This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of Vecow Co., Ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of the product or documentation or any infringements upon the rights of third parties, which may result from such use.
Page 4
Order Information Part Number Description ® ® ECS-9700, Intel Xeon E3-1505M v5, ECS-9740-505M- ® NVIDIA GeForce GTX1050 Ti, 6 GigE LAN w/4 PoE , 2 SSD, GTX1050T 6 USB 3.0, 4 COM, 4 SIM, 32 Isolated DIO (ECC supported) ® ®...
Page 5
Order Accessories Part Number Description DDR4 16G Certified DDR4 16GB 2133MHz RAM DDR4 8G Certified DDR4 8GB 2133MHz RAM DDR4 4G Certified DDR4 4GB 2133MHz RAM PWA-280WB-WT 280W, 24V, 85V AC to 264V AC Power Adapter with 3-pin Terminal Block (7.62mm pitch), Wide Temperature -30°C to +70°C PWA-160WB-WT 160W, 24V, 85V AC to 264V AC Power Adapter with 3-pin...
Table of Contents CHAPTER 1 GENERAL INTRODUCTION 1.1 Overview 1.2 Features 1.3 Product Specification 1.3.1 Specifications of ECS-9740 GTX1050 1.3.2 Specifications of ECS-9600 GTX1050 1.4 Supported CPU List 1.5 Mechanical Dimension 1.5.1 Dimensions of ECS-9740 GTX1050 1.5.2 Dimensions of ECS-9600 GTX1050 CHAPTER 2 GETTING TO KNOW YOUR ECS-9700/9600 GTX1050 2.1 Packing List...
Page 7
CHAPTER 4 BIOS SETUP 4.1 Entering BIOS SETUP 4.2 Main 4.3 Advanced 4.4 Chipset 4.5 Security 4.6 Boot 4.7 Save & Exit APPENDIX A : Isolated DIO Guide APPENDIX B : Software Functions APPENDIX C : RAID Installation Guide APPENDIX D : Power Consumption APPENDIX E : Supported Memory &...
DirectX 12.1, OpenGL 4.5 and OpenCL 2.0 API, featuring multiple VGA, DVI, DisplayPort and HDMI display interfaces, up to 8K resolution and 6 independent HD displays, Vecow ECS GTX1050 series system offers more than 655% improved graphics performance than the one without an independent graphics engine;...
1.4 Supported CPU List Processor No. Cache Max. Frequency Embedded ® Xeon E3-1575M v5 Up to 3.00 GHz ® Xeon E3-1545M v5 Up to 2.90 GHz ® Xeon E3-1535M v5 Up to 2.80 GHz ® Xeon E3-1515M v5 Up to 2.80 GHz ®...
SSD/HDD and DDR4 SO-DIMM. Please verify these items if necessary.) ECS-9740 GTX1050 Accessory box, which contains ● Vecow Drivers & Utilities DVD ● Wall-mounting bracket ● KHS#6-32x6 screw for wall-mounting bracket ● M2.5x6 screw for Mini PCIe Slot ●...
2.2 Front Panel I/O & Functions In Vecow ECS-9700/9600 GTX1050 series family, all I/O connectors are located on the front panel and the rear panel. Most of the general connections to computer device, such as USB, LAN Jack, Audio, VGA, Display, DVI-D and other additional storage, are placed on the front panel.
Page 18
2.2.2 Reset Tact Switch SIM 1 SIM 3 DVI-D LAN 1 SIM 2 WLAN CFast LAN 2 It is a hardware reset switch. Please use this switch to reset ECS-9700/9600 GTX1050 without power off. Press the Reset Switch for a few seconds, and then reset will be enabled.
The DVI-D connector on the front panel supports DVI display. This connector can output DVI signal. The DVI output mode supports up to 1920 x 1200 resolution and the DVI is automatically selected according to the display device connected. You will need a DVI-D cable when connecting to a display device. 2.2.6 VGA Connector SIM 1 SIM 3...
2 work in normal status, iAMT 11.0 function is enabled. When using suitable RJ-45 cable, you can connect the system to other computers or to any other devices with Ethernet connection; for example, a hub or a switch. Moreover, both of LAN 1 and LAN 2 support Wake on LAN and Pre-boot functions. The pin-outs of LAN 1 and LAN 2 are listed as follows: Pin No.
SIM 2 WLAN CFast LAN 2 There is a system FAN on front side for airflow direction outward. You can adjust the FAN Speed from Vecow BIOS Setting. (refer to 4.3.7_Hardware Monitor_FAN PWM Value) GETTING TO KNOW YOUR ECS-9700/ 9600 GTX1050...
2.3.3 COM Ports DIO 2 DIO 1 DC-IN Isolated Isolated LAN6 LAN5 LAN4 LAN3 COM 2 PIN 1 ~ 8 PIN 11 ~ 18 PIN 1 ~ 8 PIN 11 ~ 18 On | Off COM 1 COM 4 COM 3 HDMI Serial port 1 to 4 (COM 1 to 4) can be configured for RS-232, RS-422, or RS- 485 with auto flow control communication.
Page 28
2.3.4 Rear USB 3.0 DIO 2 DIO 1 DC-IN Isolated Isolated LAN6 LAN5 LAN4 LAN3 COM 2 PIN 1 ~ 8 PIN 11 ~ 18 PIN 1 ~ 8 PIN 11 ~ 18 On | Off COM 1 COM 4 COM 3 HDMI There are 2 USB 3.0 connections available supporting up to 5GB per second...
Page 30
2.3.6 Isolated DIO DIO 2 DIO 1 DC-IN Isolated Isolated LAN6 LAN5 LAN4 LAN3 COM 2 PIN 1 ~ 8 PIN 11 ~ 18 PIN 1 ~ 8 PIN 11 ~ 18 On | Off COM 1 COM 4 COM 3 HDMI There is a 32-bit (16-bit DI, 16-bit DO) with 2 DIO connectors in the rear side.
Page 32
JP11 JP10 DO reference circuit: Sink Mode Device DIO Connector (NPN, Default) 6-48V DC DIO_VDC (Pin 20) DO (Pin11-18) DIO_GND (Pin10,19) Source Mode Device DIO Connector (PNP) 6-48V DC DIO_VDC (Pin 20) DO (Pin11-18) DIO_GND (Pin10,19) 2.3.7 3 of 3 Independent Displays DIO 2 DIO 1 DC-IN...
Page 34
2.4.2 UPS Power Connector For UPS module optional, we use 4.2mm 2x2p power connector This system has a UPS power input connector for optional part UPS module. CN36 Pin No. Definition Pin No. Definition Ground Ground +VDC_IN +VDC_IN (10~36V, Max.8A) (10~36V, Max.8A) 2.4.3 Miscellaneous Pin Header 2.0mm 2x4p header...
Page 36
2.4.5 BIOS Socket If the BIOS needs to be changed, please contact the Vecow RMA service team. 2.4.6 SATA Connector Standard 7 PIN SATA Connector There are 4 onboard high performance Serial ATA III. It supports higher storage capacity with less cabling effort and smaller required space. SATA4 is only for BOM option, default without function.
Page 38
CN20 Pin No. Definition Pin No. Definition USB +VCC (+V5/Max. 0.5A) DATA- DATA+ Ground 2.4.9 SUMIT A, SUMIT B (Optional) This system has standard SUMIT A and SUMIT B for SUMIT type add on cards. SUMITB SUMITA GETTING TO KNOW YOUR ECS-9700/ 9600 GTX1050...
Page 43
Panasonic BR2032 190mAh lithium battery. It is recommended that you do not have to get the lithium battery on your own. If the battery needs to be changed, please contact the Vecow RMA service team. 2.4.12 FAN Header Fan power connector supports for additional thermal requirements.
Page 44
2.4.13 LPC Port 80 Header ECS-9700/9600 GTX1050 provides a LPC Port 80 header for debug card. Pin out: Pin No. Function Pin No. Function SERIRQ LFRAME# +3.3V LAD0 RESET# Ground LAD1 CLOCK LAD2 Ground 2.4.14 LAN IEEE 1588 Header ECS-9700/9600 GTX1050 provides a LAN header for IEEE 1588. LAN No.
Page 46
2.4.15 COM Port Header ECS-9700/9600 GTX1050 provides 4 COM port headers for internal COM port cables. CN27 CN28 Pin out: CN27: CN28: Pin No. Description Port Pin No. Description Port Ground_Frame COM3 Ground_Frame COM4 Ground COM3 Ground COM4 COM3 COM4 COM3 COM4 COM3...
Page 48
You may configure your card to match the needs of your application by DIP switch as shown below (the deep switch on and off) 1 : OFF 1 : ON 1 : ON 2 : OFF 2 : OFF 2 : ON 2.5.2 USB Power Jumper Jumper Setting...
Page 50
2.5.4 COM Port RS-422/RS-485 Receiver Terminator COM RS-422/485 COM / DIP Switch ON / OFF Receiver Terminator *Enable COM1 / SW3-1 Disable COM RS-422/485 COM / DIP Switch ON / OFF Receiver Terminator *Enable COM2 / SW3-2 Disable COM RS-422/485 COM / DIP Switch ON / OFF Receiver Terminator...
2.6 Ignition Control ECS-9700/9600 GTX1050 series provides ignition power control feature for in- vehicle applications. The built-in MCU monitors the ignition signal and turns on/ off the system according to pre-defined on/off delay periods. 2.6.1 Adjust Ignition Control Modes ECS-9700/9600 GTX1050 series provides 16 modes of different power on/off delay periods adjustable via SW5 switch.
Page 54
2.6.2 Ignition Control Wiring To activate ignition control, you need to provide IGN signal via the 3-pin pluggable terminal block located in the back panel. Please find below the general wiring configuration. Pin No. Definition Ignition (IGN) External Power S/W + External Power S/W + For testing purpose, you can refer to the picture above to simulate ignition signal input controlled by a latching switch.
SYSTEM SETUP 3.1 How to Open Your ECS-9700/9600 GTX1050 Step 1 Remove hole plugs. Step 2 Remove two F#6-32 screws (circled in red) and two F-M3 screws (circled in yellow) on the bottom side. HARDWARE INSTALLATION...
3.5 Installing SIM Card Step 1 Remove 2 pcs F-M3x4 screws on CFast & SIM Card. Step 2 Before Inserting CFast & SIM Card, make sure ECS-9700/9600 GTX1050 power is not plugged. Step 3 Insert CFast card and push to lock. Step 4 Insert SIM card and push to lock.
Page 66
3.7.2 VESA Mount Step 1 ECS-9700/9600 GTX1050 and VESA Mount. Step 2 Take ECS-9700/9600 GTX1050 and VESA Mount with fasten 4pcs KHS#6-32 screws. HARDWARE INSTALLATION...
Page 68
3.7.3 Din Rail Kit Step 1 ECS-9700/9600 GTX1050 and Din Rail Kit. Step 2 Take ECS-9700/9600 GTX1050 and Din Rail Kit and fasten four KHS#6-32 screws in the four marked corners. HARDWARE INSTALLATION...
BIOS SETUP 4.1 Entering BIOS SETUP Figure 4-1: Entering Setup Screen BIOS provides an interface for users to check and change system configuration. The BIOS setup program is accessed by pressing the <Del> key when POST display output is shown. BIOS AND DRIVER SETTING...
4.3.1 Trusted Computing Figure 4 3-1: Trusted Computing Control the TPM device status and display related information if TPM chip is present. 4.3.2 ACPI Settings Figure 4 3-2: ACPI Settings Enable Hibernation Enables or disables system's ability to hibernate (OS/S4 sleep state). This option may not be effective with some OS.
Page 74
4.3.6 IT8786 Super IO Configuration Figure 4-3-6-1: Super IO Settings Figure 4-3-6-2: Serial Port Settings Serial Port 1 to port 4 Configuration Options for Serial Port 1 to Serial Port 4. Entering the corresponding Port option then end user can change the settings such as I/O resource and UART mode.
Page 76
4.3.9 CPU Configuration Figure 4 3-9: CPU Function Settings Hyper-threading Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and disabled for other OS (OS not optimized for Hyper-Threading Technology). When disabled only one thread per core is enabled. Active Processor Cores Number of cores to enable in each processor package.
Page 78
SATA Controller(s) Enable or disable SATA Device. SATA Mode Selection Determines how SATA controller(s) operate. Software Feature Mask Configuration RAID OROM/RST driver will refer to the SWFM configuration to enable or disable the storage features. Aggressive LPM Support Enable PCH to aggressively enter link power state. SATA Controller Speed Indicates the maximum speed the SATA controller can support.
Page 80
4.3.14 USB Configuration Figure 4 3-14: USB Settings Legacy USB Support Enables Legacy USB support. AUTO option disables Legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. XHCI Hand-off This is a workaround for OS-es without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.
Page 82
4.4.2 Graphics Configuration of System Agent (SA) Figure 4-4-2: Graphics Settings Graphics Turbo IMON Current Graphics turbo IMON current values supported (14-31). Skip Scaning of External Gfx Card If Enable, it will not scan for External Gfx Card on PEG and PCH PCIE Ports. Primary Display Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx.
Page 84
PCH LAN Controller Enable or disable onboard NIC. Wake on LAN Enable or disable integrated LAN to wake the system. (The wake On LAN cannot be disabled if ME is on at Sx state.) Serial IRQ Mode Configure serial IRQ mode. State After G3 Specify what state to go to when power is re-applied after a power failure (G3 state).
4.5 Security Figure 4-5: BIOS Security Menu Administrator Password Set administrator password. User Password Set user password. 4.5.1 HDD Security Configuration Figure 4-5-1: HDD Security Settings Set User Password Set HDD user password. *** Advisable to power cycle system after setting hard disk passwords *** Discard or save changes option in setup does not have any impact on HDD when password is set or removed.
4.7 Save & Exit Figure 4-7: Bios Save and Exit Menu Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset Reset the system after saving the changes. Discard Changes and Reset Reset system setup without saving any changes.
Page 92
A.3 Software Package Contain Distribution folder include x32 and x64 versions, use batch file for installation. There are included as fallowed: Win7_32.bat: Installation for 32-bit driver Win7_64.bat: Windows update package which driver required (need to restart), and Installation for 64-bit driver Win8_32.bat, Win8_64.bat: Installation for driver, and guideline to Framework 3.5 distribution for sample...
Page 94
DIO1 / DIO2 group: Isolate check button: DIO type of DIO configuration, isolated / non-isolated, defined in ECS-9000 series user manual. Read button: Set DIO configuration to get DI / DIO input state. DO type check button: User setting, DO type of DIO configuration to setup 8 pins - Source / Sink. Use for Write (DO) button activate.
APPENDIX B : Software Functions B.1 Driver API Guide In Runtime folder, on ECS9K7.h: _DLL_IMPORT_ definition is used on LoadLibrary API for ECS9K7.dll. ECS9K_EXPORTS definition is used on ECS9K7.dll building. Otherwise, that is used to compile with ECS9K7.lib. BOOL Initial(BYTE Isolate_Type, BYTE DIO_NPN) Initial machine for DIO, watchdog timer, and POE Isolate_Type: DIO type 1: Isolated DIO;...
APPENDIX C : RAID Installation Guide C.1 SATA Mode for RAID Please select SATA device to RAID mode on BIOS menu. Advanced → SATA Configuration → SATA Mode Selection C.2 OS Installation ECS-9700/9600 GTX1050 is featured with eight SATA, option 1: include four internal SATA, three mSATA and one CFast.
Page 102
C.7 Disk Management : Partition the Disk After RAID 1 volume created, you can see the figure of SATA device allocation. You will find “Volume_0000” in SATA device at BIOS menu. To start Disk Management tool, select "initialize disk." Then add “Logical Device” for Windows access. C.8 If One SATA HDD on RAID Volume is Out-of-use After RAID 1 volume created, you can see the figure of SATA device allocation.
APPENDIX D : Power Consumption Testing Board ECS-9700 GTX1050 8GB X 2 USB-1 USB Keyboard Logitech M105 USB-2 USB Mouse Microsoft 1113 USB-3 USB Flash Transecnd 3.0 8GB USB-4 USB Flash Transecnd 3.0 8GB CFAST innodisk Cfast 3ME 32GB SATA 0 MEMXPRO SATA M3A 256GB LAN 1 (i219) 1.0 Gbps...