Related Manuals for Vecow RCX-1500 PEG
Summary of Contents for Vecow RCX-1500 PEG
- Page 1 USER USER RCX-1500 PEG Manual Manual Intel ® Xeon ® /Core ™ i7/i5/i3 Dual GPU AI Computing System Workstation-grade, NVIDIA ® Tesla ® /Quadro ® /GeForce ® Graphics 2.2.0 Edition 20191213...
- Page 2 2019/07/01 All Official Release 2.00 2019/07/24 iv, v, 1, 2, 3, 5, 7 Update 2.10 2019/10/05 Cover, iv, 1, 2, 3, 5, 7, 9, Update 44, 45, 49, 98, 99, 2.20 2019/12/13 3, 5, 55 Update ©Vecow RCX-1500 PEG User Manual...
-
Page 3: Declaration Of Conformity
This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of Vecow Co., Ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of the product or documentation or any infringements upon the rights of third parties, which may result from such use. - Page 4 6 USB 3.1, 2 SIM, 32 Isolated DIO CPU List Series Cores GHz Cores GHz E-2278GE E-2176G ® Intel E-2278GEL ® Xeon E-2124G E-2226GE i7-8700 i7-9700E i7-8700T i7-9700TE i5-8500 i5-9500E ® Intel ™ Core i5-8500T i5-9500TE i3-8100 i3-9100E i3-8100T i3-9100TE ©Vecow RCX-1500 PEG User Manual...
-
Page 5: Optional Accessories
Terminal Block 20-pin to Terminal Block 20-pin Cable, 500cm Terminal Board with One 20-pin Terminal Block Connector and TMB-TMBK-20P DIN-Rail Mounting 4G Module Mini PCIe 4G/GPS Module with Antenna WiFi & Bluetooth WiFi & Bluetooth Module with Antenna ©Vecow RCX-1500 PEG User Manual... -
Page 6: Table Of Contents
1.4 Supported CPU List 1.5 Mechanical Dimension 1.5.1 Dimensions of RCX-1500R PEG 1.5.2 Dimensions of RCX-1500 PEG CHAPTER 2 GETTING TO KNOW YOUR RCX-1500 PEG 9 2.1 Packing List 2.2 Front Panel I/O Functions 2.3 Main Board Expansion Connectors 2.4 Main Board Jumper Settings 2.5 Ignition Control... - Page 7 3.7 Installing Sim Card 3.8 Installing PCI/PCIe Card 3.9 Installing SSD/HHD 3.10 Mounting Your RCX-1500 PEG 3.11 Installing Hold-down Kit CHAPTER 4 BIOS AND DRIVER 4.1 Entering BIOS Setup 4.2 Main 4.3 Advanced 4.4 Chipset 4.5 Security 4.6 Boot 4.7 Save & Exit...
-
Page 8: Chapter 1 General Introduction
EN50155 and EN50121-3-2 compliant, Vecow RCX-1500 PEG Series Dual GPU AI Computing System serves extreme performance, system-optimized operation, versatile configurations, smart manageability and trusted reliability for your AIoT/ Industry 4.0 applications. -
Page 9: Features
• System-oriented power optimization, up to dual 350W independent graphics card • 6V to 36V DC Power Input with 80V Surge Protection • 12V Power Input for dual independent graphics card • Configurable Ignition Power Control ©Vecow RCX-1500 PEG User Manual GENERAL INTRODUCTION... -
Page 10: Product Specification
4 SATA III (6Gbps) support software RAID 0, 1, 5, 10 mSATA 2 SATA III (Mini PCIe Type, 6Gbps) • 4 Front-access 2.5" SSD/HDD Tray Storage Device • 1 M.2 Key M Socket ©Vecow RCX-1500 PEG User Manual GENERAL INTRODUCTION... - Page 11 5% to 95% humidity, non-condensing Relative Humidity 95% at 45°C • IEC 61373 : 2010 Shock & Vibration • Railway Applications : Rolling Stock Equipment, Shock and Vibration Test CE, FCC, EN50155, EN50121-3-2 ©Vecow RCX-1500 PEG User Manual GENERAL INTRODUCTION...
-
Page 12: Specifications Of Rcx-1500 Peg
1.3.2 Specifications of RCX-1500 PEG System ® ® 8 cores Intel Xeon /Core™ i7/i5/i3 Processor Processor (Coffee Lake Refresh) ® Chipset Intel C246 Chipset BIOS IT8786E • DDR4 2666MHz (ECC/Non-ECC) Memory • Up to 128GB • 4 260-pin SO-DIMM Socket... - Page 13 5% to 95% humidity, non-condensing Relative Humidity 95% at 45°C • IEC 61373 : 2010 Shock & Vibration • Railway Applications : Rolling Stock Equipment, Shock and Vibration Test CE, FCC, EN50155, EN50121-3-2 ©Vecow RCX-1500 PEG User Manual GENERAL INTRODUCTION...
-
Page 14: Supported Cpu List
1.4 Supported CPU List Series Cores GHz Cores GHz E-2278GE E-2176G ® Intel E-2278GEL ® Xeon E-2124G E-2226GE i7-8700 i7-9700E i7-8700T i7-9700TE i5-8500 i5-9500E ® Intel ™ Core i5-8500T i5-9500TE i3-8100 i3-9100E i3-8100T i3-9100TE ©Vecow RCX-1500 PEG User Manual GENERAL INTRODUCTION... -
Page 15: Mechanical Dimension
1.5 Mechanical Dimension 1.5.1 Dimensions of RCX-1500R PEG Unit : mm (inch) 210.0 (8.27”) 160.0 (6.30”) 1.5.2 Dimensions of RCX-1500 PEG Unit : mm (inch) 210.0 (8.27”) 160.0 (6.30”) ©Vecow RCX-1500 PEG User Manual GENERAL INTRODUCTION... -
Page 16: Chapter 2 Getting To Know Your Rcx-1500 Peg
Item Description RCX-1500 PEG AI Computing System (According to the configuration you order, the RCX-1500 PEG series may contain SSD/HDD and DDR4 SO-DIMM. Please verify these items if necessary.) RCX-1500R PEG Series Accessory box, which contains • Vecow Drivers & Utilities DVD •... -
Page 17: Front Panel I/O Functions
2.2 Front Panel I/O Functions In Vecow’s RCX-1500 PEG series family, all I/O connectors are located on the front panel. Most of the general connections to the computer device, such as audio, USB, DVI-I, COM Port, Isolated DIO, Display Port, and any additional storage, are placed on the front panel. -
Page 18: Power Button
S3, S5 Suspend to RAM, System off with standby power To power on RCX-1500 PEG, press the power button which will light the blue LED. To power off RCX-1500 PEG, you can either command shutdown by OS operation or simply press the power button. If system error appears, press and hold the power button for four seconds to shut down the machine directly. - Page 19 The VGA output mode supports up to 1920x1200 resolution. If use VGA function will need a DVII to VGA module connecting to DVI-I device. Right is the DVII to VGA module picture ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 20 There are 6 USB 3.1 connections available supporting up to 10GB per second data rate in the front side of Vecow RCX-1500 PEG series. It also compliant with the requirements of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).
- Page 21 PEG Power COM 1 There are two 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections on the front side of Vecow RCX-1500 PEG. LAN 1 is powered by ® Intel I219LM Ethernet engine, and LAN 2 is powered by Intel I210 Ethernet engine.
-
Page 22: Audio Connector
To utilize the audio function on the Windows platform, you need to install ® corresponding drivers for both Intel C246 chipset and Realtek ALC892 codec. Please refer to chapter four for more details on driver installation. ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG... - Page 23 | LAN 1 | LAN 2 Digital Display On | Off DVI-I PEG Power COM 1 RCX-1500 PEG supports 6V to 36V DC power input. Pin No. Definition Earth GND ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 24 • 3-KVRMS Isolation for 1 minute per UL 1577 • CSA Component Acceptance Notice 5A, IEC 60950-1 and IEC 61010-1 End Equipment Standards PIN 1 ~ 8 PIN 11 ~ 18 • GB4943.1-2011 CQC Certified ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 25 SIO_GPO0 OUTPUT 9 SIO_GPO1 OUTPUT 10 SIO_GPO2 OUTPUT 11 SIO_GPO3 OUTPUT 12 SIO_GPO4 OUTPUT 13 SIO_GPO5 OUTPUT 14 SIO_GPO6 OUTPUT 15 SIO_GPO7 GND_ISO_DIO2 External 6-40VDC (NPN) External 6-48VDC (PNP) ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 26 DO Signal circuit in SINK mode (NPN) Source (PNP) DIO_VDC (20) LOAD 7.2K ISOLATION 6-40V (11) (300mA) 1.5K GNDI GNDO GNDO (10.19) Internal Circuit External Device GNDO DO Signal circuit in source mode (PNp) ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 27 (3-wire) TXD- TXD- DATA- TXD+ TXD+ DATA+ RXD+ RXD+ ----------- RXD- RXD- ----------- 1, 2 3, 4 ----------- RTS- ----------- ----------- RTS+ ----------- ----------- CTS+ ----------- ----------- CTS- ----------- ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 28 DIO 1 Isolated DIO 2 SIM 2 SIM 1 DC-IN | LAN 1 | LAN 2 Digital Display On | Off DVI-I PEG Power COM 1 PEG Power 12V(Only) ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
-
Page 29: Main Board Expansion Connectors
2.3 Main Board Expansion Connectors 2.3.1 Front View of RCX-1500 PEG Main Board With Connector Location SODIMM 2 SODIMM 1 CN10 JCOM2 SATA4 SATA3 JCOM1 SODIMM 4 SODIMM 3 JBAT1 SATA1 SATA2 JUSB1 JDEBUG1 BIOS HDD_PWR1 HDD_PWR2 SYS_FAN2 SYS_FAN1 Super I/O... - Page 30 2.3.2 Rear View of RCX-1500 PEG Main Board With Connector Location CN17 ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 31 Fan PWM 2.3.4 JBAT1 : Battery The RCX-1500 PEG’s real-time clock is powered by a lithium battery. It is equipped with Panasonic BR2032 190mAh lithium battery. It is recommended that you do not replace the lithium battery on your own. If the battery needs to be changed, please contact the Vecow RMA service team.
- Page 32 Reserved +V3.3S +V3.3A PLTRST_PCIE# WAKE# Reserved CLKOUT_100M_X4_P0 CLKOUT_100M_X4_N0 PCIE_TXP21 PCIE_TXN21 PCIE_RXP21 PCIE_RXN21 Reserved Reserved PCIE_TXP22 PCIE_TXN22 PCIE_RXP22 PCIE_RXN22 PCIE_TXP23 PCIE_TXN23 PCIE_RXP23 PCIE_RXN23 PCIE_TXP24 PCIE_TXN24 PCIE_RXP24 PCIE_RXN24 CLKOUT_100M_X4_P1 CLKOUT_100M_X4_N1 Reserved ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 33 Pin No. Definition Reserved +V12S +V12S +V12S +V12S +V12S CLKOUT_100M_X16_P2 SM_SLOT_CLK CLKOUT_100M_X16_N2 SM_SLOT_DAT USB_P8_DP USB_P8_DN +V3.3S +V3.3S +V3.3S +V3.3A PLTRST_PCIE# WAKE# Reserved CLKOUT_100M_X16_P0 CLKOUT_100M_X16_N0 PEG_TXP_0 PEG_TXN_0 PEG_RXP_0 PEG_RXN_0 Reserved ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 34 PEG_RXN_2 PEG_TXP_3 PEG_TXN_3 PEG_RXP_3 PEG_RXN_3 PCIE_RXP7 PCIE_RXN7 CLKOUT_100M_X16_P1 CLKOUT_100M_X16_N1 PEG_TXP_4 PEG_TXN_4 PEG_RXP_4 PEG_RXN_4 PEG_TXP_5 PEG_TXN_5 PEG_RXP_5 PEG_RXN_5 PEG_TXP_6 PEG_TXN_6 PEG_RXP_6 PEG_RXN_6 PEG_TXP_7 PEG_TXN_7 PEG_RXP_7 PEG_RXN_7 Reserved Reserved PEG_TXP_8 PEG_TXN_8 ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 35 PEG_TXN_9 PEG_RXP_9 PEG_RXN_9 PEG_TXP_10 PEG_TXN_10 PEG_RXP_10 PEG_RXN_10 PEG_TXP_11 PEG_TXN_11 PEG_RXP_11 PEG_RXN_11 PEG_TXP_12 PEG_TXN_12 PEG_RXP_12 PEG_RXN_12 PEG_TXP_13 PEG_TXN_13 PEG_RXP_13 PEG_RXN_13 PEG_TXP_14 PEG_TXN_14 PEG_RXP_14 PEG_RXN_14 PEG_TXP_15 PEG_TXN_15 PEG_RXP_15 PEG_RXN_15 PCIE_TXP7 PCIE_TXN7 ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 36 1500 PEG. It supports higher storage capacity with less cabling effort and smaller required space. The pin assignments of SATA1, SATA2, SATA3, and SATA4 are listed in the following table : Pin No. Definition Pin No. Definition ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 37 HDD_PWR1 HDD_PWR2 The RCX-1500 PEG is also equipped with two SATA power connectors. It supports 5V (Up to 3A) and 12V (Up to 3A) currents to the hard drive or SSD. The pin assignments of HDD_PWR1 and HDD_PWR2 are listed in the following table : Pin No.
- Page 38 2.3.11 JUSB1 : Internal Dual Port USB 2.0 JUSB1 The RCX-1500 PEG main board provides up to two expansion USB ports using plug-and-play for Dongle Key or LCD touch panel. The USB interface supports 480Mbps transfer rate which complies with high speed USB specification Rev.
- Page 39 0. The pin assignments of MPCIE1, MPCIE2 are listed in the following table : Pin No. Definition Pin No. Definition Reserved +3.3Vaux Reserved Reserved +1.5V Reserved Reserved Status Reserved ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 40 USB_D+ USB_D- PETp0 PETn0 SMB_DATA SMB_CLK +1.5V PERp0 PERn0 +3.3Vaux PERST# Reserved reserved Reserved Mechanical Key Reserved REFCLK+ Reserved REFCLK- Reserved Reserved CLKREQ# Reserved Reserved 1.5V Reserved WAKE# 3.3Vaux ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 41 RCX-1000 24V to 36V DC power input, CN6 support 12V output. The pin assignments of CN6 are listed in the following table : Pin No. Definition Pin No. Definition +V12_ATX +V12_ATX +V12_ATX +V12_ATX 2.3.14 J2 : Miscellaneous Pin Header ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 42 Group Pin No. Definition HDD_LED_P HDD LED HDD_LED_N FP_RST_BTN_N RESET BUTTON Ground PWR_LED_P POWER LED PWR_LED_N FP_PWR_BTN_IN POWER BUTTON Ground 2.3.15 SODIMM1, SODIMM2, SODIMM3, SODIMM4 SODIMM2 SODIMM1 SODIMM4 SODIMM3 ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 43 SODIMM_2 SODIMM_2 SODIMM_4 SODIMM_2 SODIMM_1 SODIMM_2 SODIMM_1 SODIMM_4 SODIMM_4 SODIMM_3 SODIMM Quantity Location SODIMM_2 SODIMM_2, SODIMM_4 SODIMM_2, SODIMM_4, SODIMM_1 SODIMM_2, SODIMM_4, SODIMM_1, SODIMM_3 ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 44 ALERT# (O)(0/3.3V) 12C_CLK (I)(0/3.3V) RESERVED/PERn1 12C_DATA (I/O)(0/3.3V) RESERVED/PERp1 PEWAKE0# (I/O) (0/3.3V) PERST0# (I)(0/3.3V) CLKREQ0# (I/O) (0/3.3V) REFCLKn0 REFCLKp0 PETn0 PETp0 PERn0 PERp0 Module Key Module Key Module Key Module Key ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 45 PCIe or SATA, or Solid State Storage Devices (SSD). The size of module is limited to 2280. Pin Out : Pin No. Definition Pin No. Definition 3.3V 3.3V 3.3V SCUSCLK (3.2KHz)(O) PEDET (NC-PCIe/GND- (0/3.3V) SATA) Connector Key ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 46 N/C PETp0/SATA-A+ PETn0/SATA-A- PERp0/SATA-B- PERp0/SATA-B+ DEVSLP (O) PETp1 PETn1 PERp1 PERn1 PETp2 PETn2 3.3V PERp2 3.3V PERn2 3.3V 3.3V PETp3 DAS/DDS# (I/O)/LED1# (I) PETn3 (0/3.3V) PERp3 3.3V PERn3 3.3V ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 47 DIO2_GPI0 SIO_GPI81 DIO2_GPI1 SIO_GPI82 DIO2_GPI2 SIO_GPI83 DIO2_GPI3 SIO_GPI84 DIO2_GPI4 SIO_GPI85 DIO2_GPI5 SIO_GPI86 DIO2_GPI6 SIO_GPI87 DIO2_GPI7 SIO_GPO70 DIO2_GPO0 SIO_GPO71 DIO2_GPO1 SIO_GPO72 DIO2_GPO2 SIO_GPO73 DIO2_GPO3 SIO_GPO74 DIO2_GPO4 SIO_GPO75 DIO2_GPO5 SIO_GPO76 DIO2_GPO6 ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
- Page 48 UART4_MODE1 UART3_MODE2 UART4_MODE2 SP338E_TERM_COM3 SP338E_TERM_COM4 +V3.3S +V3.3S +V3.3S +V3.3S SIO_GP60 SIO_GP47 SIO_GP61 SIO_GP62 USB3_PCH_RXN1 USB3_PCH_RXN2 USB3_PCH_RXP1 USB3_PCH_RXP2 USB3_PCH_TXN1 USB3_PCH_TXN2 USB3_PCH_TXP1 USB3_PCH_TXP2 USB_P1_DP USB_P2_DP USB_P1_DN USB_P2_DN +V5A +V5A +V5A +V5A ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
-
Page 49: Main Board Jumper Settings
You may configure your card to match the needs of your application by DIP switch. As below show the deep switch on and off. 1 : OFF 1 : ON 1 : ON 2 : OFF 2 : OFF 2 : ON ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG... - Page 50 JCFG1 CPU PCIe x 16 (CN9) configuration table as follows : PCIe Configuration Header 1 x8, 2 x4 (3-5) (4-6) 2 x 8 (3-5) (2-4) 1 x16 (1-3) (2-4) ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
-
Page 51: Clear Cmos
Digital Display On | Off DVI-I PEG Power COM 1 Pin No. Definition USB 3.0 and USB 2.0 Wake Up Enable (Default) USB 3.0 and USB 2.0 Wake Up Disable ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG... - Page 52 2.4.6 FAN2 Header FAN2 Pin No. Definition SYS_FAN2 : PCH PWM Control (Default) SYS_FAN2 : Full Speed ©Vecow RCX-1500 PEG User Manual GETTING TO KNOW YOUR RCX-1500 PEG...
-
Page 53: Ignition Control
2.5 Ignition Control 2.5.1 SW1 : Ignition Control The RCX-1500 PEG series provide ignition power control feature for in-vehicle applications. The built-in MCU monitors the ignition signal and turns on/off the system according to pre-defined on/off delay period. ©Vecow RCX-1500 PEG User Manual... - Page 54 2.5.2 Adjust Ignition Control Modes The RCX-1500 PEG series provide sixteen modes of different power on/off delay periods adjustable via rotary switch. The default rotary switch is set to 0 in ATX/AT power mode. The modes are listed in the following table :...
- Page 55 Note : 1. DC power source and IGN share the same ground. 2. RCX-1500 PEG supports 6V to 36V wide range DC power input in ATX/AT mode. In Ignition mode, the input voltage is fixed to 12V/24V for car battery scenario.
-
Page 56: Chapter 3 System Setup
SYSTEM SETUP 3.1 How to open your RCX-1500 PEG Remove F-Head 6#-32 screws (marked in red) on the top cover (11 places). ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 57: Installing Cpu
3.2 Installing CPU Step 1 Remove PH M3x6L screws (10 places) ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 58: Installing Ddr4 So-Dimm Modules
Step 1 Install DDR4 RAM module Step 2 Make sure the RAM module into SO-DIMM slot. is locked by the memory slots (red). For information of DIMM installation sequence, please refer to section 2.3.15. ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 59: Installing Mini Pcie Card
Step 1 Install Mini PCIe card into Step 2 Fasten one M2.5 screws. the Mini PCIe slot. 3.5 Installing M.2 (Key E/Key M) Step 1 Install M.2 card into the Mini PCIe slot. Step 2 Fasten one M3 screws. ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 60: Installing Antenna Cable
3.6 Installing Antenna Cable Step 1 Remove one halt shear hole from the rear panel (pick up the location you want). ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 61: Installing Sim Card
Step 3 Fasten washer 1, washer 2, and on Antenna cable connector 3.7 Installing Sim Card Step 1 Remove SIM cover Step 2 Install SIM card in the (Remove 6#-32 x 5L screws). marked yellow area. ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 62: Installing Pci/Pcie Card
3.8 Installing PCI/PCIe Card Supports the full length 312mm (without card bracket), 124.5mm height and 2.5-Slot card widthof PCI/PCIe expansion card. Step 1 Remove the M3x5L screw and the bracket. ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... - Page 63 Step 2 Install the PCI/PCIe Card and lock it in place. Step 3 Tighten one M3x5L screws. Notice : please press the clip before removing the card. ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP...
-
Page 64: Installing Ssd/Hhd
3.9.1 External SSD/HDD for RCX-1500FR PEG Step 1 Unlock SSD/HDD Tray. Step 2 Install 2.5'' SSD/HDD into the tray. Step 3 Close the SSD/HDD tray. Step 4 Lock the SSD/HDD tray with the key. unlock lock ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... - Page 65 3.9.2 Internal SSD/HDD for RCX-1500 PEG Step 1 Remove 6#-32 x 5L screws. Step 2 Unlock the HDD tray and install 2.5'' SSD/HDD into the tray. Step 3 Tighten four F Head M3x4L screws (1 set). ©Vecow RCX-1500 PEG User Manual...
-
Page 66: Mounting Your Rcx-1500 Peg
3.10 Mounting Your RCX-1500 PEG Step 1 Install wall mount to RCX-1500 bottom. Step 2 Install four F head #6-32x6L screws. ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 67: Installing Hold-Down Kit
Step 3 Fix the screws (marked in red) left or right with Phillips screwdriver to adjust the height of the hold on bar. down ©Vecow RCX-1500 PEG User Manual SYSTEM SETUP... -
Page 68: Chapter 4 Bios And Driver
Figure 4-1 : Entering Setup Screen BIOS provides an interface for users to check and change system configuration. The BIOS setup program is accessed by pressing the <Del> key when POST display output is shown. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... -
Page 69: Main
Set the time. Use <Tab> to switch between time elements. 4.3 Advanced Figure 4-3 : BIOS Advanced Menu Select advanced tab to enter advanced BIOS setup options, such as CPU configuration, SATA configuration, and USB configuration. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... - Page 70 Enable/disable CPU Advanced Encryption Standard instructions. Intel Trusted Execution Technology ® Enables utilization of additional hardware capabilities provided by Intel Trusted Execution Technology. Changes require a full power cycle to take effect. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 71 CPPCv2 interface to allow for hardware controlled P-states. Turbo Mode Turbo Mode. C states Enable or disable CPU C states. Enhanced C-states Enable/disable C1E. When enabled, CPU will switch to minimum speed when all cores enter C-State. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 72 MEBx Setup. AMT Configuration ® Configure Intel Active Management Technology Parameters. ME Unconfig on RTC Clear State Disabling this option will cause ME not to unconfigure on RTC clear. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
-
Page 73: Trusted Computing
4.3.6 SMART Settings Figure 4-3-6 : SMART Settings SMART Self Test Run SMART self test on all HDDs during POST. 4.3.7 IT8786 Super IO Configuration Figure 4-3-7 : IT8786 Super IO Settings ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... -
Page 74: Hardware Monitor
Temperature Limit value of Fan Start (Degree C). (Range : 10~80) PWM Start Value (%) Default PWM Value of Fan. (Range : 15%~100%) Full Speed Temperature Temperature Limit value of Fan Full Speed (Degree C). (Range : 50~90) ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... - Page 75 Legacy Console Redirection Settings. Serial Port for Out-of-Band Management/Windows Emer ency Management Services (EMS) Console redirection enable or disable. 4.3.10 Intel TXT Information Figure 4-3-10 : Intel TXT Information Display Intel TXT information. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 76 Globally Enables or Disables Hot-Plug support for the entire System. If system has Hot-Plug Capable Slots and this option set to Enabled, it provides a Setup screen for selecting PCI resource padding for Hot-Plug. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 77 IP6 Configuration Policy Set IP6 Configuration Policy. PXE boot wait time Wait time to press ESC key to abort the PXE boot. Media detect count Number of times presence of media will be checked. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 78 Controls the execution of UEFI and Legacy Storage OpROM. Video Allows more than two frequency ranges to be supported. Other PCI devices Determines OpROM execution policy for devices other than network, storage, or video. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 79 Maximum time the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value, for a root port it is 100 ms, for a hub port the delay is taken from the hub descriptor. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
-
Page 80: Chipset
Above 4GB MMIO BIOS assignment Enable/disable above 4GB MemoryMappedIO BIOS assignment. This is disabled automatically when aperture size is set to 2048MB. 4.4.1.1 Memory Configuration Figure 4-4-1-1 : Memory Information Displays memory information. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... - Page 81 DVMT Pre-Allocated Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 82 Specify what state to go to when power is re-applied after a power failure (G3 state). S0 State : Always turn-on the system when power source plugged-in. S5 State : Always turn-off the system when power source plugged-in. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 83 Enable/Disable the control of Active State Power Management on SA side of the DMI Link. Native PCIE Enable PCIE Express Native Support Enable/Disable. PCI Express device settings Bios options for PCI Express device setting. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
- Page 84 On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device. SATA Device Type Identifies that the SATA port is connected to solid state drive or hard disk drive. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
-
Page 85: Security Configuration
System Fan 2 speed control (High/Mid/Low). HDMI 4K Support (Digital Display Port) Enable HDMI 4K support for Digital Display Port only [Disable] : DP support 2160P HDMI support 1080P [Enable] : DP not support HDMI support 2160P ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... -
Page 86: Security
4.5 Security Figure 4-5 : BIOS Security Menu Administrator Password Set administrator password. User Password Set user password. Secure Boot Customizable Secure Boot Settings. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... - Page 87 Secure Boot Mode Secure Boot mode selector Standard/Custom. In custom mode Secure Boot Variables can be configured without authentication. Key Management Enables expert users to modify Secure boot policy variables without full authentication. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER...
-
Page 88: Boot
Sets the system boot order. New Boot Option Policy Controls the placement of newly detected UEFI boot options. Hard Drive BBS Priorities Set the order of the Legacy devices in this group. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... -
Page 89: Save & Exit
Restore/Load Default values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. ©Vecow RCX-1500 PEG User Manual BIOS AND DRIVER... -
Page 90: Appendix A : Isolated Dio Guide
DIO 12 DI 5 DIO 5 DO 5 DIO 13 DI 6 DIO 6 DO 6 DIO 14 DI 7 DIO 7 DO 7 DIO 15 DI COM DIO_GND DIO_GND DIO_GND DIO_GND External VDC ©Vecow RCX-1500 PEG User Manual Appendix A... - Page 91 DIO Connector (NPN, Default) 6-48V DC DIO_VDC (Pin 20) DO (Pin 11-18) DIO_GND (Pin 10, 19) Source Mode Device DIO Connector (PNP) 6-48V DC DIO_VDC (Pin 20) DO (Pin 11-18) DIO_GND (Pin 10, 19) ©Vecow RCX-1500 PEG User Manual Appendix A...
- Page 92 Sample folder include sample program, driver library, and API library. Source folder include sample program source code that compile on Visual Studio 2008. A.4 Sample Sample folder include x32 and x64 versions, as shown right : Sample RCX1K.exe, as shown below : ©Vecow RCX-1500 PEG User Manual Appendix A...
- Page 93 DO/DIO pin writable check button (pin 18 ~ pin 11/pin 18 ~ pin 11, pin 8 ~ pin 1) : User setting, DO/DIO pin writable of DIO configuration. Use for Read (DIO)/Write button activate. ©Vecow RCX-1500 PEG User Manual Appendix A...
- Page 94 Shown after Write button action. WDT setup day format texts (user setting) : User setting, WDT value, format : day'hour'minute'second. WDT counting day format text (read only) : WDT counting, format : day'hour'minute'second. ©Vecow RCX-1500 PEG User Manual Appendix A...
-
Page 95: Appendix B : Software Functions
1 : Output; 0 : Input Return : TRUE (1) : Success; FALSE (0) : Fail (Initial error, or call by pointer error, or hardware problem) BOOL SetDIO1Config (BYTE Isolate_Type, BYTE DI_NPN, BYTE DO_NPN, ©Vecow RCX-1500 PEG User Manual Appendix B... - Page 96 DO ([7:0]) : Output state, pin setting by hexadecimal bitmask 1 : High; 0 : Low Return : TRUE (1) : Success; FALSE (0) : Fail (Initial error, or hardware problem) BOOL GetDIO1 (WORD *DI) ©Vecow RCX-1500 PEG User Manual Appendix B...
- Page 97 FALSE (0) : Fail (Initial error, or setup 0 error, or hardware problem) BOOL CancelWDT () Cancel watchdog timer Return : TRUE (1) : Success; FALSE (0) : Fail (Initial error, or hardware problem) ©Vecow RCX-1500 PEG User Manual Appendix B...
-
Page 98: Appendix C : Raid Functions
1. Please select SATA device to RAID mode on BIOS menu. Advanced → SATA Configuration → SATA Mode Selection → RAID (Skylake platform) / Intel RST Premium (Kaby Lake/Coffee Lake platform) 2. Please select Software Feature Mask Configuration on BIOS menu. ©Vecow RCX-1500 PEG User Manual Appendix C... - Page 99 3. Use RST Legacy OROM → Disabled → Save Changes and Reset. 4. Into BIOS menu again, select Intel(R) Rapid Storage Technology on BIOS menu. 5. Select Create RAID Volume on BIOS menu. ©Vecow RCX-1500 PEG User Manual Appendix C...
- Page 100 You can get the software from driver CD. Also, you can find the latest information and software directly from Intel's website. http://www.intel.com/p/en_US/support/highlights/chpsts/imsm The RAID environment has been done if you completed the steps above. ©Vecow RCX-1500 PEG User Manual Appendix C...
- Page 101 "RAID 1". C.7 Disk Management : Partition the Disk After RAID 1 volume is created, you can see the figure of SATA device allocation. You will find "Volume_0000" in SATA device at BIOS menu. ©Vecow RCX-1500 PEG User Manual Appendix C...
- Page 102 Then add "Logical Device" for Windows access. C.8 If One SATA HDD on RAID Volume is Out-of-use After RAID 1 volume is created, you can see the figure of SATA device allocation. HDD CAUTION Sign ©Vecow RCX-1500 PEG User Manual Appendix C...
- Page 103 A warning will pop-up to ask you if the disk is not a member of the original RAID volume. If you press "Rebuild", it will replace the broken SATA HDD to the last SATA HDD of RAID volume. ©Vecow RCX-1500 PEG User Manual Appendix C...
-
Page 104: Appendix D : Power Consumption
SATA 0 Transcend SATA SSD420 128GB SATA 1 Seagate HDD 500GB LAN1 (i219) 1.0 Gbps LAN2 (i210) 1.0 Gbps Graphics output Power plan Balance(Windows10 Power plan) Power Source MEAN WELL RSP-1500-12 Test Program FurMark ©Vecow RCX-1500 PEG User Manual Appendix D... - Page 105 3% Input Current Consumption Current Consumption Core™ i7-8700 0.731A 08.77W 3.754A 45.05W Power on and boot to Win10 64-bit Run 100% CPU usage Power without 3D Input Current Consumption Core™ i7-8700 40.235A 482.82W ©Vecow RCX-1500 PEG User Manual Appendix D...
-
Page 106: Appendix E : Supported Memory & Storage List
*2 (Socket 1; Socket 2) PASS PASS PASS PASS *2 (Socket 3; Socket 4) PASS PASS PASS PASS *1 (Socket 1) *1 (Socket 2) PASS PASS PASS *1 (Socket 3) *1 (Socket 4) PASS PASS PASS ©Vecow RCX-1500 PEG User Manual Appendix E... - Page 107 Kingston 4GB DDR4-2666 SO-DIMM KVR26S19S6/4 25ºC 25ºC Kingston 8GB DDR4-2666 SO-DIMM KVR26S19S8/8 25ºC 25ºC Kingston 16GB DDR4-2666 SO-DIMM KVR26S19D8/16 25ºC 25ºC ADATA 8GB DDR4-2666 SO-DIMM AD4S266638G19-BSSC 25ºC 25ºC ADATA 16GB DDR4-2666 SO-DIMM AD4S2666316G19-BSSC 25ºC ©Vecow RCX-1500 PEG User Manual Appendix E...
- Page 108 25ºC 25ºC SLINK 32G DDR4 2666 SO-DIMM J4BGDS2G8QHKC 25ºC 25ºC SLINK 32G DDR4 2666 SO-DIMM J4BGDS2G8QHKI 25ºC 25ºC SLINK 16G DDR4 2666 SO-DIMM J4AGDH1G8QHKC 25ºC 25ºC SLINK 8G DDR4 2666 SO-DIMM J48GDH1G8QHJC 25ºC ©Vecow RCX-1500 PEG User Manual Appendix E...
- Page 109 ISSS332-128GM 128GB ADATA ISSS332-256GM 256GB IM2P33F8-128GD 128GB ADATA IM2P33F8-256GD 256GB M.2 SSD Toshiba KXG50ZNV512G 512GB (PCIe) Phison ESMP256GTB3C2-E12 256GB FORESEE FSGMMC-256G 256GB ** If more help is needed, please contact Vecow Technical Support. ©Vecow RCX-1500 PEG User Manual Appendix E...
-
Page 110: Appendix F : How To Install Power Supply
APPENDIX F : How to Install Power Supply F.1.1 RSP-1500-12 Adapter AC Cable RSP-1500-12 GREEN BLACK AC/L WHITE AC/N F.1.2 RSP-1500-12 Adapter DC Cable RSP-1500-12 ©Vecow RCX-1500 PEG User Manual Appendix F... - Page 111 F.1.3 RSP-1500-12 Adapter PEG Cable RSP-1500-12 F.1.4 RSP-1000-12 Adapter Cable ** If more help is needed, please contact Vecow technical support. ©Vecow RCX-1500 PEG User Manual Appendix F...
- Page 112 No part of this publication may be reproduced in any form or by any means, electric, photocopying, or recording, without prior authorization from the publisher. The rights of all the brand names, product names, and trademarks belong to their respective owners. © Vecow Co., Ltd. 2019. All rights reserved.