DWU851 (DD1-WU70P/71P) DHD851 (DD1-HD70P/71P) SERVICE MANUAL DWX851 (DD1-WX70P/71P) Warning The technical information and parts shown in this manual are not to be used for: the development, design, production, storage or use of nuclear, chemical, biological or missile weapons or other weapons of mass destruction;...
Page 3
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) CAUTION FOR SAFETY Entries with graphical symbol explanation WARNING CAUTION Typical graphical symbols explanation This symbol indicates This symbol indicates This symbol indicates warnings and cautions. hazard of high voltage. mandatory actions. This symbol indicates...
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 1. Features Not only can you control and monitor the projectors via LAN connection, but also project still or wireless adapter. > LENS MEMORY The projector is capable of storing the lens shift position. > Status monitor The projector displays the present status or the error log with the sub LCD monitor.
Page 5
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Panel system Digital Mirror Device DWU851: 0.67" (17.0mm) Panel size DHD851/DWX851: 0.65" (16.5mm) Panel DWU851: 1920(H) x 1200(V) Number of pixels DHD851: 1920(H) x 1080(V) DWX851: 1280(H) x 800(V) Lamp 330W UHP x 2 HDMI Digital Signal type: T.M.D.S...
Page 6
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) (9) (10) (11) (12) Projector unit (1) Dust protector (2) Remote sensors (16) (3) Elevator feet (x2) (4) AC (AC inlet) (5) Holes for Cable Tie (6) Security slot (7) Security bar (8) Control panel...
Page 8
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 4-1 Before adjusting 4-1-1 Selection of adjustment When any parts in the table below are changed, choose the proper adjusting items with the chart. In addition, setup of the projector according to the chapter 4-5 by service engineers or users is recommended after all adjustments are done.
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 4-2 AIR SENSOR adjustment When you replaced the MAIN PCB, SENSOR-A/ Adjustment procedure B PCB or BALLAST FAN, or when you re- 1. Display the A-SENS bar with the buttons in FACTORY MENU - VID-AD1.
Page 10
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 4-4 LENS SHIFT adjustment When you replaced the ENGINE assembly Adjustment procedure 1. Display the LENS_C bar with the or MAIN PCB, make sure to carry out this buttons in FACTORY MENU - OPTION. (Example adjustment after re-assembling the projector.
Page 11
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 4-5 Setup of the projector FOCUS + / - Following contents are also described in User's manual. buttons Adjusting the zoom and focus 1. The ZOOM or FOCUS dialog will appear when you press any of the...
Page 14
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Power cannot turn on. *: Be sure to unplug the power cord before measuring resistance. voltage Measure Replace MAIN PCB. supplied at pins (5) and resistance* between (7) of E800 on the MAIN pins (5) and (7) of Replace POWER UNIT CIRCUIT1.
Page 15
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Neither lamp lights. Does Replace MAIN PCB. the Status Monitor displaying any error Replace STATUS MONTOR. message? OTHER the error message Replace ENGINE ass’y. displayed in the Status Monitor. The other of OTHER COVER: COVER ERROR is detected.
Page 16
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) LAMP ERROR is detected. LAMP UNITs are installated Re-install LAMP UNITs. correctly. Does the voltage of the pins (7) and (9) of Replace MAIN PCB. ET02 of MAIN PCB change during warming- (7) LAMP1 (9) LAMP2 Replace POWER UNIT CIRCUIT 1/2.
Page 17
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) FAN ERROR is detected. *: FAN1: LAMP 1 EXHAUST FAN FAN2: LAMP 1 UP FAN FAN3: LAMP 1 DOWN FAN FAN4: LAMP 2 EXHAUST FAN FAN5: LAMP 2 UP FAN FAN6: LAMP 2 DOWN FAN...
Page 18
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) ( DWU851/DWX851 ) Picture is not displayed correctly via COMPUTER IN ports. Turn on PbyP or PIP and select Replace IS01 : THS7327PHPR. HDMI 1 as the sub area. The picture on the main Replace MAIN PCB.
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Picture is not displayed correctly via wired/wireless* LAN. *: The USB wireless adapter is needed to use wireless LAN. communicate via wireless or total PC connection number to projector within Is total projector connection Re-connect after disconnecting other projectors.
Page 20
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Picture is not displayed correctly via VIDEO port. whether changing INPUT PCB can Replace MAIN PCB. Replace INPUT PCB. Signal from MONITOR OUT port is not displayed correctly. the projector display picture correctly via COMPUTER IN port? ( DWU851/DWX851 )
Page 21
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Focus or zoom adjustment cannnot be operated. *: Be sure to unplug the power cord before measuring resistance. any dust or distortion in the BtoB Clean the connectors with air duster. connectors on the PCBs which connect LENS and Replace the ADAPTER PCB.
Page 22
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Does the Is the Set the STANDBY MODE LED on lower right of STANDBY MODE setting as “NORMAL” in the SETUP the LAN port light in “NORMAL”? menu. green? Is the PC connected with the projector...
Page 23
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Is the USB wireless adapter connected Re-connect the USB wireless adapter properly. properly? Wait more than 1 minute after the adapter is connected. Is LED on Does MAC address PC-less Presentaion Replace MAIN PCB be read from WIRELESS...
Page 24
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Problem The projector is not turned on. Is the projector’s lamp on? No image The projector’s input source isn’t Is the LAN port selected? switched properly. sure no "ring" or "loop" connection is made occurred.
Page 25
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Troubleshooting for other Network problems (continued) Problem Can't Install Windows Vista without any Service "LiveViewer" The projector isn’t capable of relaying dynamic images such as The projected image is animation at full speed. Switching the priority to ‘Transmission ®...
Page 26
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-1 Lead free solder [CAUTION] This product uses lead free solder (unleaded) to help preserve the environment. Please read these CAUTION Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead Lead free solder indicator Printed circuit boards using lead free solder are engraved with an "F"...
Page 27
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-2 Articles necessary to your maintenance and repair works In this projector, adhesive tapes and cable ties are used for the purpose of fastening and tying the wires. Once you remove the tapes or unfasten the cable ties, you may not reuse them. We recommend you to prepare such articles, in advance.
Page 28
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-4 Installing the Batteries WARNING Always handle the batteries with care and use them only as directed. Improper use may result surrounding environment. time. Do not mix a new battery with used one. emergency treatment.
Page 29
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Filter (FIXED) slightly lift to remove it. Filter cover either from upper side or from lower side only. meshed) from the other sides to prevent from tearing apart. Filter 4, 5 (coarse meshed) replace them with new ones.
Page 30
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-6 Lamp Lamp warning WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, if the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas holes.
Page 31
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Replacing the LAMP UNIT or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.
Page 32
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-7 Other care WARNING malfunction to the projector. CAUTION Inside of the projector In order to ensure the safe use of the projector, it needs to clean and inspect the projector about once a year.
Page 33
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-8 Notice of AUTO adjustment Use of AUTO adjustment with the image through analog RGB input optimizes V_POSI, H_POSI, and H_PHASE automatically. artifacts in the image, shifts capture area and so on. Those failures are caused by period of image To avoid such phenomena, AUTO function should be used with the full size picture that has bright tone on its peripheral.
Page 34
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-9 How to inactivate the security functions This projector is equipped with security functions as below. (1) My Screen PASSWORD The My Screen PASSWORD function can be used to prohibit access to the My Screen function and prevent the currently registered My Screen image from being overwritten.
Page 35
Inquiring Code PIN BOX (ID Inquiring Code) 2. Send CHRISTIE servicing provider the Inquiring code (10 digits) to inquire the correct PIN code. 3. While the PIN BOX is displayed, enter the correct PIN Code that CHRISTIE servicing provider informed.
Page 36
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-11 Related Messages Although these messages will be automatically disappeared in about several minutes, it will be reappeared every time the power is turned on. Message Description There is no input signal. related settings. re-connect them.
Page 37
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Related Messages (continued) Message Description The button operation is not available. pressed, all button operations are not available under the following conditions. While the lens is moving, button operation from the control panel or the remote control might be ignored.
Page 38
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-12 Regarding the indicator lamps The indicators are described as below. Don't care Steady light Indicator Status Description The projector is in a standby state. The projector is warming up. Please wait. The projector is in an on state.
Page 39
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Regarding the indicator lamps (continued) Indicator Status Description Projector has detected LAMP COVER ERROR. covers. After performing any needed maintenance, turn the power on again. If the LAMP DOOR RELAY PCB and the LAMP1/2 DOOR PCB.
Page 40
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Regarding the indicator lamps (continued) Indicator Status Description Projector has detected LAMP2 WARNING. The LAMP2 UNIT is turned off. Turn the power off, and wait at least for 45 projector. Does the lamp turn off in about 1 minute after the message ”Ballast-2 NG” with It is due to wrong power unit (ballast) 2 or malfunction of power unit (ballast) 2.
Page 41
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Regarding the indicator lamps (continued) Indicator Status Description PIN LOCK function is active. Please refer to the section How to inactive the security functions and PIN LOCK System, or the chapter SECURITY menu in the User's Manual.
Page 42
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-13 HIDDEN SERVICE MENU With the control panel With the remote control 1. Press the MENU button to 1. Press the MENU button to display the ADVANCED MENU. display the ADVANCED MENU. (If EASY MENU appears, (If EASY MENU appears, choose ADVANCED MENU.)
Page 43
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) BASIC FREQ. Switches the basic vertical frequency for the output image of this projector. 50Hz 60Hz (NTSC region) SERIAL # CLEAR NETWORK RESET SOFT RESET When this is executed, all of the user data is initialized. Never use it if not required.
Page 44
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-16 Reset of the Network Web password / User ID, Network Control password ATTENTION 1. Display the WIRED SETUP in the NETWORK menu. 2. Select “OFF” in the item of DHCP. 3. Enter “255.255.255.255” in the item of IP ADDRESS.
Page 45
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-17 Status Monitor The Status Monitor is the sub LCD in the side panel that displays the Status Monitor information in the following. You can execute the following operation in the Status Monitor. Displaying the condition of the projector If no buttons are pressed, the Status Monitor displays the current status (Normal, Warning or Error) as below.
Page 46
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) In a normal state The Status Monitor displays the state of the projector in three lines. : Displays the condition of the projector. While the lamp is on, the selected port is displayed. 1st line Displayed conditions are as below;...
Page 47
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) according to the following table. Status Monitor Indicator Description current Front Front Rear Rear POWER TEMP status LAMP-1 LAMP-2 LAMP-1 LAMP-2 Lights Blinks Blinks Projector has detected LAMP COVER ERROR. COVER 1 COVER ERR In Red...
Page 48
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Lamp log Displays the usage time of the lamp1 & 2, and executes Lamp Time Reset. You can display Usage time; Displays remaining cycle time and the lamp 1 & 2 usage time. Lamp Time Reset;...
Page 49
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 6-18 Lens installation / removal procedures Caution 1. Pull out the dust protector knobs to remove it. this may lead to malfunction. to malfunction. 3. Install the lens (continued) (2) Support the lens, and move the lens lock lever to the upside (until the lens lock lever clicks into the locked position).
Page 50
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 1. Return the lens shift to the center position (1) Press the button. The LENS SHIFT dialog will appear. How to use Focus Adjustment (2) Press the button while the dialog is displayed to execute 1.
Page 51
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) DWU851/DWX851 DHD851 Option parts (Located on reverse side) Remove CW UP EXHAUST DUCT / ENGINE assembly / LAMP DOOR RELAY PCB / LAMP EXHAUST DUCT / LAMP HOUSE Continued on next page DWU851/DHD851/DWX851 Service Manual...
Page 52
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Remove METAL SHIELD DWU851/DHD851/DWX851 Service Manual 020-000755-01 Rev. 1 (11-2014)
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Notice _______________________________________________________________________ CAUTION assembling. Pay attention not to damage the wires or any other fragile parts of the projector. Be sure to lock the connectors which has locking mechanism. (Push in until it clicks.) Be sure to lock the claw of ferrite cores and careful not to pinch the wires.
Page 54
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Assembling 1. Make sure the direction, and put the LAMP EXHAUST FAN on the LAMP DOOR. Make the labeled side face LAMP DOOR (outside), and pull out the fan cable from the side near the other lamp cover assembly.
Page 55
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) UPPER CASE (UPPER CASE, FRONT COVER) NOTE: Remove the LENS unit before disasembling the UPPER CASE. Refer to the section Lens installation / removal procedures of the chapter Service points about assembling/disassembling LENS unit (and front cover).
Page 56
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) As replacement of UPPER CASE Put the rib on the UPPER Remember to detach the shading sheets and re-use CASE into the slot of the them with new UPPER CASE. The service parts do not include the sheets.
Page 57
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) MAIN PCB block (MAIN / INPUT / KEYPAD / SUB LCD PCB, STATUS MONITOR, CONTROL BUTTON, I/O COVER, USB MINI COVER) Disassembling Assembling 1. Disconnect all the cables from the MAIN 1. Check the wiring if it is properly prepared.
Page 58
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Wiring Check the wiring around the MAIN PCB block before attaching the MAIN PCB block for preparing. <Side of power unit circuit case> Lead CNPW2 upward. Power unit circuit case Pass CNPW1 and CNTS between the power unit circuit case and 2 bosses, and hook on the cover.
Page 59
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) After attaching the MAIN PCB block Connect and wire all the cables to be connected to the MAIN PCB as below. The cables with pale blue frame and pointing arrow are from ENGINE assembly. Refer to each section for the detail of wiring procedure.
Page 60
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Rear side of the MAIN PCB Wire the cables in the area surrounded with yellow dotted line according to following procedure. 1. Connect and style Connect CNPW1. Connect CNPW2. CNPW1 and CNPW2. Style CNPW1 as shown Add CNPW2 to the hook as shown.
Page 61
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) ENGINE (left) side of the MAIN PCB Wire the cables in the area surrounded with orange dotted line according to following procedure. CNDCR, CNLAD, CNSTR and IRIS UNIT cable. CNLAD, CNSTR, IRIS UNIT cable and CNDCR.
Page 62
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Bundle temperature sensor cable and CNCWC with the ferrite core, and connect them. Connect CNHS. LAMP2 UP FAN cable Connect temperature sensor cable. Connect CNCWC. Bundle LAMP2 UP FAN cable, temperature sensor cable and CNCWC with the ferrite core. Fasten the core with a cable tie.
Page 63
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) I/O COVER, USB MINI COVER ( DWU851/DWX851 ) Disassembling M3x8, black screw, torque: 0.39~0.59N·m 1) Remove a screw to detach USB MINI COVER. 2) Remove a screw and release 4 hooks on the I/O COVER from the I/O METAL.
Page 64
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) I/O COVER, USB MINI COVER ( DHD851 ) Disassembling M3x8, black screw, torque: 0.39~0.59N·m 1) Remove 2 screws to detach USB MINI COVER. 2) Remove a screw and release 4 hooks on the I/O COVER from the I/O METAL.
Page 65
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Assembling < > Put the INPUT PCB together with the I/O METAL, and fasten 6 screws as before. < > screws and USB MINI COVER as before. HDMI2 port. l l a ( DWU851/DWX851 ) ( DHD851 ) Shading sheet...
Page 66
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Connect and wire 4 harnesses, CNPC2, CNUAR, CNVID and CNUSB. NOTE: Connect CNPC2 and CNUAR to MAIN PCB with bound side. ( DWU851/DWX851 ) Connect CNPC2 and CNUAR. Connect CNVID. INPUT PCB Connect CNUSB. Style CNUSB as shown.
Page 67
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) STATUS MONITOR, SUB LCD / KEYPAD PCB, CONTROL BUTTON LCD cushion Disassembling STATUS MONITOR Hook cable. 2) Release the STATUS MONITOR from 2 hooks on the CONTROL BUTTON frame. 3) Tear off the tape and disconnect the harness from the back side of the SUB LCD PCB.
Page 68
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) LAMP EXHAUST DUCT (LAMP DOOR RELAY PCB) Disassembling 1. Disconnect all the harnesses from the LAMP DOOR RELAY PCB. 2. Remove a screw from the power unit LAMP EXHAUST DUCT Power unit circuit case circuit case which secures the earth cable CNGD2.
Page 69
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) LAMP HOUSE (LAMP1/2 SW. PCB, Thermal sw. TSW1/2) NOTE: Remove the LAMP EXHAUST DUCT before disassembling the LAMP HOUSEs. Disassembling 1. Remove 3 screws to detach the LAMP DUCT UP SASSY. LAMP DUCT 2. Pull out the thermal sw.
Page 70
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Wiring Pass the LAMP2 DOWN FAN cable Before attaching the LAMP HOUSEs and CNCS1 through the clamp. Wire CNCS1 before attaching the LAMP1 HOUSE. Check the arrangement of CNCS2 as shown below before connecting it. Be sure to connect CNCS2 to LAMP2 SW.
Page 71
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) POWER UNIT HOLDER T3x12, black screw, NOTE: torque: 0.68~0.88N·m Remove the MAIN PCB block before disassembling the POWER UNIT HOLDER. AC holder Disassembling Remove 2 screws, and pull the POWER UNIT HOLDER up. Assembling Put the POWER UNIT HOLDER on the POWER EXHAUST...
Page 72
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) NOTE: CW UP EXHAUST DUCT, MAIN PCB block, LAMP EXHAUST DUCT, LAMP HOUSEs and POWER UNIT HOLDER before detaching the ENGINE assembly. the ass'y unit even when it stays on the BOTTOM CASE, but it is necessary to detach the ass'y unit before replacing the SHUTTER UNIT.
Page 73
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Wiring Before attaching the ENGINE assembly Check the wiring around the ENGINE assembly before attaching the ass'y unit for preparing. DC RELAY PCB Pass the IRIS the duct side of the boss. Fasten CNBL2 on the left side...
Page 74
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Connect CNLAD. NOTE: It is not necessary to detach ENGINE assembly before detaching the ADAPTER PCB. Disassembling Disconnect the cable CNLAD, and remove 2 screws to detach ADAPTER PCB. Assembling Connect CNLAD to the ADAPTER PCB, and screw down the PCB as before.
Page 75
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) SHUTTER UNIT NOTE: DWU851/DHD851/DWX851 Service Manual 020-000755-01 Rev. 1 (11-2014)
Page 76
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) BALLAST UNIT (BALLAST FAN, POWER UNIT1/2 BALLAST, SENSOR-A/B PCB, DC RELAY PCB) Disassembling 1) Disconnect all the remained cables on the DC RELAY PCB, remove 2 screws to detach the PCB. 2) Remove 2 screws to detach the ballast shield.
Page 77
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Ballast cover (BALLAST FAN) Disassembling 1) Remove 4 screws to detach the ballast cover. Put away CNBL2 and BALLAST FAN cable from the holes on the ballast cover carefully. 2) Remove the BALLAST FAN. Ballast cover...
Page 78
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Ballast holder Slide the holder Disassembling 1) Remove 4 screws and slightly CNPF1 lift and slide the ballast holder. 2) Remove 2 screws to detach the ballast cable shield. 3) Disconnect CNPF1 on the T3x12...
Page 79
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) POWER UNIT2 BALLAST Partition Disassembling 1) Disconnect CNLP2 and CNBL2 from the POWER UNIT2 BALLAST. 2) Remove a screw to detach the POWER UNIT2 POWER UNIT2 BALLAST from the ballast holder. BALLAST 3) Detach the insulating covers from POWER UNIT2 BALLAST.
Page 80
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) POWER UNIT1 BALLAST Insulating sheet Disassembling Ballast holder 1) Turn over the ballast holder, disconnect CNLP1 and CNBL1 from POWER UNIT1 BALLAST and put the cables away from the holes. POWER 2) Remove 2 screws to detach POWER UNIT1 BALLAST UNIT1 and the insulating sheet from the holder.
Page 81
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) SENSOR-A/B PCB Ballast cover Disassembling 1) Disconnect CNOSS and CNISS from SENSOR-A PCB and SENSOR-B PCB. 2) Turn the cover over, and remove the sensor cover. SENSOR-B PCB 3) Remove SENSOR-A PCB and SENSOR-B PCB from the cover.
Page 82
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Wiring Sensor Wire CNOSS and CNISS through the holes on cover ballast cover as below. SENSOR-A SENSOR-B Ballast Cover ATTENTION Make sure that the insulating sheet is not floating from the Ballast cover. If it is floating, stick it to the Ballast cover.
Page 83
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) REAR POWER UNIT (POWER UNIT1/2 CIRCUIT, POWER EXHAUST FAN) NOTE: Remove the MAIN PCB block before disassembling the POWER UNIT HOLDER. Disassembling 1) Remove a silver screw to detach CNGDS. 2) Remove 4 silver and 2 black screws to detach the circuit holder.
Page 84
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) 4) Wire the cables and attach the partition as below. CNAC1 CNPF1 CNTS CNPW1 POWER UNIT1 CIRCUIT Wire CNPF1 beneath POWER UNIT1 CIRCUIT. Wire CNAWV beneath POWER UNIT1 CIRCUIT. Partition Clip the partition POWER UNIT1...
Page 85
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) POWER UNIT2 CIRCUIT T3x12 Insulating Disassembling black screws 1) Remove 2 screws to detach the insulating lid. 2) Remove 3 screws, put the cables away from the holes Torque: 0.68- and detach POWER UNIT2 CIRCUIT from the circuit 0.88Nm...
Page 86
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) (AC WATCH PCB, POWER UNIT COOLING, POWER INTAKE FAN, BATTERY PCB) Remove the MAIN PCB block before disassembling the REAR POWER UNIT. Disassembling 1) Remove 2 silver and 3 black screws, detach the AC holder and disconnect CNAWV from the AC WATCH PCB.
Page 87
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Assembling Confirm there is no excess length of harnesses of CNPW1 and 1) Attach the BATTERY PCB and the battery CNTS in the power unit case. holder in place on the bottom case and screw down.
Page 88
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) NOTE: Wire CNAC1 and CNAC2 before installing AC RELAY /Peltier Power UNIT to the bottom case as shown below. Twist CNAC1 and CNAC2 one or one and a half times in clockwise after locking to the clamp, and wire it here.
Page 89
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) Wiring Wire the cables as below. ATTENTION Loop CNACR as below. Wire CNACR by passing it through this groove. CNACR Outside View Side View AC holder CNACR & CNAC CNAWD Wire CNAC through this hook.
Page 90
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) AC WATCH PCB T3x12 black screws Disassembling 1) Disconnect all the cables on the AC WATCH PCB. AC WATCH 2) Remove 2 screws to detach the AC WATCH PCB. 3) Separate the AC shield and the AC holder.
Page 91
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) LAMP1/2 DOWN FAN, IRIS FAN Disassembling 1) Remove 3 screws to detach the lamp duct. 2) Remove 2 screws each to detach the LAMP1/2 DOWN FAN and IRIS FAN. 3) Remove a screw to detach the metal mesh and the insulating sheet.
Page 92
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) IRIS FAN 40mm IRIS FAN Pass IRIS FAN cable through this groove. BOTTOM CASE Insulating sheets Disassembling Remove 19 screws and detach the insulating sheets and the bottom metal. Bottom metal NOTE Remember to detach the insulating sheets and the bottom metal and re-use them with new BOTTOM CASE.
Page 93
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. [DWU851(121-029102-01): White model] SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS’Y DD1B...
Page 94
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. [DHD851(121-030104-01): White model] SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS’Y DD1B...
Page 95
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. [DWX851(121-031105-01): White model] SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS’Y DD1B...
Page 96
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS'Y DD1B 31 JP78606...
Page 97
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS’Y DD1B 31 JP78606...
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS'Y DD1B 31 JP78606...
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS'Y DD1B 31 JP78606...
Page 100
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS’Y DD1B 31 JP78606...
Page 101
DWU851(DD1-WU70P/71P) / DHD851(DD1-HD70P/71P) / DWX851(DD1-WX70P/71P) PRODUCT SAFETY NOTE: have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. SYMBOL SYMBOL PARTS No. DESCRIPTION PARTS No. DESCRIPTION 1 DT01725 LAMP UNIT ASS'Y DD1B 31 JP78606...