1. Manuals
  2. Brands
  3. Raven Manuals
  4. Farm Equipment
  5. SmarTrax
  6. Installation manual

Raven SmarTrax Installation Manual

Case ih patriot 4440, model year 2017 & newer - steering ready
Hide thumbs Also See for SmarTrax:
Table of Contents

Advertisement

Quick Links

Download this manual
Case IH Patriot 4440, Model
Year 2017 & Newer - Steering
Ready SmarTrax™ Installation
Manual
P/N 016-5032-041 Rev. A
10/16
E28538
Copyright 2016

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SmarTrax and is the answer not in the manual?

Questions and answers

Related Manuals for Raven SmarTrax

Summary of Contents for Raven SmarTrax

  • Page 1 Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual P/N 016-5032-041 Rev. A 10/16 E28538 Copyright 2016...

  • Page 2: Table Of Contents

    ......................7 Chapter 3 Cab Component Installation................11 Install the SmarTrax Node ....................... 11 Install the SmarTrax Node - Preferred Mounting Method ...................11 Install the SmarTrax Node - Secondary Mounting Method ................15 Node Mounting Locations ..............................20 Install the Flow Switch Adapter cable ..................21 Install the 600S GPS Receiver (If Applicable) .................
  • Page 3 Table of Contents Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...

  • Page 4: Important Safety Information

    Installation Manual. Failure to follow safety instructions may lead to equipment damage, personal injury, or death. • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened.

  • Page 5: Hydraulic Safety

    CAUTION HYDRAULIC SAFETY • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized.

  • Page 6: Chapter 2 Introduction

    FIGURE 1. Case IH Patriot 4440 PREPARING FOR INSTALLATION Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process.

  • Page 7: Point Of Reference

    The instructions in this manual assume that you are standing behind the machine, looking toward the cab. UPDATES Software and manual updates are available on the Raven Applied Technology website: http://www.ravenhelp.com Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...

  • Page 8: Kit Contents

    CASE IH PATRIOT 4440 WITHOUT 600S RECEIVER This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 9 Nut - 3/8” Zinc Flanged Lock 312-1001-164 Nut - 5/16”-18 x 7/8” Hex 312-1001-169 Nut - 1/4”-20 Nylon Insert Lock 312-4000-057 Nut - M6 Lock 312-4000-207 Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...

  • Page 10: Case Ih Patriot 4440 With 600S Gps Receiver

    INTRODUCTION TABLE 1. SmarTrax Kit (P/N 117-5032-041) Picture Item Description Part Number Qty. Washer - 1/4” Split Lock 313-1000-016 Washer - 0.250” ID x 0.562” OD x 0.065” 313-2300-009 Thick CASE IH PATRIOT 4440 WITH 600S GPS RECEIVER TABLE 2. SmarTrax Kit (P/N 117-5032-042)
  • Page 11 Bolt - 5/16”-18 x 7/8” Hex 311-0052-104 Nut - 3/8” Zinc Flanged Lock 312-1001-164 Nut - 5/16”-18 x 7/8” Hex 312-1001-169 Nut - 1/4”-20 Nylon Insert Lock 312-4000-057 Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...
  • Page 12 INTRODUCTION TABLE 2. SmarTrax Kit (P/N 117-5032-042) Picture Item Description Part Number Qty. Nut - M6 Lock 312-4000-207 Washer - 1/4” Split Lock 313-1000-016 Washer - 0.250” ID x 0.562” OD x 0.065” 313-2300-009 Thick P/N 016-5032-041 Rev. A...
  • Page 13 HAPTER Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...

  • Page 14: Chapter 3 Cab Component Installation

    C H A P T E R 3 INSTALLATION INSTALL THE SMARTRAX NODE INSTALL THE SMARTRAX NODE - PREFERRED MOUNTING METHOD FIGURE 1. Instructional Seat Mounting Screws 1. Uninstall the instructional seat cushion by removing the screws that secure it to the frame.
  • Page 15 4. Remove the plastic molding under the instructional seat by removing the nuts and bolts securing it. FIGURE 4. Node Mounted to Mounting Plate 5. Mount the SmarTrax node (P/N 063-0173-228) to the node mounting bracket (P/N 107-0172-084) using three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).
  • Page 16 CAB COMPONENT INSTALLATION FIGURE 5. Node Harness Installed on Node 8. Install the two large, rectangular connectors of the node cable (P/N 115-4001-247) into the correct ports of the node, tightening the bolts on the harness connectors to secure the connections. NOTE: The connectors should be facing the window.
  • Page 17 FIGURE 7. Convenience Tray Removed 13. Remove the convenience tray from the right-rear corner of the cab. 14. Locate the connectors labeled POWER GND PORT and RAVEN INTERFACE on the machine’s harness in the convenience tray compartment and route them to the node harness.

  • Page 18: Install The Smartrax Node - Secondary Mounting Method

    CAB COMPONENT INSTALLATION INSTALL THE SMARTRAX NODE - SECONDARY MOUNTING METHOD FIGURE 9. Node Mounting Location 1. Identify the node mounting location on the bracket to the right of the operator’s seat. 2. If equipped with a traction control foot pedal, remove the existing nut, bolt, and spacer from the bracket that holds the pedal in place.
  • Page 19 8. Install two 5/16”-18 x 7/8” hex bolts (P/N 311-0052-104) and two 5/16” zinc flanged lock nuts (P/N 312-1001-169) in the top and right node mounting tabs. Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...
  • Page 20 NOTE: The mounting plate must be within +/- 2° of level to the wall for the SmarTrax system to operate properly 10. Secure the node support bracket to the node mounting bracket by inserting a 5/16"-18 x 7/8" hex bolt (P/N 311-0052-104) through both brackets and installing one 5/16”...
  • Page 21 FIGURE 16. Node Harness Routing 13. Route the node harness into the blower fan compartment located in the right-rear corner of the cab. Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...
  • Page 22 FIGURE 17. Convenience Tray Removed 14. Remove the convenience tray from the right-rear corner of the cab. 15. Locate the connectors labeled POWER GND PORT and RAVEN INTERFACE on the machine’s harness in the convenience tray compartment and route them to the node harness.

  • Page 23: Node Mounting Locations

    Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. • One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle travel, one arrow pointing straight up, and two of the arrows parallel to the ground.

  • Page 24: Install The Flow Switch Adapter Cable

    2. Disconnect the flow switch cable from the flow switch that is connected to the machine’s steering valve. 3. Install the 6” sense adapter cable (P/N 115-0172-218) between the flow switch cable connection and the machine’s hydraulic valve. NOTE: During the SmarTrax calibration process, select preset CIH SPX 4430 2014. P/N 016-5032-041 Rev. A...

  • Page 25: Install The 600S Gps Receiver (If Applicable)

    5. Connect the CASE GPS connection of the 600S to Case IH box interface cable to the DGPS IN connection of the node harness (P/N 115-4001-247). Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...

  • Page 26: Enable Switch

    SmarTrax system after installation and calibration of the system is complete. CALIBRATE THE SMARTRAX SYSTEM Refer to the SmarTrax Calibration & Operation Manual (P/N 016-0171-277) for instructions on calibrating the SmarTrax system, adjusting system settings, and system operation.
  • Page 27 HAPTER Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...
  • Page 28 Index Cab Component Installation Calibrating the SmarTrax System Enable Switch Install the 600S GPS Receiver Install the Flow Switch Adapter Cable Installing the SmarTrax Node Important Safety Information Electrical Safety Hydraulic Safety Introduction Kit Contents Case IH Patriot 4440 with 600S Receiver 7...
  • Page 29 Index 26 Case IH Patriot 4440, Model Year 2017 & Newer - Steering Ready SmarTrax™ Installation Manual...

Table of Contents