1. Manuals
  2. Brands
  3. Raven Manuals
  4. Farm Equipment
  5. SmarTrax
  6. Installation manual

Raven SmarTrax Installation Manual

Case ih tital 3030 and 3530 - model year 2013 & newer
Hide thumbs Also See for SmarTrax:
Table of Contents

Advertisement

Quick Links

Download this manual
Case IH Tital 3030 and 3530 - Model
Year 2013 & Newer
SmartTrax™ Installation Manual
P/N 016-4001-126 Rev B
06/15
E23433
Copyright 2013, 2014

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SmarTrax and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Raven SmarTrax

Summary of Contents for Raven SmarTrax

  • Page 1 Case IH Tital 3030 and 3530 - Model Year 2013 & Newer SmartTrax™ Installation Manual P/N 016-4001-126 Rev B 06/15 E23433 Copyright 2013, 2014...
  • Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.

  • Page 3: Table Of Contents

    Cab Component Installation ..........19 Install the SmarTrax Node ....................... 19 Node Mounting Locations ....................19 Install the SmarTrax Node - Preferred Mounting Method ..........20 Mount the SmarTrax Node - Secondary Mounting Method ..........24 Install the Foot Switch ......................
  • Page 4 Table of Contents Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...

  • Page 5: Important Safety Information

    Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine. WARNING • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. •...

  • Page 6: Hydraulic Safety

    CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized.

  • Page 7: Introduction

    Preparing for Installation Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic system by loosening the hydraulic fittings slowly, where applicable.

  • Page 8: Recommendations

    Recommendations Raven Industries recommends the following best practices when installing or operating the SmarTrax system for the first time, at the start of the season, or when moving the SmarTrax system to another machine: • Install the GPS antenna in the recommended location. Refer to the following table for the machine-specific antenna mounting location.

  • Page 9: Kit Contents

    This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 10 Screw - #10 x 3/4” Slotted Head Self-Tapping 311-0001-321 Bolt - 1/4”-20 x 1-1/4” Hex 311-0050-106 Bolt - 5/16”-18 x 7/8” Hex 311-0052-104 Bolt - 3/8”-16 x 1” Hex 311-0054-105 Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 11 Introduction SmarTrax Installation Kit (P/N 117-4001-126) TABLE 1. Picture Item Description Part Number Qty. Nut - 3/8”-16 312-1001-037 Nut - 3/8” Zinc Flanged Lock 312-1001-164 Nut - 5/16”-18 x 7/8” Hex 312-1001-169 Nut - 1/4”-20 Nylon Insert Lock 312-4000-057 Nut - M6 Lock 312-4000-207 Washer - 1/4”...
  • Page 12 Hydraulic Hose - -4 ORFS (F) to -6 ORFS (F) 214-1000-665 - 50” Hydraulic Hose - -8 ORFS (F) 90° to -6 214-1000-778 ORFS (F) - 40” Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...

  • Page 13: Hydraulic System Installation

    WARNING Hydraulics are under pressure. Care should always be taken with a system that has been pressurized. Before beginning the SmarTrax hydraulic installation, turn off the machine and relieve pressure by turning the steering wheel left and right. Never work on a hot machine. Always allow it to cool before performing diagnostics, maintenance, or routine service.

  • Page 14: Install Fittings In The Smartrax Valve

    Install Fittings in the SmarTrax Valve Before mounting the SmarTrax valve (P/N 063-0131-129) on the machine, install the proper fittings in the valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure.

  • Page 15: Mount The Smartrax Valve

    Using the holes in the hydraulic valve mounting bracket (P/N 107-0171-907) as a template, drill 5/16” holes in the machine’s walkway support. Secure the SmarTrax valve (P/N 063-0131-129) to the hydraulic valve mounting bracket (P/N 107-0171- 907) using four 5/16”-18 x 7/8” hex bolts (P/N 311-0052-104) and four 5/16”-18 lock washers (P/N 313- 1000-019).

  • Page 16: Install The Left And Right Steering Hoses

    Left Steering Hose Installed on SmarTrax Valve FIGURE 5. Connect the straight end of the installed hydraulic hose to the fitting installed in Port A of the SmarTrax valve. Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 17 ORFS M/F 45° swivel elbow fitting (P/N 333-0012-102) on the installed tee fitting to achieve the connection. Right Steering Hose Installed on SmarTrax Valve FIGURE 7. Connect the straight end of the installed hydraulic hose to the fitting installed in Port B of the SmarTrax valve. Manual No. 016-4001-126 Rev. B...

  • Page 18: Install The Pressure And Tank Hoses

    Pressure Hose Installed on SmarTrax Valve FIGURE 9. Connect the straight end of the installed hydraulic hose to the fitting installed in Port P of the SmarTrax valve. Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 19 ORFS M/F 45° swivel elbow fitting (P/N 333-0012-102) on the installed tee fitting to achieve the connection. Tank Hose Installed on SmarTrax Valve FIGURE 11. Connect the straight end of the installed hydraulic hose to the fitting installed in Port T of the SmarTrax valve. Manual No. 016-4001-126 Rev. B...

  • Page 20: Install The Load Sense Hoses

    Install the male end of the supplied hydraulic hose (P/N 214-1000-464) on the end of the machine’s load sense hose. Connect the female end of the installed hydraulic hose to the fitting installed in Port LSPV on the SmarTrax valve.

  • Page 21: Hydraulic Diagram

    Hydraulic System Installation Hydraulic Diagram Manual No. 016-4001-126 Rev. B...
  • Page 22 Chapter 3 Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...

  • Page 23: Cab Component Installation

    Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. • One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle travel, one arrow pointing straight up, and two of the arrows parallel to the ground.

  • Page 24: Install The Smartrax Node - Preferred Mounting Method

    Remove any contents from under the instructional seat. Floor Mat Removed from Cab FIGURE 3. Lift the floor mat from the floor in front of the seat. Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 25 Node Mounted to Mounting Plate FIGURE 5. Mount the SmarTrax node (P/N 063-0173-228) to the node mounting bracket (P/N 107-0172-084) using three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). Place the node in the instructional seat compartment so the connectors face away from the operator’s seat.
  • Page 26 DGPS OUT Connector Routed Under Operator’s Seat FIGURE 7. Route the DGPS OUT connector out the right corner of the operator’s seat base and under the right arm rest. Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 27 Cab Component Installation Convenience Tray Removed FIGURE 8. Remove the convenience tray from the right-rear corner of the cab. Locate the connectors labeled POWER GND PORT and PRODUCT CAN on the machine’s harness in the convenience tray compartment. Connect the machine’s POWER GND PORT connector to the mating 6-pin POWER connector on the node harness.

  • Page 28: Mount The Smartrax Node - Secondary Mounting Method

    Align the hole in the node mounting bracket (P/N 107-0171-954) with the hole in the machine’s bracket. Using the node mounting bracket as a template, drill a second hole in the machine’s bracket. Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 29 Cab Component Installation Node Mounting Bracket Installed FIGURE 12. Secure the node mounting bracket to the machine’s bracket using two 1/4”-20 x 1-1/4” hex bolts (P/N 311- 0050-106), two 1/4” flat washers (P/N 313-2300-009), and two 1/4”-20 nylon insert lock nuts (P/N 312-4000- 057).
  • Page 30 Node Support Bracket Secured to Cab Floor FIGURE 15. Secure the node support bracket to the cab floor using one #10 x 3/4” self-tapping slotted hex head screw (P/N 311-0001-321). Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 31 Cab Component Installation Node Harness Installed on Node FIGURE 16. Install the two large, rectangular connectors of the node harness (P/N 115-4001-196) into the correct ports of the node, tightening the bolts on the harness connectors to secure the connections. Locate the ENABLE connector on the node harness and connect it to the foot switch cable connector.

  • Page 32: Install The Foot Switch

    Using the holes in the foot switch as a template, drill holes in the floor of the cab. Secure the foot switch to the floor by installing the supplied screws in each of the mounting holes. Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...

  • Page 33: Install The Valve Harness

    Connect the rectangular 12-pin connector on the valve harness into the mating connection of the node harness (P/N 115-4001-196). Connect the PSI connector to the transducer (P/N 422-0000-086) installed in Port PS of the SmarTrax valve (P/N 063-0131-139). Manual No. 016-4001-126 Rev. B...
  • Page 34 Connect the DOUBLE BLOCKER 2 connector to Port 1B of the SmarTrax valve. Connect the LEFT connector to the bottom coil of the stack on the SmarTrax valve. Connect the RIGHT connector to the top coil of the stack on the SmarTrax valve.
  • Page 35 Cab Component Installation Valve Harness Wiring Diagram FIGURE 23. Manual No. 016-4001-126 Rev. B...

  • Page 36: System Diagrams

    Chapter 4 System Diagrams Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 37 Cab Component Installation Manual No. 016-4001-126 Rev. B...
  • Page 38 Chapter 4 Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...

  • Page 39: Startup Procedures

    Turn the machine’s wheels fully from side to side repeatedly to remove air from the hydraulic system. Note: During the SmarTrax system installation, whenever the hydraulic system is purged for maintenance, or when fittings are loosened or disconnected, air is introduced into the lines of the hydraulic system.

  • Page 40: Calibrate The Smartrax System

    Raven console. Note: If there are issues with the SmarTrax system, turn off the machine and correct them immediately. For additional assistance, refer to the SmarTrax and SmartSteer Calibration & Operation Manual (P/N 016-0171-277) or contact your local Raven dealer.
  • Page 41 Secondary Mounting Method 24 Installing the Valve Harness 29 Hydraulic Installation Hydraulic Diagram 17 Installing Fittings in the SmarTrax Valve 10 Installing the Left and Right Steering Hoses 12 Installing the Load Sense Hoses 16 Installing the Pressure and Tank Hoses 14...
  • Page 42 Index Case IH Titan 3030 and 3530, Model Year 2013 & Newer SmarTrax™ Installation Manual...
  • Page 45 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
  • Page 46 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.

Table of Contents