Page 1
USER USER EVS-2000 Manual Manual 10th Gen. Intel ® Xeon ® /Core ™ i9/i7/i5/i3 Fanless AI Computing System with NVIDIA ® /AMD MXM GPU Graphics, High Performance Expandable 1.3.0 Edition 20210311...
Page 2
Record of Revision Version Date Page Description Remark 1.00 01/28/2021 Official Release 1.10 01/29/2021 29, 42 Update 1.20 02/25/2021 8, 10 Update 1.30 03/11/2021 4, 6, 8, 10, 20 Update...
Page 3
This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specifications are subject to change without prior notice. Vecow Co., Ltd. is under no legal commitment to the details of this document. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of this document, the products, or any third party infringements, which may result from such use.
Page 4
Order Information Part Number Description EVS-2000, 2 GigE LAN, 1 PCIe x4, 6 USB 3.2, 3 COM, 2 SIM, EVS-2010 32 Isolated DIO, Fanless EVS-2000, 2 GigE LAN, 1 PCI, 6 USB 3.2, 3 COM, 2 SIM, EVS-2001 32 Isolated DIO, Fanless EVS-2000, 2 GigE LAN, 1 PCIe x4, 6 USB 3.2, 3 COM, 2 SIM, EVS-2010F 32 Isolated DIO, With System Fan...
Page 5
Order Accessories Part Number Description DDR4 32G Certified DDR4 32GB 3200MHz RAM DDR4 16G Certified DDR4 16GB 3200MHz RAM DDR4 8G Certified DDR4 8GB 3200MHz RAM DDR4 4G Certified DDR4 4GB 3200MHz RAM 160W, 24V, 85V AC to 264V AC Power Adaptor with 3-pin PWA-160WB-WT Terminal Block (7.62mm pitch), Wide Temperature -30°C to +70°C 280W, 24V, 85V AC to 264V AC Power Adaptor with 3-pin...
Table of Contents CHAPTER 1 GENERAL INTRODUCTION 1.1 Overview 1.2 Features 1.3 Product Specification 1.3.1 Specifications of EVS-2010 1.3.2 Specifications of EVS-2001 1.3.3 Specifications of EVS-2010F 1.3.4 Specifications of EVS-2001F 1.4 Supported CPU List 1.5 Mechanical Dimension 1.5.1 Dimensions of EVS-2000 1.5.2 Dimensions of EVS-2000F CHAPTER 2 GETTING TO KNOW YOUR EVS-2000 2.1 Packing List...
Page 7
3.8 Installing SD Card 3.9 Installing PCI/PCIe Card 3.10 Installing SSD/HDD 3.11 Mounting Your EVS-2000 CHAPTER 4 BIOS AND DRIVER 4.1 BIOS Settings 4.2 Main 4.3 Advanced 4.4 Chipset 4.5 Security 4.6 Boot 4.7 Save & Exit APPENDIX A : Isolated DIO Guide APPENDIX B : Software Functions APPENDIX C : RAID Functions APPENDIX D : Power Consumption...
Featuring advanced NVIDIA with NVIDIA Turing™ architecture technology or AMD Graphics in the support for MXM 3.1 Type A and Type B form factor, Vecow EVS-2000 supports up to 7 independent displays with up to 8K resolution, delivering astounding visual computing performance and accelerating compact- specific applications.
1.4 Supported CPU List Max. Series Cores Cache Frequency Memory W-1290TE Up to 4.5GHz ® Intel W-1270TE Up to 4.4GHz ® Xeon W-1250TE Up to 3.8GHz i9-10900E Up to 4.7GHz i9-10900TE Up to 4.5GHz i7-10700E Up to 4.5GHz i7-10700TE Up to 4.4GHz ®...
Item Description EVS-2000 Expandable Fanless Embedded System (According to the configuration of you order, the EVS-2000 series may contain SSD/HDD and DDR4 SO-DIMM. Please verify these items if necessary.) EVS-2000 series accessory box, which contains • Vecow Drivers & Utilities DVD...
EVS-2000F Expandable Embedded System (According to the configuration of you order, the EVS-2000F series may contain SSD/ HDD and DDR4 SO-DIMM. Please verify these items if necessary.) EVS-2000F series accessory box, which contains • Vecow Drivers & Utilities DVD Item Description Outlook...
2.2 Front Panel I/O & Functions In Vecow EVS-2000 series family, all I/O connectors are located on front panel and rear panel. Most of the general connections to computer device, such as USB, LAN Jack, Audio, Display, VGA, DVI-D and any additional storage, are placed on the front panel.
Page 24
2.2.4 HDD LED Indicator Micro SD / SIM1 / SIM2 DVI-D LAN 2 LAN 1 HDD LED/Yellow : A Hard Disk. If the LED is on, it indicates that the system's storage is functional. If it is off, it indicates that the system's storage is not functional.
Page 26
2.2.8 USB 3.0 Micro SD / SIM1 / SIM2 DVI-D LAN 2 LAN 1 There are 4 USB 3.0 connections available supporting up to 5GB per second data rate in the front side of EVS-2000. It is also compliant with the requirements of Speed (SS), High Speed (HS), Full Speed (FS) and Low Speed (LS).
Page 28
2.2.11 Micro SD card Micro SD / SIM1 / SIM2 DVI-D LAN 2 LAN 1 There is a micro sd card socket on the front panel. The pin outs of micro sd port are listed as follows : Pin No. Description Pin No.
Page 30
2.3.3 COM Ports Serial port 1~4 (COM 1~4) can be configured for RS-232, RS-422, or RS-485 with auto flow control communication. The default definition of COM 1 to COM4 is RS-232; but if you want to change to RS-422 or RS-485, you can find the setting in BIOS.
Page 32
2.3.4 Rear USB 3.0 There are 2 USB 3.0 connections available supporting up to 5GB per second data rate in the rear side of EVS-2000. It is also compliant with the requirements of Super Speed (SS), High Speed (HS), Full Speed (FS) and Low Speed (LS). 2.3.5 DisplayPort Onboard Display Port supports auxiliary channel dual mode, and the connection supports up to 7680 x 3840 resolution at 60Hz.
Page 38
64GB. (Each channel 16GB) SODIMM2 SODIMM1 Slot Description SODIMM1 DDR4 Channel A SODIMM2 DDR4 Channel B 2.4.4 BIOS Socket (CN1) If the BIOS need to be changed, please contact the Vecow RMA service team. BIOS GETTING TO KNOW YOUR EVS-2000...
Page 40
2.4.7 DEBUG Connector (DEBUG1) DEBUG1 This pin header is through by LPC interface and pins define are listed in the following table. Pin No. Pin Name Pin No. Pin Name 3.3V SERIRQ FRAME# 24M CLCOK RESET 2.4.8 SUMIT Connector (SUMITA1/SUMITB1) SUMITB1 SUMITA1 GETTING TO KNOW YOUR EVS-2000...
Page 44
The system's real-time clock is powered by a lithium battery. It is Equipped with Panasonic BR2032 190mAh lithium battery. It is recommended that you not replace the lithium battery on your own. If the battery needs to be changed, please contact the Vecow RMA service team. GETTING TO KNOW YOUR EVS-2000...
Page 46
2.4.13 COM Port (COM1-COM4) EVS-2000 provides 4 serial ports (COM1-COM4) headers for internal COM port cable and the pin define are listed in the following table. COM1 COM2 COM3 COM4 COM3 Pin No. Description Pin No. Description Ground GETTING TO KNOW YOUR EVS-2000...
Page 48
Pin No. Description Pin No. Description PCIE_TX_N PCIE_TX_P Mechanical Key LED2# USB- LED1# USB+ +V3.3_AUX +V3.3_AUX 2.4.15 M.2 KEY-M (M2M_CN1) M.2 KEY M : PCIe x4/SATA Support M.2 key M connector is suitable for applications that use Host I/Fs supported by either PCIe or SATA, or Solid State Storage Devices (SSD).
2.5 Main Board Jumper Settings 2.5.1 Board Top View of EVS-2000 Main Board with Jumper and DIP Switch The figure below is the top view of EVS-2000 main board which is the main board. It shows the location of the jumpers and the switches. JUSBPWR1 JRI_PWR1 JRI_PWR2...
2.6.1 Adjust Ignition Control Modes EVS-2000 series provides 16 modes of different power on/off delay periods adjustable via SW2 switch. The default rotary switch is set to 0 in ATX/AT power mode. For the setting of software IGN, please refer to 4.4.3 GPIO Manager Control.
Page 56
Item Power On Delay Power Off Delay Switch Position ATX/AT mode (Default) No delay No delay No delay 5 seconds No delay 10 seconds No delay 20 seconds 5 seconds 30 seconds 5 seconds 60 seconds 5 seconds 90 seconds 5 seconds 30 minutes 5 seconds...
SYSTEM SETUP 3.1 How to Open Your EVS-2000 Step 1 Remove one F-M3x4L screw. Step 2 Remove one F-M3x4L (Red) and trigger and open PCI cover (Blue). SYSTEM SETUP...
3.6 Installing Antenna Cable Step 1 Remove the rubber corks on the front and side. Step 2 Put antenna cable connector into the hole on panel. SYSTEM SETUP...
3.7 Installing SIM Card Step 1 Remove two F-M3x4L screws on SD & SIM cover. Step 2 Inserting SIM Card, make sure the system power is not plugged. SYSTEM SETUP...
3.9 Installing PCI/PCIe Card Step 1 Check PCI/PCIe Slot supports the maximum length 200 mm (without card bracket) of PCI/PCIe expansion card. Step 2 Remove one M3x5L and PCI bracket. SYSTEM SETUP...
3.11 Mounting Your EVS-2000 3.11.1 Wall Mount Bracket for EVS-2000 with four M3x6L screws. 3.11.2 Wall Mount Bracket for EVS-2000F with four M3x6L screws. SYSTEM SETUP...
Page 82
3.11.4 EVS-2000/2000F Din Rail with VESA Mount Kit Step 1 Remove six F-M3x6L screws. Step 2 Install Din Rail with VESA Mount Kit and fasten six I-M3x6L screws. SYSTEM SETUP...
4.2 Main Figure 4-2 : BIOS Main Menu The main menu displays BIOS version and system information. There are two options on Main menu. System Date Set the date. Use <Tab> to switch betwe en date elements. System Time Set the time. Use <Tab> to switch between time elements. 4.3 Advanced Figure 4 3 : BIOS Advanced Menu Select advanced tab to enter advanced BIOS setup options, such as CPU...
Page 86
4.3.2 Power & Performance Figure 4 3-2 : Power & Performance 4.3.2.1 CPU – Power Management Control Figure 4 3-2-1 : CPU – Power Management Control Boot performance mode Select the performance state that the BIOS will set before OS handoff. Intel (R) SpeedStep (tm) Allows more than two frequency ranges to be supported.
Page 88
4.3.4 Trusted Computing Figure 4 3-4 : Trusted Computing Control the TPM device status and display related information if TPM chip is present. 4.3.5 ACPI Settings Figure 4 3-5 : ACPI Settings Enable Hibernation Enables or disables system's ability to hibernate (OS/S4 sleep state). This option may not be effective with some OS.
Page 90
4.3.8 Hardware Monitor Figure 4-3-8 : Hardware Monitor Settings The IT8786 SIO features an enhanced hardware monitor providing thermal, fan speed, and system voltages' status monitoring. Smart Fan Support Smart Fan Support. Work with Full Speed if "Smart Fan Support" is Disabled. Smart Fan Mode Default : Using the default smart fan table.
Page 92
4.3.11 Acoustic Management Configuration Figure 4-3-11 : Acoustic Management Settings Acoustic Management Configuration Option to enable or disable automatic acoustic management. 4.3.12 PCI Subsystem Setting Figure 4-3-12 : PCI Subsystem Settings Above 4G Decoding Globally Enables or Disables 64-bit capable Devices to be Decoded in Above 4G Address Space (Only if System Supports bot PCI Decoding) Hot-Plug Support Globally Enables or Disables Hot-Plug support for the entire System.
Page 94
4.3.15 NVMe Configuration Figure 4-3-15 : NVMe Settings Display NVMe controller and Drive information. 4.3.16 USB Configuration Figure 4-3-16 : USB Settings Legacy USB Support Enables Legacy USB support. AUTO option disables Legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
Page 98
4.4.1.1 Memory Configuration Figure 4-4-1-1 : Memory Information Displays memory information. 4.4.1.2 Graphics Configuration Figure 4-4-1-2 : Graphics Settings Skip Scaning of External Gfx Card If Enable, it will not scan for External Gfx Card on PEG and PCH PCIE Ports. Primary Display Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx.
Page 100
4.4.2.1 PCI Express Configuration of PCH-IO Figure 4-4-2-1 : PCH-IO Settings DMI Link ASPM Control Enable/Disable the control of Active State Power Management on SA side of the DMI Link. Native PCIE Enable PCIE Express Native Support Enable/Disable. PCI Express device settings Bios options for PCI Express device setting.
Page 102
4.4.3 GPIOManager Control Figure 4-4-3 : GPIOManager Settings DVI/VGA DDC channel selection DVI/VGA DDC channel selection for DVI-I connector System Fan 2 Speed System Fan 2 Speed control (SYS_FAN2) Ignition F/W Version Indicate current ignition f/w version Current Ignition control method [Hardware] Ignition mode control by hardware switch.
Page 104
4.5.1 HDD Security Configuration Figure 4-5-1 HDD Security Settings Set User Password Set HDD user password. *** Advisable to power cycle system after setting hard disk passwords *** Discard or save changes option in setup does not have any impact on HDD when password is set or removed.
4.7 Save & Exit Figure 4-7 : Bios Save and Exit Menu Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset Reset the system after saving the changes. Discard Changes and Reset Reset system setup without saving any changes.
Page 108
A.2 Isolated DIO Signal Circuit DI Reference Circuit : Sink Mode (NPN) Power DIO Connector Supply DI_COM (Pin 9) 6-48V DC DI (Pin1-8) Source Mode (PNP) Power DIO Connector Supply DI_COM (Pin 9) 6-48V DC DI (Pin1-8) DO Reference Circuit : Sink Mode Device DIO Connector...
APPENDIX B : Software Functions B.1 Driver API Guide In Header folder, Vecow.h and VecowLinux.h contain usabled API for Windows/Linux. BOOL initial_SIO(BYTE Isolate_Type, BYTE DIO_NPN) Initial machine for IO and watch dogtimer. Isolate_Type : DIO type. 1 : Isolated DIO;...
Page 112
BOOL set_IO1_configuration(BYTE Iso, BYTE DI_mode, BYTE DO_mode, WORD Mask) BOOL set_IO2_configuration(BYTE Iso, BYTE DI_mode, BYTE DO_mode, WORD Mask) Set DIO configuration. Isolate_Type : DIO type. 1 : Isolated DIO; 0 : Non-Isolated DIO(GPIO). DI_mode ([7:0]) : DI type, pin setting by hexadecimal bitmask only for Isolated DIO. 0xFF : PNP (Source) mode for European rule;...
Page 114
BOOL initial_POE(BYTE Scan, BYTE ID) Initial POE. Scan : POEID scan type 2 : Auto scan; 1 : Manual setup. ID : POE ID by manual setting. Range : 0~15. Return : TRUE (1) : Success. FALSE (0) : Fail (Driver not exists, or version is too old, or out of range error). BOOL get_POE_configuration(BYTE ID, BYTE *Auto, BYTE *Mask) Get POE configuration (by variable).
APPENDIX C : RAID Functions C.1.1 SATA Mode for RAID Please select SATA Device to RAID mode on BIOS menu. Chipset → PCH-IO Configuration → SATA And RST Configuration → SATA Mode Selection → Intel RST Premium → Save Changes and Reset. C.1.2 UEFI Mode for RAID 1.
Page 118
C.3 To Install All Device Drivers of the System The instructions are as follows : 1. Install Chipset driver 2. Install Network driver 3. Install ME driver (if available) 4. Install Audio driver 5. Install VGA driver C.4 To Install "Intel Rapid Storage Technology" Software You can get the software on driver CD.
Page 120
C.9 Recovery and Auto Re-build When Using the SAME RAID HDD C.10 Recovery and Auto Re-build When Using DIFFERENT RAID HDD A warning will pop-up to ask you if the disk is not a member of the original RAID volume. If you press "Rebuild", it will replace the broken SATA HDD to the last SATA HDD of RAID volume.
Page 122
D.1 Intel® Core™ i5-10500E (12M Cache, 3.10GHz) Power on and boot to Win 10 (64-bit) Power on and boot to Win 10 (64-bit) Standby Mode Idle status CPU Power Sleep Mode usage less 3% Input Current Consumption Current Consumption Current Consumption Core™...
Page 124
D.3 Intel® Core™ i5-10500E (12M Cache, 3.10GHz) with MX RTX 2070 Power on and boot to Win 10 (64-bit) Power on and boot to Win 10 (64-bit) Standby Mode Idle status CPU Power Sleep Mode usage less 3% Input Current Consumption Current Consumption...
Page 126
D.5 Intel® Core™ i5-10500E (12M Cache, 3.10GHz) with MXM P2000 Power on and boot to Win 10 (64-bit) Power on and boot to Win 10 (64-bit) Standby Mode Idle status CPU Power Sleep Mode usage less 3% Input Current Consumption Current Consumption Current...
Page 128
D.7 Intel® Core™ i5-10500E (12M Cache, 3.10GHz) with MXM GTX 1050 Power on and boot to Win 10 (64-bit) Power on and boot to Win 10 (64-bit) Standby Mode Idle status CPU Power Sleep Mode usage less 3% Input Current Consumption Current Consumption...