Raven SmarTrax Installation Manual
Case ih steiger and new holland t9.xxx - steering ready, model year 2016 & newer
Hide thumbs
Also See for SmarTrax:
- Calibration and operation manual (156 pages) ,
- Operation manual (73 pages) ,
- Installation manual (59 pages)
Subscribe to Our Youtube Channel
Related Manuals for Raven SmarTrax
Summary of Contents for Raven SmarTrax
- Page 1 Case IH Steiger and New Hol- land T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual P/N 016-5032-044 Rev. A 01/17 E28627 Copyright 2017...
-
Page 3: Table Of Contents
..............................12 Install the Foot Switch ......................12 Install the Chassis Cable - SmarTrax-Only Systems (If Applicable) ........13 Connect SmarTrax to an Existing Gen II Chassis Cable (If Applicable) ........15 Connect SmarTrax to an ISO VT Console Cable (If Applicable) .......... - Page 4 Table of Contents Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual...
-
Page 5: Important Safety Information
• Do not operate SmarTrax or any agricultural equipment while under the influence of alcohol or an illegal substance. • Remain in the operator’s position or a safe working distance away from the booms at all times when SmarTrax is engaged. -
Page 6: Hydraulic
• Deflection and backlash of belts and chains • Adjustment zones of adjustable brackets • Changes of position in steering and suspension systems Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual... -
Page 7: Electrical
IMPORTANT SAFETY INFORMATION • Moving linkages, cylinders, articulation joints, attachments • Ground engaging components For hose sections that move during machine operation: • Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or rubbing, especially in articulation and pivot points •... - Page 8 Remove visible surface water from components, connections, or seals using pressurized air or an aerosol electrical component cleaning agent. allow components to dry completely before reconnecting cables. Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual...
-
Page 9: Chapter 2 Introduction
FIGURE 1. Case IH Steiger Quadtrac535 PREPARING FOR INSTALLATION Before installing SmarTrax, park the machine where the ground is level, clean, and dry. Leave the machine turned off for the duration of the installation process. During the installation process, follow good safety practices. Be sure to carefully read the instructions in this manual as you complete the installation process. -
Page 10: Recommendations
Raven Industries recommends the following best practices before installing or operating the SmarTrax system for the first time, at the start of the season, or when moving the SmarTrax system to another machine: • Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic hoses, etc.). -
Page 11: Kit Contents
This section contains a list of the components that are included in the UltraGlide SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the SmarTrax kit with the components on this list. If you have questions about the kit, contact your local Raven dealer. - Page 12 Nut - M6 x 1.0 Lock 312-4000-207 Washer - 1/4” Split Lock 313-1000-016 Washer - 0.250” ID x 0.562” OD x 0.065” 313-2300-009 Thick Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual...
-
Page 13: Chapter 3 Cab Component Installation
CHAPTER C H A P T E R 3 INSTALLATION INSTALL THE SMARTRAX NODE MOUNT THE SMARTRAX NODE FIGURE 1. Instructional Seat Mounting Screws 1. Uninstall the instructional seat cushion by removing the screws that secure it to the frame. - Page 14 7. Secure the node mounting plate to the existing bolts in the floor of the cab using four 1/4” split lock washers (P/N 313-1000-016), four 1/4” flat washers (P/N 313-2300-009), and four M6 lock nuts (P/N 312-4000-207). Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual...
- Page 15 CAB COMPONENT INSTALLATION FIGURE 5. Node Cable Installed on Node 8. Install the two large, rectangular connectors of the node harness into the correct ports of the node, tightening the bolts on the connectors to secure the connections. NOTE: The connectors should be facing the window. 9.
-
Page 16: Node Mounting Locations
Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. • One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle travel, one arrow pointing straight up, and two of the arrows parallel to the ground. -
Page 17: Install The Chassis Cable - Smartrax-Only Systems (If Applicable)
Raven CAN versions of AutoBoom, product control, etc.), it is necessary to install the chassis power cable to operate the SmarTrax system. If a CAN system already exists on the machine, refer to Connect SmarTrax to an Existing Gen II Chassis Cable (If Applicable) below to connect power to the SmarTrax system. - Page 18 Connect the round connectors of the Viper 4 to ISOBUS cable (P/N 115-0172-421 - sold separately) to the mating ports on the back of the Viper 4. Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual...
-
Page 19: Connect Smartrax To An Existing Gen Ii Chassis Cable (If Applicable)
NOTE: The Gen II 6’ SmarTrax tee adapter cable (P/N 115-4001-071) and Viper 4 to ISOBUS cable (P/N 115- 0172-421) are sold separately. 1. Locate and disconnect the connection between the Raven console cable and chassis cable on the machine’s existing CAN system. - Page 20 7. Route the Viper 4 VT to SmarTrax adapter cable behind the trim in the rear of the cab. 8. Connect the TO AUX PORT connector of the Viper 4 VT to SmarTrax adapter cable to the mating connector on the Viper 4 to ISO VT adapter cable.
-
Page 21: Calibrate The Smartrax System
CAB COMPONENT INSTALLATION CALIBRATE THE SMARTRAX SYSTEM Refer to the SmarTrax Calibration & Operation Manual (P/N 016-0171-277) for instructions on calibrating the SmarTrax system, adjusting system settings, and system operation. P/N 016-5032-044 Rev. A... -
Page 22: System Diagrams
HAPTER SYSTEM DIAGRAMS Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual... - Page 23 CAB COMPONENT INSTALLATION P/N 016-5032-044 Rev. A...
- Page 24 HAPTER Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual...
- Page 25 Index Cab Component Installation Calibrating the SmarTrax System Connecting SmarTrax to an Existing Gen II Chassis Cable Installing the Foot Switch Installing the SmarTrax Node Mounting the Node 9 Node Mounting Locations 12 Electrical Safety Hydraulic Safety Important Safety Information...
- Page 26 Index Case IH Steiger and New Holland T9.XXX - Steering Ready, Model Year 2016 & Newer SmarTrax™ Installation Manual...
Need help?
Do you have a question about the SmarTrax and is the answer not in the manual?
Questions and answers