Table of Contents
Advertisement
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
3. By iLead controller ( please refer to the user guide of iLead ) or universal DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address
setting will be effected at once. Every time you turn the unit on, it will show IM-5S/IM-5W on
the display and move all the motors to their 'home' position and you may hear some noises
for about 20 seconds. After that the unit will be ready to receive DMX signal or run the built
in programs.
5.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other
units to give an automatic, sound activated, synchronized light show. This function
is good when you want an instant show. You have to set the first unit in master
mode
and select
(show 1) or
or
(show 4) mode. Its DMX input jack will have nothing plugged into it, and
Its master LED will be constantly on and sound LED will flash to the music. The
other units will have to set in slave mode
(2 light show) mode, Their DMX cables plugged into the DMX input jacks
(daisy chain) and the slave led lights will constantly on.
2-light show
In
(slave mode),
means the unit works normally and
2-light show. In order to create a great light show, you can set
get contrast movement to each other, even if you have two units only.
5.2 Easy Controller
The easy remote control is used only in master/slave mode. By
connecting to the 1/4" microphone jack of the first unit, you will find
that the remote control on the first unit will control all the other units
functions press the MENU button again.
(show 2) or
(show 3)
and select
(normal) or
means
on the second unit to
12J
Stand by
Blackout the unit
Strobe
1.Gobo / Color
sync.
Function
strobe
Move
2.Sync. strobe
Spot
3.Two-light strobe
Sound 1
Mode
(LED off )
Stand by
Blackout the unit
Strobe
1.Color sync.
strobe
Function
2.Sync. strobe
Move
3.Two-light strobe
Wash
Sound 1
Mode
(LED off )
5.3.1 iSolution Operation
♦
Consistent DMX configuration enable iMove to be linked together with iRock and iShow
and controlled at the same time.
♦
DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦
Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
following diagram to address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.
X/Y moving show
Color/Gobo
X/Y moving setting
mode selection
selection
1.Pan position
( Show 1 ~ Show
1. Hold on for gobo
2.Tilt position
4 )
change.
First set Master
Please refer to
2. Press shortly for
unit, then set Slave
Show mode in
color change
units' position
4.2 Main Function
Sound 2
Slow/Sound 3
Position/ Latch
(LED normal
(LED on)
(LED fast blinking)
blinking)
X/Y moving show
Color selection
X/Y moving setting
mode selection
1.Pan position
( Show 1 ~ Show
2.Tilt position
4 )
3.Dimmer
Please refer to
First set Master
Show mode in
unit, then set Slave
4.2 Main Function
units' position
Sound 2
Slow/Sound 3
Position/ Latch
(LED normal
(LED on)
(LED fast blinking)
blinking)
is showing on the display. Pressing ENTER
13J
Advertisement
Table of Contents
