Page 1
Case IH Patriot 3230/3320/3330 - Steering Ready SmarTrax™ Installation Manual P/N 016-5032-013 Rev C 09/15 E22883 Copyright 2012, 2014, 2015...
Page 2
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine. WARNING • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. •...
CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized.
Preparing for Installation Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic system by loosening the hydraulic fittings slowly, where applicable.
Recommendations Raven Industries recommends the following best practices when installing or operating the SmarTrax system for the first time, at the start of the season, or when moving the SmarTrax system to another machine: • Install the GPS antenna in the recommended location. Refer to the following table for the machine-specific antenna mounting location.
This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
Page 10
TABLE 2. Picture Item Description Part Number Qty. Bracket - Node Mounting 107-0172-084 Standoff - M6 x 40 mm M/F,13 mm Hex 305-8000-008 Nut - 3/8”-16 UNC-3B Nylon Insert Lock 312-4000-061 Case IH Patriot 3230/3320/3330 - Steering Ready SmarTrax™ Installation Manual...
C ab Component CHAPTER C h a p t e r 3 Installation Install the Case IH Interface Box Locate and remove the panel behind the operator’s seat to access the existing Case steering control cables. Connect the steering control cables to the Case IH interface box (P/N 063-0173-038). Connect the round, 37-pin connector from the node harness (P/N 115-4001-032) to the 37-pin port of the Case interface box.
Page 14
Pull the node harness out and route it along the wall. Standoffs Installed FIGURE 3. Node Harness (P/N 115-4001-032) Reinstall the panel using the supplied standoffs (P/N 305-8000-008) to secure the panel on the top two studs. Case IH Patriot 3230/3320/3330 - Steering Ready SmarTrax™ Installation Manual...
Cab Component Installation Install the SmarTrax Node Node Installed on Mounting Plate FIGURE 4. Mount the SmarTrax node on the node mounting plate (P/N 107-0172-084) using three 3/8”-16 lock nuts (P/N 312-4000-061). Node Plate Installed on Panel FIGURE 5. Install the top of the node mounting plate on the installed standoffs and the bottom of the mounting plate on the machine’s studs using the machine’s nuts that were previously removed.
Page 16
Install the 18” CAN tee adapter cable (P/N 115-0172-068) between the machine’s CAN connectors. Route and connect the remaining end of the tee adapter cable to the node harness (P/N 115-4001-032) CAN connector. Case IH Patriot 3230/3320/3330 - Steering Ready SmarTrax™ Installation Manual...
Page 17
Cab Component Installation DGPS OUT Connector Routed Under Operator’s Seat FIGURE 8. Route the DGPS OUT connector out the right corner of the operator’s seat base and under the right arm rest. DGPS OUT Connected to Console Receiver Connection FIGURE 9. Console Console Receiver Cable...
Install the 6” sense adapter cable (P/N 115-0172-218) between the flow switch cable connection and the machine’s hydraulic valve. Go to www.ravenhelp.com > Software Updates > Guidance and Steering > SmarTrax™ and SmarTrax™ RTK to download software version 6.0.41. Follow the directions to update the SmarTrax software.
Enable Switch. FIGURE 12. A factory-installed switch is installed on the floor of the machine’s cab. Use this enable switch to engage and disengage the SmarTrax system after installation and calibration of the system is complete. Manual No. 016-5032-013 Rev. C...
Chapter 3 Calibrate the SmarTrax System Refer to the SmarTrax and SmartSteer Calibration & Operation Manual (P/N 016-0171-277) for instructions on calibrating the SmarTrax system, adjusting system settings, and system operation. Case IH Patriot 3230/3320/3330 - Steering Ready SmarTrax™ Installation Manual...
Page 21
Cab Component Installation Check the Machine’s Flow Switch Configuration 14 Enable Switch 15 Install the Phoenix 200 Antenna 15 Installing the Case IH Interface Box 9 Installing the SmarTrax Node 11 Important Safety Information Electrical Safety 2 Hydraulic Safety 2 Introduction...
Page 22
Index Case IH Patriot 3230/3320/3330 - Steering Ready SmarTrax™ Installation Manual...
Page 25
Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
Page 26
How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.
Need help?
Do you have a question about the SmarTrax and is the answer not in the manual?
Questions and answers