (1..65535). Example: ES0152# show rmon statistics 5 22-33 running-config Current operating configuration. Syntax: Show running-config Parameters: Parameter Description CWORD Valid words are GVRP’...
Page 197
Begin Begin with the line that matches. Exclude Exclude lines that match. Include Include lines that match. <LINE> String to match output lines. Example: ES0152# show sflow Agent Configuration: ==================== Agent Address: 127.0.0.1 Receiver Configuration: ======================= Owner : <none> Receiver : 0.0.0.0...
ES0152 / ES0152P CLI User Manual Time left : 0 seconds No enabled collectors (receivers). Skipping displaying per-port info. 22-35 smtp Show email information. Syntax: Show smtp Example: ES0152# show smtp Mail Server User Name Password Sender Return Path Email Adress 1...
<SecurityName : word32> Security group name (word32). <UserName : word32> Security user name (word32). <ViewName : word32> MIB view name (word32). <OidSubtree : word128> MIB view OID (word128). Example: ES0152# show snmp SNMP Configuration Read Community : public Write Community : private...
Exclude lines that match. Include Include lines that match. <line> String to match output lines. <1~4095> List of FIDs to show. Example: ES0152# show svl fid 1 VLANs ---- ------------------------------ 1 (default) 22-39 switch2go-management Show Switch2go Management information. Syntax: Show switch2go-management> [ mobile-link | options | setting ]...
ES0152 / ES0152P CLI User Manual Parameter Description Mobile-link Show Registered Mobile Device List. Options Show Port Name Service configurations. Setting Show Switch2go Management configuration. Example: ES0152# show switch2go-management setting Switch2go Mode : Disabled Server Address : ipush.cloudapp.net Server State 22-40 switchport Display switching mode characteristics.
Chapter 22. SHOW of CLI 22-41 system Show system information. Syntax: Show system Parameters: None. Example: ES0152# show system Model Name System Description : Hardware Version : v1.01 Mechanical Version : v1.01 Firmware Version : v1.00.844 MAC Address : 00-40-C7-1F-00-7D...
ES0152 / ES0152P CLI User Manual Syntax: Show terminal [ | {begin | exclude | include } <LINE> Parameters: Parameter Description Output modifiers. Begin Begin with the line that matches. Exclude Exclude lines that match. Include Include lines that match.
String to match output lines. All switches or All ports. GigabitEthernet 1 Gigabit Ethernet Port. <port_type_list> Port list for all port types. <port_type_list> Port list in 1/1-52. Example: ES0152# show udld interface GigabitEthernet 1/1 GigabitEthernet 1/1 ------------------------------------------------------- --------------- UDLD Mode : Disable Admin State...
Elapsed time is 0 day 1 hour 33 min 27 sec. Idle time is 0 day 0 hour 0 min 0 sec. 22-48 version System software status. Syntax: Show version Example: ES0152# show version Active Image ------------ Partition : secondary Version : v1.00.844...
ES0152 / ES0152P CLI User Manual Show vlan ip-subnet address Show vlan ip-subnet address< ipv4_addr> Show vlan mac config Show vlan mac config address <mac_ucast> Show vlan mac status Show vlan mac status address <mac_ucast> Show vlan mapping Show vlan protocol Show vlan protocol { [ eth2 <ethernet value>...
Page 209
Show the VLANs configured by Voice VLAN. All Switches or All ports. Gigabitethernet GigabitEthernet. <port_list> Port List S/X-Y,Z (1/1-52). Example: ES0152# show vlan status all interface GigabitEthernet GigabitEthernet 1/4 : --------------------- VLAN User PortType PVID Frame Type Ing Filter ---------...
Page 210
ES0152 / ES0152P CLI User Manual GVRP Voice VLAN MSTP Combined C-Port Enabled ES0152# show vlan status all interface GigabitEthernet GigabitEthernet 1/4 : --------------------- VLAN User Tx Tag --------- ------------- --- Admin None GVRP Voice VLAN MSTP Combined None 22-50 voice Show voice.
Web privilege group level. Output modifiers. Begin Begin with the line that matches. Exclude Exclude lines that match. Include Include lines that match. <LINE> String to match output lines. Example: ES0152# show web privilege group level Group Name Privilege Level...
Chapter 25 CLI COMMAND REFERENCES Overview This chapter introduces the CLI privilege level and command modes. The privilege level determines whether or not the user could run the particular commands. If the user could run the particular command, then the user has to run the command in the correct mode.
Page 222
ES0152 / ES0152P CLI User Manual Command Table COMMAND DESCRIPTION Use the show access management user EXEC command with- out keywords to dis- play the access management configu- show access management ration, or use the sta- EXEC tistics keyword to display statistics, or use the <AccessId>...
Page 223
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the no access management <Acces- sIdList> global configu- GLOBAL no access management <1~16> ration command to _CONFIG delete the specific access management entry. Use the access-list action interface config- uration command to INTER- configure access-list FACE_P...
Page 224
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the no access-list redirect interface con- figuration command to disable the access-list INTER- redirect. The access- FACE_P no access-list { redirect | port-copy } list interface configura- ORT_LIS tion will affect the...
Page 225
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the access-list evc-policer interface configuration com- mand to configure the INTER- access-list evc-policer FACE_P access-list evc-policer <1-256> ID. The access-list ORT_LIS interface configuration will affect the received frames if it doesn't match any ACE. Use the no access-list evc-policer interface configuration com-...
Page 226
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the access-list port-state interface configuration com- INTER- mand to enable FACE_P access-list port-state access-list port state. ORT_LIS Use the no form of this command to disable access-list port state. access-list rate-limiter [ <1~16> ] { pps...
Page 228
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the no access-list ace global configura- GLOBAL no access-list ace <1~256> tion command to _CONFIG delete the access-list ace. Use the show access- list privilege EXEC command without key- words to display the...
Page 229
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the show access- list ace-status privi- lege EXEC command without keywords to display the access-list ace status for all access-list users, or show access-list ace-status [ static ] [ link- particularly the access- oam ] [ loop-protect ] [ dhcp ] [ ptp ] [ upnp ] list user for the access- [ arp-inspection ] [ mep ] [ ipmc ] [ ip-...
Page 230
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the ip arp inspec- tion global configura- tion command to globally enable ARP GLOBAL ip arp inspection vlan <vlan_list> inspection. Use the no _CONFIG form of this command to globally disable ARP inspection.
Page 231
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the ip arp inspec- tion logging interface configuration com- mand to configure a INTER- ip arp inspection logging { deny | permit | all port as some logging FACE_P mode for ARP inspec- ORT_LIS tion purposes.
Page 232
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the no radius- server retransmit com- mand to reset the GLOBAL no radius-server retransmit global RADIUS _CONFIG retransmit value to default. Use the radius-server deadtime command to GLOBAL radius-server deadtime <1-1440>...
Page 233
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the no radius- no radius-server host <word1-255> [ auth- server host command GLOBAL port <0-65535> ] [ acct-port <0-65535> ] to delete an existing _CONFIG RADIUS host. Use the tacacs-server timeout command to GLOBAL tacacs-server timeout <1-1000>...
Page 234
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the show aaa command to view the GLOBAL show aaa currently active _CONFIG authentication login methods. Use the show radius- server command to show radius-server [ statistics ] view the current...
Page 235
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION GLOBAL no clock timezone _CONFIG show clock detail EXEC Use the show ip dhcp detailed statistics user EXEC command to display statistics. Notice that the normal forward per-port TX statistics isn't show ip dhcp detailed statistics { server | increased if the incom- client | snooping | relay | normal-forward | ing DHCP packet is...
Page 236
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the show ip dhcp relay user EXEC com- mand without key- words to display the show ip dhcp relay [ statistics ] EXEC DHCP relay configura- tion, or use the statis- tics keyword to display statistics.
Page 237
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the ip dhcp relay information option global configuration command to enable the DHCP relay infor- mation option. Use the no form of this com- mand to disable the DHCP relay informa- tion option. The option 82 circuit ID format as "[vlan_id][mod- ule_id][port_no]".
Page 238
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the ip dhcp relay information policy global configuration command to configure the DHCP relay infor- mation policy. When DHCP relay informa- tion mode operation is ip dhcp relay information policy { drop |...
Page 239
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION GLOBAL ip dhcp server _CONFIG ip dhcp excluded-address <ipv4_addr> GLOBAL [<ipv4_addr>] _CONFIG GLOBAL no ip dhcp pool <word32> _CONFIG INTER- ip dhcp server FACE_VL DHCP_P network <ipv4_addr> <ipv4_netmask> DHCP_P no network DHCP_P broadcast <ipv4_addr> DHCP_P no broadcast default-router <ipv4_ucast>...
Page 241
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION vendor class-identifier <string64> specific- DHCP_P info <hexval32> DHCP_P no vendor class-identifier <string64> debug dhcp server memsize EXEC debug dhcp server declined add EXEC <ipv4_addr> debug dhcp server declined delete EXEC <ipv4_addr> Use the show ip dhcp snooping user EXEC show ip dhcp snooping [ interface <port_- command to display...
Page 242
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the ip dhcp snoop- ing trust interface con- figuration command to INTER- configure a port as FACE_P dhcp_snooping_port_mode trusted for DHCP ORT_LIS snooping purposes. Use the no form of this command to configure a port as untrusted.
Page 243
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Sets temperature at GLOBAL green-ethernet fan temp-on <-127-127> which to turn fan on to _CONFIG the lowest speed. Sets temperature at which to turn fan on to GLOBAL no green-ethernet fan temp-on the lowest speed to _CONFIG default.
Page 244
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION INTER- green-ethernet eee urgent-queues Sets EEE urgeent FACE_P [<range_list>] queues. ORT_LIS Sets if EEE should be optimized for least traf- GLOBAL green-ethernet eee optimize-for-power fic latency or least _CONFIG power comsumption INTER-...
Page 245
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the http secure- redirect global configu- ration command to enable the secure HTTP web redirection. When the secure HTTP web server is enabled, the feature GLOBAL ip http secure-redirect automatic redirect the _CONFIG none secure HTTP web connection to the...
Page 246
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION debug icfg silent-upgrade status EXEC debug icfg dir EXEC debug icfg error-trace <line> EXEC Enable routing for IPv4 GLOBAL ip routing and IPv6 _CONFIG Disable routing for GLOBAL no ip routing IPv4 and IPv6 _CONFIG ip address {{<ipv4_addr>...
Page 247
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION debug ipstack log [ERR|NOERR] [WARN- ING|NOWARNING] [NOTICE|NONOTICE] [INFO|NOINFO] [DEBUG|NODEBUG] [MDEBUG|NOMDEBUG] EXEC [IOCTL|NOIOCTL] [INIT|NOINIT] [ADDR|NOADDR] [FAIL|NOFAIL] [EMERG|NOEMERG] [CRIT|NOCRIT] debug ip kmem EXEC debug ip route EXEC debug ip sockets EXEC debug ip lpm stat ip <vlan_list> EXEC debug ip lpm stat ipv6 <vlan_list>...
Page 248
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION GLOBAL ip igmp snooping _CONFIG GLOBAL ip igmp unknown-flooding _CONFIG GLOBAL ip igmp host-proxy [ leave-proxy ] _CONFIG GLOBAL ip igmp ssm-range <ipv4_mcast> <4-32> _CONFIG GLOBAL no ip igmp ssm-range _CONFIG GLOBAL ip igmp snooping vlan <vlan_list>...
Page 249
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION INTER- no ip igmp snooping robustness-variable FACE_VL INTER- ip igmp snooping query-interval <1-31744> FACE_VL INTER- no ip igmp snooping query-interval FACE_VL INTER- ip igmp snooping query-max-response-time FACE_VL <0-31744> INTER- no ip igmp snooping query-max-response- FACE_VL time INTER-...
Page 250
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION INTER- FACE_P no ip igmp snooping max-groups ORT_LIS INTER- FACE_P ip igmp snooping filter <word16> ORT_LIS INTER- FACE_P no ip igmp snooping filter ORT_LIS GLOBAL ipv6 mld snooping _CONFIG GLOBAL ipv6 mld unknown-flooding...
Page 252
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION INTER- no ipv6 mld snooping robustness-variable FACE_VL INTER- ipv6 mld snooping query-interval <1- FACE_VL 31744> INTER- no ipv6 mld snooping query-interval FACE_VL INTER- ipv6 mld snooping query-max-response- FACE_VL time <0-31744> INTER- no ipv6 mld snooping query-max-response-...
Page 253
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION GLOBAL ip verify source translate _CONFIG show ip verify source [interface <port_- EXEC type_list>] show ip source binding [ dhcp-snooping | EXEC static ] [interface <port_type_list>] ip source binding interface <port_type_id> GLOBAL <vlan_id> <ipv4_ucast> <mac_ucast> _CONFIG ip source binding interface <port_type_id>...
Page 254
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Sets LLDP hold time (The neighbor switch will discarded the GLOBAL lldp holdtime <2-10> LLDP information after _CONFIG \"hold time\" multiplied with \"timer\" seconds ) GLOBAL no lldp holdtime _CONFIG Sets LLDP TX interval...
Page 255
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Sets LLDP transmis- ion-delay. LLDP trans- mission delay (the amount of time that the GLOBAL lldp transmission-delay <1-8192> transmission of LLDP _CONFIG frames will delayed after LLDP configura- tion has changed) in seconds.) GLOBAL no lldp transmission-delay _CONFIG...
Page 256
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the lldp med loca- lldp med location-tlv altitude { meters | tion-tlv altitude to con- GLOBAL floors } <word11> figure the location _CONFIG altitude. Use the lldp med loca- tion-tlv altitude to con-...
Page 257
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the lldp med lldp med datum { wgs84 | nad83-navd88 | datum to configure the GLOBAL nad83-mllw } datum (geodetic sys- _CONFIG tem) to use. GLOBAL no lldp med datum _CONFIG Use the lldp med fast to configure the num- ber of times the fast start LLDPDU are...
Page 264
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION GLOBAL mvr name <word16> frame tagged _CONFIG GLOBAL no mvr vlan <vlan_list> frame priority _CONFIG GLOBAL no mvr name <word16> frame priority _CONFIG mvr vlan <vlan_list> last-member-query- GLOBAL interval <0-31744> _CONFIG mvr name <word16> last-member-query- GLOBAL interval <0-31744>...
Page 265
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION GLOBAL no dot1x timeout tx-period _CONFIG Time in seconds between check for dot1x authentication timer inactivity <10- GLOBAL activity on success- 1000000> _CONFIG fully authenticated MAC addresses. GLOBAL no dot1x authentication timer inactivity _CONFIG Time in seconds before a MAC-address...
Page 266
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION The number of times a Request Identity EAPOL frame is sent GLOBAL dot1x max-reauth-req <1-255> without response _CONFIG before considering entering the Guest VLAN The number of times a Request Identity EAPOL frame is sent...
Page 267
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION INTER- Enables/disables per- FACE_P dot1x radius-qos port state of RADIUS- ORT_LIS assigned QoS. INTER- Enables/disables per- FACE_P dot1x radius-vlan port state of RADIUS- ORT_LIS assigned VLAN. Globally enables/dis- dot1x feature { [ guest-vlan ] [ radius-qos ] [ GLOBAL ables a dot1x feature radius-vlan ] }*1...
Page 269
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION INTER- Use poe priority to con- FACE_P poe priority { low | high | critical } figure PoE priority. ORT_LIS INTER- Use poe priority to con- FACE_P no poe priority figure PoE priority. ORT_LIS poe management mode { class-consump- Use management...
Page 270
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION disable PoE power GLOBAL no poe schedule-all <range_list> management method. _CONFIG Configure PoE Power GLOBAL poe delay-mode <range_list> Delay mode. _CONFIG GLOBAL no poe delay-mode <range_list> _CONFIG Configure PoE Power GLOBAL poe delay-time <range_list> <0-300>...
Page 271
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION This command is used INTER- to set hour time on FACE_P poe Wed Wednesday to enable ORT_LIS PoE. This command is used INTER- to set hour time on FACE_P no poe Wed Wednesday to disable ORT_LIS PoE.
Page 272
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Display status for the show interface <port_type_list> status EXEC interface. INTER- mtu <'VTSS_MAX_FRAME_LENGTH_- Use mtu to specify FACE_P STANDARD'-'VTSS_MAX_- maximum frame size ORT_LIS FRAME_LENGTH_MAX'> (1518-9600 bytes). INTER- Use no mtu to set max-...
Page 273
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION INTER- Use flowcontrol to con- FACE_P flowcontrol { on | off } figure flow control for ORT_LIS the interface. INTER- Use no flowcontrol to FACE_P no flowcontrol set flow control to ORT_LIS default. Use excessive-restart INTER- to configure backoff...
Page 274
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Maximum number of INTER- MAC addresses that FACE_P port-security maximum [<1-1024>] can be learned on this ORT_LIS set of interfaces. INTER- FACE_P no port-security maximum ORT_LIS INTER- The action involved port-security violation { protect | trap | trap-...
Page 275
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION no qos map dscp-ingress-translation { GLOBAL <0~63> | <dscp> } _CONFIG GLOBAL qos map dscp-classify { <0~63> | <dscp> } _CONFIG qos map cos-dscp <0~7> dpl <0~1> dscp { GLOBAL <0-63> | <dscp> } _CONFIG GLOBAL no qos map cos-dscp <0~7>...
Page 282
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION The agent IP address used as agent-address sflow agent-ip {ipv4 <ipv4_addr> | ipv6 GLOBAL in UDP datagrams. <ipv6_addr>} _CONFIG Defaults to IPv4 loop- back address. Sets the agent IP address used as...
Page 283
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION no sflow max-datagram-size [receiver Maximum datagram GLOBAL <range_list>] size. _CONFIG Specifies the statisti- cal sampling rate. The sample rate is speci- fied as N to sample 1/ INTER- Nth of the packets n sflow sampling-rate [sampler <range_list>] FACE_P the monitored flows.
Page 284
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION GLOBAL smtp sender <word47> _CONFIG GLOBAL smtp username <word31> <word31> _CONFIG GLOBAL smtp server <word47> _CONFIG GLOBAL smtp level <0-7> _CONFIG show snmp EXEC show snmp community v3 [ <word127> ] EXEC show snmp user [ <word32>...
Page 285
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION snmp-server user <word32> engine-id <word10-32> [ {md5 <word8-32> | sha GLOBAL <word8-40> } [ priv { des | aes } <word8- _CONFIG 32> ] ] no snmp-server user <word32> engine-id GLOBAL <word10-32> _CONFIG snmp-server security-to-group model { v1 | GLOBAL v2c | v3 } name <word32>...
Page 286
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the show snmp mib ifmib ifIndex user EXEC command to \ display the show snmp mib ifmib ifIndex EXEC SNMP ifIndex(defined in IF-MIB) mapping \ information in the switch. Use the show snmp...
Page 288
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the ip ssh global configuration com- mand to \ enable the GLOBAL ip ssh SSH. Use the no form _CONFIG of this \ command to disable the SSH. show network-clock Show selector state.
Page 289
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION no network-clock clk-source <range_list> GLOBAL priority _CONFIG WTR time (0-12 min) GLOBAL network-clock wait-to-restore <0-12> '0' is disable _CONFIG GLOBAL no network-clock wait-to-restore _CONFIG network-clock ssm-holdover { prc | ssua | Hold Over SSM over- GLOBAL ssub | eec2 | eec1 | dnu | inv } write...
Page 290
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the show logging privileged EXEC com- show logging <1-4294967295> [ switch mand with logging ID EXEC <switch_list> ] to display the detail logging message. OC_CMD_DEFAULT = Use the clear logging clear logging [ info ] [ warning ] [ error ] [...
Page 291
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the password encrypted <pass- word> global configu- ration command to GLOBAL password unencrypted <line31> configure administra- _CONFIG tor password with unencrypted password for the local switch access. Use the password encrypted <pass- word>...
Page 292
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION thermal-protect prio <0~3> temperature <0- Thermal protection GLOBAL 255> configuirations. _CONFIG Sets temperature at which to turn ports with GLOBAL no thermal-protect prio <0~3> the corresponding pri- _CONFIG ority off. Sets temperature at...
Page 293
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the username <username> privilege <level> password encrypted <pass- username <word31> privilege <0-15> GLOBAL word> global configu- password encrypted <word4-44> _CONFIG ration command to add a user with encrypted password for the local switch access.
Page 294
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION INTER- switchport vlan ip-subnet id <1-128> FACE_P <ipv4_subnet> vlan <vlan_id> ORT_LIS INTER- FACE_P no switchport vlan ip-subnet id <1~128> ORT_LIS INTER- FACE_P debug vcl policy <uint> ORT_LIS GLOBAL no debug vcl policy...
Page 295
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the switchport INTER- native vlan command FACE_P switchport hybrid native vlan <vlan_id> to configure a port ORT_LIS VLAN ID for a hybrid port. INTER- Set hybrid mode char- FACE_P no switchport hybrid native vlan acteristics of the inter- ORT_LIS face...
Page 296
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION INTER- Set trunk mode char- switchport trunk allowed vlan {all | none | FACE_P acteristics of the inter- [add | remove | except] <vlan_list>} ORT_LIS face INTER- Set trunk characteris- FACE_P no switchport trunk allowed vlan...
Page 297
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Adds or removes for- INTER- switchport forbidden vlan {add|remove} bidden VLANs from the FACE_P <vlan_list> current list of forbid- ORT_LIS den VLANs INTER- Allows for adding FACE_P no switchport forbidden vlan VLANs to an interface ORT_LIS show switchport forbidden [{vlan <vlan_id>} Lookup VLAN Forbid-...
Page 298
ES0152 / ES0152P CLI User Manual COMMAND DESCRIPTION Use the no voice vlan class global configura- GLOBAL no voice vlan class tion command to _CONFIG restore the default voice vlan class. Use the voice vlan oui global configuration GLOBAL voice vlan oui <oui> [description <line32>]...
Page 299
Chapter 25. CLI COMMAND REFERENC- COMMAND DESCRIPTION Use the no switchport voice vlan discovery- INTER- protocol interface con- FACE_P no switchport voice vlan discovery-protocol figuration command to ORT_LIS restore the default switchport voice vlan discovery-protocol. Use the show voice vlan privilege EXEC command without key- words to display the show voice vlan [ oui <oui>...
Page 300
ES0152 / ES0152P CLI User Manual This Page Intentionally Left Blank...
Need help?
Do you have a question about the ES0152 and is the answer not in the manual?
Questions and answers