Raven SmarTrax Installation Manual

Case ih patriot 4420 (2009 & newer), spx 4410/4420 (2008 & older), spx 4260 (s/n jfg003537 & newer)
Hide thumbs Also See for SmarTrax:

Advertisement

Quick Links

Case IH Patriot 4420 (2009 & Newer),
SPX 4410/4420 (2008 & Older), SPX
4260 (S/N JFG003537 & Newer)
SmarTrax™ Installation Manual
P/N 016-5032-017 Rev A
09/15
E19402
Copyright 2012, 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SmarTrax and is the answer not in the manual?

Questions and answers

Summary of Contents for Raven SmarTrax

  • Page 1 Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual P/N 016-5032-017 Rev A 09/15 E19402 Copyright 2012, 2015...
  • Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
  • Page 3: Table Of Contents

    Hydraulic System Installation..........9 Install Fittings in the SmarTrax Valve ..................10 Install Fittings in the Flow Switch .................... 11 Install the SmarTrax Valve and Flow Switch ................11 Install the Left and Right Steering Hoses ................13 Install the Pressure Hose ......................
  • Page 4 Table of Contents Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 5: Important Safety Information

    Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine. WARNING • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. •...
  • Page 6: Hydraulic Safety

    • Ensure that the power cable is the last cable to be connected. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 7: Introduction

    Preparing for Installation Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic system by loosening the hydraulic fittings slowly, where applicable.
  • Page 8: Recommendations

    We will not share your email or any information you provide with anyone else. Your feedback is valued and extremely important to us. Thank you for your time. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 9: Kit Contents

    This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 10 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 Nut - 5/16”-18 Flanged Lock 312-1001-169 Nut - M6 Lock 312-4000-207 Washer - 1/4” Split Lock 313-1000-016 Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 11 Introduction SmarTrax Installation Kit (P/N 117-5032-017 or 117-5032-018) TABLE 1. Picture Item Description Part Number Qty. Washer - 5/16” Split Lock 313-1000-019 Washer - 0.25” ID x 0.562” OD 313-2300-009 Hydraulic Kit (P/N 117-0199-017) TABLE 2. Picture Item Description Part Number Qty.
  • Page 12 Hydraulic Hose - -8 ORFS (F) to -6 ORFS (F) 214-1000-658 - 60” Hydraulic Hose - -6 ORFS (F) 90° to -6 214-1000-659 ORFS (F) - 108” Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 13: Hydraulic System Installation

    WARNING Hydraulics are under pressure. Care should always be taken with a system that has been pressurized. Before beginning the SmarTrax hydraulic installation, turn off the machine and relieve pressure by turning the steering wheel left and right. Never work on a hot machine. Always allow it to cool before performing diagnostics, maintenance, or routine service.
  • Page 14: Install Fittings In The Smartrax Valve

    Fitting - -6 ORFS (M) to -8 SAE O-Ring (M) Straight Adapter 333-0012-199 P, T Fitting - -6 ORFS (M) to -10 SAE O-Ring (M) Straight Adapter 333-0012-233 A, B Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 15: Install Fittings In The Flow Switch

    SmarTrax Valve and Flow Switch Installed on Mounting Bracket FIGURE 3. Install the SmarTrax valve (P/N 334-0003-088) on the valve mounting bracket (P/N 107-0171-705) using four 5/16”-18 x 7/8” hex bolts (P/N 311-0052-104) and four 5/16” split lock washers (P/N 313-1000-019).
  • Page 16 Align the holes in the valve mounting bracket with the holes in the machine’s radar bracket. Using the machine’s bolts, secure the valve mounting bracket to the radar bracket. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 17: Install The Left And Right Steering Hoses

    Hydraulic System Installation Install the Left and Right Steering Hoses Machine’s Left Steering Hose FIGURE 6. Locate and disconnect the machine’s left steering hose form the left steering cylinder. Note: The left steering hose is connected to the fitting located closest to the center of the machine. Machine’s Left Steering Hose Installed on Flow Switch FIGURE 7.
  • Page 18 Connect the straight end of the installed hydraulic hose the fitting installed in Port B of the SmarTrax valve. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 19: Install The Pressure Hose

    Connect the 90° end of the supplied hydraulic hose (P/N 214-1000-657) on the 90° end of the installed tee fitting. Connect the straight end of the installed hydraulic hose to the fitting installed in Port P of the SmarTrax valve (P/N 334-0003-088).
  • Page 20 Connect the -6 end of the installed hydraulic hose to the fitting installed in Port T of the SmarTrax valve (P/N 334-0003-088). Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 21: Hydraulic Diagram

    Hydraulic System Installation Hydraulic Diagram Manual No. 016-5032-017 Rev. A...
  • Page 22 Chapter 3 Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 23: Cab Component Installation

    C h a p t e r 4 Installation Install the SmarTrax Node Note: The SmarTrax node (P/N 063-0173-228) is sold separately. Contact your local Raven dealer for ordering information. Mount the SmarTrax Node SmarTrax Node Mounting Location FIGURE 1.
  • Page 24 Back Panel Removed FIGURE 3. Back Wall of the Cab Bottom of Instructional Seat Compartment Remove the back panel. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 25: Node Mounting Locations

    Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. Manual No. 016-5032-017 Rev. A...
  • Page 26: Install The Foot Switch

    Route the remainder of the node harness (P/N 115-4001-110) through the opening in the side of the instructional seat and behind the operator’s seat. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 27 Cab Component Installation Locate the opening in the plastic shroud behind the operator’s seat. Locate the ENABLE connector on the node harness (P/N 115-4001-110) and connect it to the foot switch cable connector. DGPS OUT Connector Routed Under Operator’s Seat FIGURE 7.
  • Page 28: Patriot 4420 - 2009 & Newer

    Route the opposite end of the cable out the fuse panel and around the back of the operator’s seat to the instructional seat compartment. Connect the CAN connector to the CAN connection on the node harness. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 29: Spx 4420 - 2008 & Older

    Cab Component Installation SPX 4420 - 2008 & Older Machine’s Existing CAN Connection FIGURE 11. Machine’s CAN Connection Existing CAN Connection or Terminator Locate the CAN connector outside the right-rear corner of the cab. Note: The connector will be labeled CAN Terminator. Disconnect the CAN connection or remove the terminator from the machine’s CAN connection.
  • Page 30: Spx 4410

    Route the 9-pin end of the cable out the fuse panel and around the back of the operator’s seat to the instructional seat compartment. Connect the 9-pin connector to the CAN connection on the node harness. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 31: Spx 4260

    If the CAN connector is not connected to anything: Connect the CAN connector to the mating 4-pin connector on the CAN extension cable. Leave the remaining 4-pin connector disconnected. This connection is not used in the SmarTrax system. Route the 9-pin end of the cable out the fuse panel and around the back of the operator’s seat to the instructional seat compartment.
  • Page 32 Plug the PS1 and PS2 connectors from the valve harness into the pressure transducers on the flow switch (P/N 334-0003-085). Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 33 Cab Component Installation Valve Harness Wiring Diagram FIGURE 18. Manual No. 016-5032-017 Rev. A...
  • Page 34: Calibrate The Smartrax System

    Refer to the SmarTrax and SmartSteer Calibration & Operation Manual (P/N 016-0171-277) for instructions on calibrating the SmarTrax system, adjusting system settings, and system operation. Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 35 Installing Fittings in the Flow Switch 11 Installing Fittings in the SmarTrax Valve 10 Installing the Left and Right Steering Hoses 13 Installing the Pressure Hose 15 Installing the SmarTrax Valve and Flow Switch 11 Installing the Tank Hose 15 Important Safety Information Electrical Safety 2...
  • Page 36 Index Case IH Patriot 4420 (2009 & Newer), SPX 4410/4420 (2008 & Older), SPX 4260 (S/N JFG003537 & Newer) SmarTrax™ Installation Manual...
  • Page 37 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If your dealer agrees with the warranty claim, the dealer will send the part and proof of purchase to their distributor or to Raven Industries for final approval.

Table of Contents