Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ACME AE-610 BEAM
Summary of Contents for ACME AE-610 BEAM
-
Page 1: User Manual
AE-610 BEAM User Manual Please read the instruction carefully before use... -
Page 2: Table Of Contents
TABLE OF CONTENTS 1. Safety Instruction ................... 2 2. Technical Specification ................4 3. Description ..................... 5 3.1 Control Panel .................. 5 4. How To Set The Unit................5 4.1 Main Function ................. 5 4.2 Home Position Adjustment ............10 4.3 Error Information ................ -
Page 3: Safety Instruction
1. Safety Instruction Please read carefully the instruction manual, which includes important information about the installation, usage and maintenance. WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction manual. Important: Damages caused by the disregard of this user manual are not subject to warranty. - Page 4 Do not operate in dirty or dusty environment; do clean the fixture regularly. Do not touch any wire during operation as there might be a hazard of electric shock. Avoid power wires twist other cables. The minimum distance between light output and the illuminated surface must be more than ...
-
Page 5: Technical Specification
2. Technical Specification DMX Channels: 12 channels Control mode: DMX, Master slave, Sound active LCD display easy to control One gobo wheel One color wheel Smooth 0~100% dimming and variable strobe speeds Voltage: AC 100~240V, 50/60Hz ... -
Page 6: Description
3. Description 3.1 Control Panel 1. Button: MENU To select the programming functions DOWN To go forward in the selected functions To go backward in the selected functions ENTER To confirm the selected functions 2. Microphone: To receive music for sound active; 3. -
Page 8: Dmx Address
DMX Address To select DMX Address, press the ENTER button to show the DMX ADDRESS on the display. Use the UP/DOWN button to adjust the address from 001 to 512. Once the address has been selected, press the ENTER button to setup, to go back to the functions without any change press the MENU button again. - Page 9 minute to exit the menu mode. Sound Sense To select Sound Sense, press the ENTER button to show the SOUND SENSE on the display. Use the DOWN/UP button to adjust the value from 0 to 100. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any change press the MENU button again.
-
Page 10: Firmware Version
Fixture Time To select Fixture Time, press the ENTER button and the display will show the number of working hours of the unit. To go back to the functions press the MENU button again. Press and hold the MENU button about one second or wait for one minute to exit the menu mode. Lamp Time To select Lamp Time, press the ENTER button and the display will show the number of working hours of the lamp. -
Page 11: Home Position Adjustment
Reset To select Reset, press the ENTER button and all channels of the unit will return to their standard position. 4.2 Home Position Adjustment Press the MENU button for at least 3 seconds then press the ENTER button for at least 5 seconds into offset mode to adjust the home position for the motors. -
Page 12: Error Information
To select the Color Offset, press the ENTER button to show the COLOR OFFSET on the display. Use the DOWN and UP button to adjust the value from -127 to 127, press the ENTER button to store. Press the MENU button to exit. GOBO OFFSET —Gobo home position adjustment To select the Gobo 1 Offset, press the ENTER button to show the GOBO OFFSET on the display. -
Page 13: Control By Universal Dmx Controller
CPU-B Error, CPU-C Error, CPU-D Error They appear when board P.C or some wires are damaged. Pan Reset Error, Pan Encode Error, Tilt Reset Error, Tilt Encode Error, Shutter Reset Fail, Dimmer Reset Fail, Color Reset Fail, Gobo Reset Fail, Focus Reset fail. They may appear when turning on or resetting the unit, for some parts such as board P.C are damaged. -
Page 14: Address Setting
easily distort the signal and shut down the system. 3. The DMX output and input connectors are pass-through to maintain the DMX circuit, when one of the units’ power is disconnected. 4. Each lighting unit needs to have a DMX address to receive the data by the controller. The address number is between 0-511 (usually 0 &... - Page 15 000-255 TILT FINE PAN/TILT SPEED 000-255 fast slow DIMMER 000-255 0%~100% STROBE: 000-007 Standby 008-015 Open 016-131 Strobe: Slow Fast 132-139 Open 140-181 Fast Close Slow Open 182-189 Open 190-231 Fast Open Slow Close 232-239 Open 240-247 Random Strobe 248-255 Open COLOR:...
- Page 16 040-043 Gobo10 044-047 Gobo11 048-051 Gobo12 052-055 Gobo13 056-059 Gobo14 060-063 Gobo15 064-068 Gobo1 Shaking 069-072 Gobo2 Shaking 073-076 Gobo3 Shaking 077-080 Gobo4 Shaking 081-084 Gobo5 Shaking 085-089 Gobo6 Shaking 090-093 Gobo7 Shaking 094-097 Gobo8 Shaking 098-101 Gobo9 Shaking 102-105 Gobo10 Shaking 106-110 Gobo11 Shaking...
-
Page 17: Troubleshooting
250-255 Sound Function 6. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The unit does not work, no light and the fan does not work 1. Check the connect power and main fuse. 2. -
Page 18: Maintenance And Cleaning
7. Maintenance and Cleaning Maintenance: Ballast A. As the pictures shown above, please replace the cable or cable joints immediately once they’ve turned yellow. B. Do maintain the fixtures every two months and make sure that all the screws and terminals have been locked firmly to make sure the normal performance of the fixtures. -
Page 19: Declaration Of Conformity
Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55103-1: 2009+A1:2012; EN55103-2: 2009; EN61000-3-2: 2014; EN61000-3-3: 2013. & Harmonized Standard EN 60598-1:2015;... - Page 20 Innovation, Quality, Performance...