Extron electronics FOX3 T 301 User Manual page 39

Command Function
Transmitter and Receiver (continued)
RS-232 COMM settings
Set serial port parameters
X1@
KEY: = Baud rate
X1#
= Parity
X1$
= Data bits
X1%
= Stop bits
X1^
= UARTs
Resets
Erase all files from flash memory
Reset unit settings
Absolute system reset (retain IP)
Absolute system reset
IP system reset
Reset audio gain and attenuation
Global unsolicited response
Input change
Fiber link
Input video signal presence
Input HDCP
Output HDCP
Audio input status
X$
KEY: = Input video signal status
X%
= Display input audio status
X^
= Input HDCP status
X&
= Output HDCP status
X1*
= Active fiber link
X2*
= Fiber Link detection (SPF A/B IN LED)
NOTE: SFP A and SFP B OUT LED is always active
Transmitter only (common)
HDCP authorized device
Set HDCP authorized device on
Set HDCP authorized device off
View HDCP authorized device
X1(
KEY: = Input HDCP Authorization
Input audio selection
Select audio input
View selected audio input
X*
KEY: = Input audio selection
SIS Command
(Host to Unit)
EX1^ X1@ X1# X1$ X1% }
* , , , CP
300 15200 9600
default)
− baud (
o e n m s
dd, ven, one (default), ark,
7 8
, (default)
1 2
(default),
1
= endpoint
E }
ZFFF
E }
ZXXX
E }
ZY
E }
ZQQQ
E }
1ZQQQ
E }
ZA
0
= Not detected
0
= Not detected
0
= No source detected
3
= Source with no HDCP present
0
= No active sink detected
2
= Sink detected, output not encrypted
1
= SFP A
0
= Not detected
E }
E1HDCP
E }
E0HDCP
E }
EHDCP
Verbose mode 2/3:
0
= HDCP authorized off
E I X* AFMT }
E IAFMT }
0
= Auto (default)
FOX3 T/R 301/311 Transmitters and Receivers • SIS Configuration and Control
Response
(Unit to Host)
X1^ X1@ X1# X1$
Cpn Ccp , , ,
•
pace (only the first letter required)
]
Zpf
]
Zpx
]
Zpy
]
Zpq
]
Zpq1
]
Zpa
]
Reconfig
X1* X2*]
Sts02* *
X$]
SigI
X^]
HdcpI
X&]
HdcpO
X%]
Sts05*
1
= Detected
1
= Detected
2
= Source with HDCP detected
1
= Sink detected, output encrypted
2
= SFP B
1
= Detected
]
HdcpE1
]
HdcpE0
X1(]
X1(]
HdcpE
1
= HDCP authorized on (default)
AfmtI X*]
X*]
1 2
= Digital
Additional description
X1%]
Removes files created in user space.
Resets unit to factory default.
E
Same as ZQQQ except excludes IP
settings.
Master Reset, resets IP address and
subnet mask to default. Also resets all
installed cards.
Resets only IP settings.
Reset audio gain & attenuation to default
levels.
Any change of the input frequency, during
module install, or a power cycle.
Any change in fiber link status.
Any change in input signal status.
Any change in input HDCP status.
Any change in output HDCP status.
Displays input audio selection status.
Default: HDCP authorized on.
Default. Digital has priority.
= Analog
31