ACME PAGEANT 300ZR User Manual
  1. Manuals
  2. Brands
  3. ACME Manuals
  4. DJ Equipment
  5. PAGEANT 300ZR
  6. User manual

ACME PAGEANT 300ZR User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CM-300ZR II
User Manual
Please read the instruc on carefully before use

Advertisement

Table of Contents
loading

Related Manuals for ACME PAGEANT 300ZR

Summary of Contents for ACME PAGEANT 300ZR

  • Page 1 CM-300ZR II User Manual Please read the instruc on carefully before use...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS 1. Safety Instructions ....................2 2. Technical Specifications ..................3 3. How To Set The Unit ....................4 3.1 Control Panel ....................4 3.2 Main Function ....................5 3.3 Home Position Adjust ..................13 4. Control By Universal DMX Controller ..............13 4.1 DMX 512 Connection ..................

  • Page 3: Safety Instructions

    1. Safety Instructions Please read the instruction carefully which includes important information about the installation, usage and maintenance. WARNING Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. ...

  • Page 4: Technical Specifications

    moisture.  The housing and lenses must be replaced if they are visibly damaged. Caution: There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer.

  • Page 5: How To Set The Unit

     LED Source: 19 × 15W RGBW LED  Weight: 9.0Kgs  Dimension: 325 × 189 × 393mm 3. How To Set The Unit 3.1 Control Panel 10 11 LED: 1. POWER Power On 2. DMX DMX input present 3. Display: Shows the various menus and the selected functions 4.

  • Page 6: Main Function

    To go forward in the selected functions ENTER To confirm the selected functions 5. DMX input: DMX512 link, use 5-pin XLR cable to link the unit and DMX controller 6. DMX input: DMX512 link, use 3-pin XLR cable to link the unit and DMX controller 7.
  • Page 7 DMX Address DMX Functions DMX Channel Mode View DMX Value Pan Inverse Tilt Inverse P/T Feedback Bl.o. P/T Moving Fixture Setting White Balance Auto Cooling Mode Linear Square Law Dimmer Curve Inverse Squ. S-curve Fast Dimmer Speed MENU Smooth Display Inverse Backlight Auto Off Display Setting Backlight Intensity...
  • Page 8 DMX Functions Enter MENU mode, select DMX Functions, press the ENTER button to confirm, use the UP/DOWN button to select DMX Address, DMX Channel Mode or View DMX Value. DMX Address To select DMX Address, press the ENTER button to show the DMX ADDRESS on the display. Use the UP/DOWN button to adjust the address from 001 to 512, press the ENTER button to setup.
  • Page 9 P/T Feedback To select P/T Feedback, press the ENTER button to show the PAN/TILT FEEDBACK on the display. Use the UP/DOWN button to select No (Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while pan/tilt out of step), press the ENTER button to setup. Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.
  • Page 10 Linear: The increase in light intensity appears to be linear as DMX value is increased. Square Law: Light intensity control is finer at low levels and coarser at high levels. Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels. S-cure: Light intensity control is finger at low levels and high levels and coarser at medium levels.
  • Page 11 Backlight Intensity To select Backlight Intensity, press the ENTER button to show the BACKLIGHT INTENSITY on the display. Use the UP/DOWN button to adjust the intensity from 1 (dark) to 10 (bright). Once selected, press the ENTER button to setup and store. Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.
  • Page 12 Press the ENTER button, and then use the UP/DOWN button to select channel, and adjust the channel value. Once selected, press the ENTER button to setup, the fixture will run as the channel value indicates. Press the MENU button back to the last menu or exit menu mode let the unit idle one minute.
  • Page 13 To select All, press the ENTER button to show the ALL on the display. Use the UP/DOWN button to select Yes (the unit will run built-in program to reset all motors to their home positions) or No, press ENTER button to store. Press MENU button to exit menu mode. Special Functions Enter MENU mode, select Special Functions, press the ENTER button to confirm, use the UP/DOWN button to select Fixture Maintenance or Factory Setting.

  • Page 14: Home Position Adjust

    3.3 Home Position Adjust In the main functions, hold the ENTER button for at least 3 seconds into offset mode, use the DOWN/UP button up to select Pan Offset, Tilt Offset or Zoom Offset, and press the ENTER button to confirm. Use the DOWN/UP button to adjust the home position of the Pan, Tilt or Zoom, Once the position has been selected, press the ENTER button to setup, to go back to the functions without any change press the MENU button again.

  • Page 15: Address Setting

    1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable. 2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit.

  • Page 16: Dmx 512 Configuration

    Please refer to the following diagram to address your DMX512 channel for the first 4 units： Unit 1 Unit 2 Unit 3 Unit 4 Channel mode Address Address Address Address 14 channels 26 channels 30 channels 4.3 DMX 512 Configuration 14 Channels Mode(Mode 1): CHANNEL VALUE...
  • Page 17 145-149 Open 150-164 Strobe 6: random closing pulse, fast slow 165-169 Open 170-184 Strobe 7: burst pulse, fast slow 185-189 Open 190-204 Strobe 8: random burst pulse, fast slow 205-209 Open 210-224 Strobe 9: sine wave, fast slow 225-229 Open 230-244 Strobe 10: burst, fast slow 245-255...
  • Page 18 204-210 Color 27 211-217 Color 28 218-225 Color 29 226-232 Color 30 233-240 Color 31 241-247 Color 32 248-255 Color 33 ZOOM 000-255 wide  narrow 26 Channels Mode(mode 2): CHANNEL VALUE FUNCTION 000-255 000-255 PAN FINE 000-255 TILT 000-255 TILT FINE PAN/TILT SPEED 000-255...
  • Page 19 165-169 Open 170-184 Strobe 7: burst pulse, fast slow 185-189 Open 190-204 Strobe 8: random burst pulse, fast slow 205-209 Open 210-224 Strobe 9: sine wave, fast slow 225-229 Open 230-244 Strobe 10: burst, fast slow 245-255 Open 000-255 RING 1 RED (0%  100%) 000-255 RING 1 GREEN (0% ...
  • Page 20 218-225 Color29 226-232 Color30 233-240 Color31 241-247 Color32 248-255 Color33 000-255 RING 2 RED (0%  100%) 000-255 RING 2 GREEN (0%  100%) 000-255 RING 2 BLUE (0%  100%) 000-255 RING 2 WHITE (0%  100%) RING 2 COLOR PRESET 000-255 (The same as CH14：RING 1 COLOR PRESET) 000-255...
  • Page 21 30 Channels Mode (mode 3): CHANNEL VALUE FUNCTION 000-255 000-255 PAN FINE 000-255 TILT 000-255 TILT FINE PAN/TILT SPEED 000-255 fast  slow ZOOM 000-255 wide  narrow SPECIAL FUNCTIONS 000-009 No function 010-014 Reset 015-255 No function DIMMER 000-255 0%~100% SHUTTER 000-019...
  • Page 22 000-255 RING 1 BLUE (0%  100%) 000-255 RING 1 WHITE (0%  100%) RING 1 COLOR PRESET 000-009 Open 010-017 Color1 018-024 Color2 025-032 Color3 033-039 Color4 040-047 Color5 048-054 Color6 055-061 Color7 062-069 Color8 070-076 Color9 077-084 Color10 085-091 Color11 092-099...
  • Page 23 000-255 RING 3 RED (0%  100%) 000-255 RING 3 GREEN (0%  100%) 000-255 RING 3 BLUE (0%  100%) 000-255 RING 3 WHITE (0%  100%) RING 3 COLOR PRESET 000-255 (The same as CH14：RING 1 COLOR PRESET) RING COLOR MACRO 000-007 Blackout...

  • Page 24: Troubleshooting

    112-135 Macro 5 136-159 Macro 6 160-183 Macro 7 184-207 Macro 8 208-231 Macro 9 232-255 Macro 10 RING COLOR MACRO 4 000-015 Macro 1 016-027 Macro 2 028-039 Macro 3 040-051 Macro 4 052-063 Macro 5 064-075 Macro 5 076-087 Macro 6 088-099...

  • Page 25: Fixture Cleaning

    B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly. 2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
  • Page 27 Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 2004/108/EC. EN55103-1: 2009 ; EN55103-2: 2009; EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008. &...
  • Page 28 Innovation, Quality, Performance...

This manual is also suitable for:

Cm-300zr iiCm-350z ii

Table of Contents