Related Manuals for ACME FURY LED RGB
Summary of Contents for ACME FURY LED RGB
-
Page 1: User Manual
FURY LED RGB RAGE LED RGB LED-3082 RGB LED-3084 RGB User Manual Please read the instructions carefully before use... -
Page 2: Table Of Contents
TABLE OF CONTENTS 1. Safety Instructions 2. Technical Specifications 3. Installation 4. How to set the unit 5. How to control the unit 6. DMX 512 Configuration 7. DMX 512 Connections 8. Troubleshooting 9. Fixture Cleaning... - Page 3 Safety Introductions Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet. ...
-
Page 4: Technical Specifications
2. Technical Specifications Fitted with 2 x 3W tri-color LEDs, the DMX Fury/Rage LED fills the entire room with powerful and laser-like muticolor beams, delivering fabulous effects. Great built-in lighting shows under Master/Slave and Sound Active Full range dimmer and variable strobe effects. ... -
Page 5: How Toset The Unit
4. How toset the unit 4.1Rear Panel ○ 1 Display: To show the various menus and the selected functions LED: ○ 2 DMX DMX input present ○ 3 MASTER Master Mode ○ 4 SLAVE Slave Mode ○ 5 SOUND Flashing Sound activation Button: ○... - Page 6 4.2 Main Function To select any functions, press MENU button until the required one is shown on the display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to change the mode. Once the required mode has been selected, press ENTER button to setup or it will automatically return to the main functions without any change after idling 30 seconds.
- Page 7 Channel Mode Press the MENU button up to when the is shown on the display. Pressing ENTER button, Use DOWN and UP button to select the (1 channel) or channels ) mode. Once select, press the ENTER button to setup or automatically exit menu mode without any change after 30 seconds.
- Page 8 button. LED display Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select (display on) or (display off) mode. Once select, press ENTER button to setup or exit menu mode without any change after 30 seconds.
-
Page 9: How To Control The Unit
4.3 Home Position Adjust Press Enter button for about 5 seconds, “OPAN” will shown on the display, press ENTER button to confirm, then use DOWN and UP button to adjust the home position (-127 - 127) of the motor. Once the position has been selected, press the ENTER button to setup or exit the offset mode without any change press the MENU button. - Page 10 5.2 Easy Controller (by CA-8) The easy remote control is used only in master/slave mode. By connecting to the 1/4” microphone jack of the first unit, you will find that the remote controller on the first unit will control all the other units for Stand by, Function and Mode selection Blackout Blackout the unit Select Speed...
-
Page 11: Dmx512 Configuration
6. DMX512 Configuration 1 & 3-CH modes:... -
Page 12: Dmx512 Connections
7. DMX512 Connections The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable. -
Page 13: Troubleshooting
8. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 1. Check the connection of power and main fuse. 2. Measure the mains voltage on the main connector. B. -
Page 14: Fixture Cleaning
9. Fixture Cleaning The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics. ... - Page 15 EC - Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002; EN61000-4-4: 1995;...
- Page 16 Innovation, Quality, Performance...